WenmarOpen by Wenmar Pro

Service bulletins for the 2010 MINI Cooper

A bulletin is a manufacturer's communication to its dealers, as NHTSA indexes it. The summary is NHTSA's. The document is the manufacturer's: read it at NHTSA. A bulletin is not a recall, and listing a model year does not mean every vehicle of it is concerned.

161 on file from NHTSA, as of 2026-10-19.

By type

By component

By trouble code

Bulletins, newest first
M6502132018-12-03. Service bulletin. EQUIPMENT; EQUIPMENT:ELECTRICAL; ELECTRICAL SYSTEM. "HAMP2: Stored Radio Stations Deleted After Ignition Off. After ignition off, the stored radio stations (AM/FM and Satellite radio) are no longer available in: * Menu ""PRESETS"" * Preset buttons on the head unit Hardware error in the CHAMP2 head unit"
M3301102018-12-03. Service bulletin. SUSPENSION. Clicking Noise from Rear Suspension on Uneven Road Surface. A clicking noise is heard from the rear suspension on uneven roads CAUSE
M3402132018-12-03. Service bulletin. SERVICE BRAKES. Clicking Noise from Front Axle Brakes.
M6106072018-11-26. Service bulletin. VEHICLE SPEED CONTROL; ELECTRICAL SYSTEM. "Discharged Battery: Energy Diagnosis Must Be Performed. MINI electrical systems and advancements in vehicle technology have resulted in an increased demand on the vehicle battery. This SI will help the dealer handle ""discharged battery"" complaints. A discharged battery can have various causes, most unrelated to the battery. A failed battery is often the symptom and not the cause. A fully serviceable battery fails when an electrical component causes the battery to discharge; the battery becomes internally damaged and must be replaced. For more information, refer to http://www.batteryuniversity.com/parttwo-42B.htm. For this reason, replacing the battery is not usually a permanent repair. The cause of the discharged battery must be analyzed in order to guarantee a proper repair. To repair the vehicle properly the first time in the workshop, the diagnostic test plans must be performed to completion, with all results taken into consideration. Without performing the energy diagnosis test plan, the root cause of the discharged battery cannot be identified. This increases the chances of a repeat repair. CAUSE Discharged battery."
M1103092018-11-26. Service bulletin. ENGINE. Whistling Noise from the Water Pump Area. A whistling or squealing noise is heard from the engine at idle and/or at higher engine speeds. CAUSE 1. Noise is caused by the water pump. 2. Noise is caused by the friction wheel of the belt tensioner.
M8401132018-11-26. Service bulletin. EQUIPMENT. Telephone: Phonebook Does Not Transfer to the Vehicle. The telephone book does not transfer to the vehicle after the pairing process is completed. CAUSE Software error in the head unit
M6401132018-11-26. Service bulletin. EQUIPMENT; VISIBILITY. Red or Blue Cap Missing from Temperature Control Wheel. The customer states the red or blue cap is missing from the temperature control wheel of the heat and air conditioning control panel.
M5401132018-11-26. Service bulletin. EQUIPMENT; STRUCTURE:BODY:ROOF AND PILLARS. "White Wear Marks on Canvas Top. Wear marks appear on the convertible top on the left and/or right side C-pillar areas. A For vehicles produced to December 12, 2011 1. Replace the defective canvas convertible top. Refer to ISTA Repair Instruction 54 34 120, ""Replacing soft top fabric."" Note: The following repair steps must be performed before the new top is installed to prevent a repeat repair for wear marks. 2. With the defective canvas cover removed, the current main pillars must be replaced. Refer to ISTA Repair Instruction 54 34 996, ""Replacing left or right main pillar."" 3. The current locking mechanisms and bump stops must be replaced as well. Refer to ISTA Repair Instruction 54 34 196, ""Removing and installing / replacing both stowage locks."" The repair kit* needed is listed below. 7. Reinstall the removed parts in the reverse order of their removal. 8. Operate the top several times to quality check the repair."
M3601132018-11-26. Service bulletin. TIRES; EQUIPMENT; WHEELS. "MINI GP: Choice of Tire Option Agreement and Alternate Tire Retrofit. The Kumho 215/40 R17 Ecsta V700 sport tire performance optimization results in vehicle operation limitations, specifically when operated in cold climates or on wet, slushy or snow-covered roads. If your MINI JCW GP owner prefers a set of tires that better fits his/her driving style and climate, these owners can swap out the factory-original equipment (OE) Kumho 215/40 R17 Ecsta V700 sport tires for a set of the following MINI approved alternate tires: ??205/45R17 84W John Cooper Works performance run-flat tires Please refer to the attached MINI Product Planning & Strategy Bulletin M-20-0313-0012, ""MINI John Cooper Works GP Unleashed,"" for more information, including the required ""choice of tire option"" agreement form."
M1101132018-11-26. Service bulletin. ENGINE AND ENGINE COOLING. Service Action: Replace the Coolant Pump. Coolant is leaking from the coolant pump. CAUSE The coolant pump may develop cracks in the plastic housing. These cracks may result in a coolant leak.
M1101122018-11-26. Service bulletin. ENGINE. Engine Oil Leak. The customer states that a small engine oil leak can be seen from the underside of the engine. CAUSE The internal sealing of the oil pump volume control solenoid valve is compromised, allowing engine oil to leak from the oil pump volume control solenoid.
M8401132018-11-26. Service bulletin. EQUIPMENT. Telephone: Phonebook Does Not Transfer to the Vehicle. The telephone book does not transfer to the vehicle after the pairing process is completed. CAUSE Software error in the head unit
M5101132018-11-26. Service bulletin. VISIBILITY. Service Action: Replace Both Sun Visors. When opening the sun visor mirror cover, the pivot pins bind. The spring tension is too great and weak pivot pins can break.
M1201132018-11-26. Service bulletin. ENGINE AND ENGINE COOLING. "N16 Engine: FC 2D9B Knock Sensor, Signal Is Stored in the DME. Certain areas of the US experience extremely cold climate conditions during the winter months, which can cause the Service Engine Soon lamp to illuminate while the engine temperature is increasing to full operating temperature. The following fault may be stored in the DME: FC 2D9B Knock Sensor, Signal While performing test plan B1214 M KNOCK SENSOR, the following error message will be displayed: ""An error has occurred during execution of a service program. Fault code: 61/3."" This error in the test plan will not allow diagnosis to continue. The test plan error will be repaired with ISTA/D 2.36.0. CAUSE A DME calibration error in the knock sensor diagnostics results in an increased sensitivity threshold to cold temperatures."
M0701142018-11-26. Service bulletin. EQUIPMENT. ISTA Premium Repair Instructions. INFORMATION ISPI NEXT ISTA 3.45 introduces a new concept for displaying repair instructions. The new repair instructions have the following advantages compared to the old style: z All instructions (preliminary and follow-up) needed for the repair are included; hyperlinks are no longer needed. z All special tools needed for the repair can be viewed or printed from one tab in ISTA without leaving the repair instructions page. z All technical data and torque specs for the repair can be viewed from one tab in ISTA without leaving the repair instructions page. Currently repair instructions for the timing chain replacement "1131051 - Replace timing chain (N14)" have been converted to this new format. Refer to the attachment which describes how to access and use the instructions. To get initial feedback if any further changes are needed prior to converting all future repair instructions, we have converted the repair instructions used most often to this new concept. Please use these repair instructions when applicable and provide feedback using the attached feedback form. The form can be sent directly to Paul Labrie at Paul.Labrie@bmwna.com. Thanks for any feedback that you can provide. Paul Labrie Technical Service 201- 571-5247
M3401132018-11-26. Service bulletin. SERVICE BRAKES, HYDRAULIC. Erroneous "Service due" Message Though Brake Lining Thickness Sufficient. The CBS data calculated for the remaining distance of the front and/or rear brake pads does not agree with the actual brake pad thickness. The yellow brake lining service due indicator illuminates even though the pad thickness is greater than the minimum wear limit (approximately 3.7 mm); the brake wear sensor has not yet been activated (from a thickness of approx. 4.2 mm). In some cases, the red warning message may already be active. The CBS front/rear brake display is based on a mathematical calculation. Various influences are incorporated into this calculation (for example, vehicle speed, brake pressure, and rotor temperature). Due to changing driving characteristics and/or unfavorable environmental conditions, the calculated remaining distance may differ from actual pad thickness.
M3401122018-11-26. Service bulletin. SERVICE BRAKES. ABS/DSC Control During Light Braking. When driving slowly over uneven road surfaces, there may sometimes be pre-mature ABS application relative to the driving situation with the brake lightly applied. Software in the Dynamic Stability Control unit (DSC)
M1707122018-11-26. Service bulletin. ENGINE AND ENGINE COOLING. Service Action: Retrofit of the Engine Coolant Temperature Sensor. Internal corrosion could form in the engine coolant temperature sensor. This corrosion leads to internal bridging of the contacts, which can cause an inaccurate engine temperature reading. This false reading could lead to difficulty in the engine starting and/or a "Service Engine Soon" lamp being illuminated.
M8401142018-11-13. Service bulletin. ELECTRICAL SYSTEM. iPhone: Connection Failures with iOS 7. There are various connectivity failures with the iPhone using iOS 7. Some examples are listed below: z Call disconnection z Contact List incomplete z General connection failures Apple software iOS 7 and its variants
M1104142018-11-13. Service bulletin. EQUIPMENT; ELECTRICAL SYSTEM; ENGINE. N16 Engine: Oil Leak from Cylinder Head Sealing Plug. An oil leak can develop at a sealing plug located in the cylinder head, just below the vacuum pump. The sealing plug was not tightened sufficiently during production.
M1104142018-11-13. Service bulletin. ENGINE. N16 Engine: Oil Leak from Cylinder Head Sealing Plug. An oil leak can develop at a sealing plug located in the cylinder head, just below the vacuum pump. CAUSE The sealing plug was not tightened sufficiently during production.
M6401142018-11-13. Service bulletin. EQUIPMENT:APPLIANCE:AIR CONDITIONER. Automatic Deactivation of Recirculation Mode. The customer states the recirculation display goes out, even though the recirculation button was switched on. CAUSE The automatic recirculation air deactivation feature was introduced in July 2012. Note: If the customer dislikes this feature, it can be deactivated by using the following steps.
M5103142018-11-13. Service bulletin. VISIBILITY; EQUIPMENT. Transportation Protective Sleeve Introduced for Windshield Wipers. The windshield wipers streak and judder. The windshield wiper blades become distorted during transportation and when in storage.
M3401132018-11-13. Service bulletin. ELECTRICAL SYSTEM:SOFTWARE; SERVICE BRAKES, HYDRAULIC. Erroneous "Service due" Message Although Brake Lining Thickness is Above Minimum Specification. The yellow "Service Due" warning message lights up in the instrument cluster, even though the brake pad thickness is more than 4.2mm (above the thickness at which the pad sensor intervenes). The calculated remaining service life for the brake pads (front and/or rear axle) from the CBS data does not match the actual brake pad thickness. Software calculation of the brake pad wear model in the DSC.
M1201142018-11-13. Service bulletin. ENGINE AND ENGINE COOLING:EXHAUST SYSTEM. N16: Fault 274D Mixture Adaptation Is Stored in the DME. Certain low speed, light-load driving conditions at lower outside temperatures could cause the Service Engine Soon lamp (MIL) to illuminate. The following fault would be stored in the DME: Fault 274D: Mixture adaptation, lower engine speed range (mixture too lean) CAUSE 1. Possible intake/exhaust leaks, or a faulty component as listed in the test plan 2. Unfavorable DME software

The summaries are NHTSA's. Each bulletin's page links NHTSA's copy of the manufacturer's document.