WenmarOpen by Wenmar Pro

Service bulletins for the 2013 MINI Cooper Roadster

A bulletin is a manufacturer's communication to its dealers, as NHTSA indexes it. The summary is NHTSA's. The document is the manufacturer's: read it at NHTSA. A bulletin is not a recall, and listing a model year does not mean every vehicle of it is concerned.

103 on file from NHTSA, as of 2026-10-19.

By type

By component

By trouble code

Only bulletins with component: Engine are shown. Show all

Bulletins, newest first
M0104192020-02-18. Service bulletin. ELECTRICAL SYSTEM; ENGINE; FUEL SYSTEM, GASOLINE. CLASS ACTION SETTLEMENT: N14 HIGH-PRESSURE FUEL PUMP (HDP) SERVICE BENEFIT CLASS VEHICLES: The MINI vehicle may experience a sudden engine operational failure reduced or loss of power while driving and the malfunction indicator lamp (MIL) may be illuminated along with high-pressure fuel pumprelated faults stored in the Engine Control Module (DME). PROCEDURE Perform the corresponding diagnosis/vehicle test and run the test plans to completion as applicable.
M0102182019-05-20. Service bulletin. EQUIPMENT; EQUIPMENT ADAPTIVE/MOBILITY; ENGINE AND ENGINE COOLING. N18 THERMOSTAT WITH THERMOSTAT HOUSING: LIMITED WARRANTY EXTENSION TO 10 YEARS/ This Service Information bulletin supersedes SI M01 02 18 dated May 2018.
M0108172019-04-22. Service bulletin. ELECTRICAL SYSTEM; ENGINE. N16 ENGINE IGNITION COILS: LIMITED WARRANTY EXTENSION TO 10 YEARS/120000 MILES This Service Information bulletin supersedes SI M01 08 17 dated February 2018.
M1106122018-12-03. Service bulletin. ENGINE AND ENGINE COOLING. During Engine Oil Service a Small O-Ring Is Found in the Oil Filter Housing. No customer complaint has been received. During the scheduled engine oil service, the technician notices a black rubber o-ring lying on the bottom of the engine oil filter housing. The o-ring has been dislodged from the non-return valve inside the engine oil filter housing. No subsequent engine damage occurs from the dislodged o-ring. Engine oil filter housing (1) Rubber o-ring (2) The material dimensions of the rubber o-ring are not satisfactory, allowing it to become dislodged from its installation location.
M1201132018-12-03. Service bulletin. ENGINE AND ENGINE COOLING. N16 Engine: FC 2D9B Knock Sensor, Signal Is Stored in the DME. Certain areas of the US experience extremely cold climate conditions during the winter months, which can cause the Service Engine Soon lamp to illuminate while the engine temperature is increasing to full operating temperature. The following fault may be stored in the DME: ??FC 2D9B Knock Sensor, Signal CAUSE Unfavorable DME knock sensor diagnostic at outside ambient temperatures below -5° C
M1101122018-12-03. Service bulletin. ENGINE. The customer states that a small engine oil leak can be seen from the underside of the engine. CAUSE The internal sealing of the oil pump volume control solenoid valve is compromised, allowing engine oil to leak from the oil pump volume control solenoid.
M1103092018-11-26. Service bulletin. ENGINE. Whistling Noise from the Water Pump Area. A whistling or squealing noise is heard from the engine at idle and/or at higher engine speeds. CAUSE 1. Noise is caused by the water pump. 2. Noise is caused by the friction wheel of the belt tensioner.
M1202122018-11-26. Service bulletin. ELECTRICAL SYSTEM; ENGINE. SI M12 02 12 Engine Electrical Systems April 2013 Technical Service . After reprogramming the vehicle to integration level R056-11-11-503 (ISTA/P P45.1.3.0) or higher, one of the following fault codes are stored in the DME fault memory: Vehicles with N16 engine: * 2F42 Engine ventilation heating, Control The Service Engine Soon lamp is not illuminated. Vehicles with N18 engine: * 37DE Engine ventilation, heating, triggering: open circuit The Service Engine Soon lamp is illuminated. CAUSE Due to a DME software change, the diagnostic monitoring capability is improved for the engine ventilation heating system. However, a fault will be stored in the fault memory because the engine ventilation heater circuit has a malfunction currently present.
M1101132018-11-26. Service bulletin. ENGINE AND ENGINE COOLING. Service Action: Replace the Coolant Pump. Coolant is leaking from the coolant pump. CAUSE The coolant pump may develop cracks in the plastic housing. These cracks may result in a coolant leak.
M1101122018-11-26. Service bulletin. ENGINE. Engine Oil Leak. The customer states that a small engine oil leak can be seen from the underside of the engine. CAUSE The internal sealing of the oil pump volume control solenoid valve is compromised, allowing engine oil to leak from the oil pump volume control solenoid.
M1201132018-11-26. Service bulletin. ENGINE AND ENGINE COOLING. "N16 Engine: FC 2D9B Knock Sensor, Signal Is Stored in the DME. Certain areas of the US experience extremely cold climate conditions during the winter months, which can cause the Service Engine Soon lamp to illuminate while the engine temperature is increasing to full operating temperature. The following fault may be stored in the DME: FC 2D9B Knock Sensor, Signal While performing test plan B1214 M KNOCK SENSOR, the following error message will be displayed: ""An error has occurred during execution of a service program. Fault code: 61/3."" This error in the test plan will not allow diagnosis to continue. The test plan error will be repaired with ISTA/D 2.36.0. CAUSE A DME calibration error in the knock sensor diagnostics results in an increased sensitivity threshold to cold temperatures."
M1101122018-11-26. Service bulletin. ENGINE. Engine Oil Leak. The customer states that a small engine oil leak can be seen from the underside of the engine. CAUSE The internal sealing of the oil pump volume control solenoid valve is compromised, allowing engine oil to leak from the oil pump volume control solenoid.
M1104142018-11-13. Service bulletin. EQUIPMENT; ELECTRICAL SYSTEM; ENGINE. N16 Engine: Oil Leak from Cylinder Head Sealing Plug. An oil leak can develop at a sealing plug located in the cylinder head, just below the vacuum pump. The sealing plug was not tightened sufficiently during production.
M1104142018-11-13. Service bulletin. ENGINE. N16 Engine: Oil Leak from Cylinder Head Sealing Plug. An oil leak can develop at a sealing plug located in the cylinder head, just below the vacuum pump. CAUSE The sealing plug was not tightened sufficiently during production.
M1201142018-11-13. Service bulletin. ENGINE AND ENGINE COOLING:EXHAUST SYSTEM. N16: Fault 274D Mixture Adaptation Is Stored in the DME. Certain low speed, light-load driving conditions at lower outside temperatures could cause the Service Engine Soon lamp (MIL) to illuminate. The following fault would be stored in the DME: Fault 274D: Mixture adaptation, lower engine speed range (mixture too lean) CAUSE 1. Possible intake/exhaust leaks, or a faulty component as listed in the test plan 2. Unfavorable DME software
M1101122018-11-13. Service bulletin. EQUIPMENT; ENGINE; EQUIPMENT ADAPTIVE/MOBILITY. N16 and N18 Engine Oil Leak. The customer states that a small engine oil leak can be seen from the underside of the engine. CAUSE The internal sealing of the oil pump volume control solenoid valve is compromised, allowing engine oil to leak from the oil pump volume control solenoid.
M2101142018-11-13. Service bulletin. ENGINE AND ENGINE COOLING:ENGINE:DIESEL; POWER TRAIN. Dual Mass Flywheel: Diagnosis and Inspection. INFORMATION The following three criteria must to be checked, evaluated and the resulting findings documented on the repair order prior to replacing a dual-mass flywheel as defective: 1. Total rotational angle at no load condition (with applied torque less then 20 Nm) 2. Secondary plate longitudal axial play 3. Friction surface appearance changes due to thermal overload. PROCEDURE Refer to the attached "Dual-mass Flywheel Inspection" document for the complete inspection procedure. The dual-mass flywheel replacement is justified only if one or more of the following criteria are met: 1. The total rotational free-play measured at the flywheel gear ring is: Equal to or greater than 3 tooth gaps on N14/N18-equipped engines; Equal to or greater than 14 tooth gaps on B38/B46/B48-equipped engines. 2. The secondary plate total axial bearing play measured at outside diameter of the flywheel is: Equal to or greater than 3 mm on N14/N18-equipped engines; Equal to or greater than 5 mm on B38/B46/B48-equipped engines. 3. Significant discoloration in the adjoining area outside the friction ring, or a severe ablation/erosion of the friction area, is present. WARRANTY INFORMATION Warranty claims for replacing a Dual Mass Flywheel are subject to denial or debit when it is determined that the diagnostic procedures outlined above were not followed. ATTACHMENTS View PDF attachment M210114_Dual-Mass_Flywheel_Inspection.
M1301142018-11-13. Service bulletin. ENGINE; FUEL SYSTEM, GASOLINE. "N14 and N18 Engine: High-pressure Pump Repair Instruction. INFORMATION The current version of ISTA/D Repair Instruction 13 51 017, ""Removing and installing or replacing high-pressure pump (N14, N18)"" has a procedure error. The current version of the Repair Instruction states to replace the high-pressure supply hose on the N14 engine. The Repair Instruction also states not to replace the high-pressure supply hose on the N18 engine. The N18 portion of the Repair Instruction is incorrect. As an interim solution, follow the procedure outlined below until this portion of the Repair Instruction is corrected. https://www.minitis.net/tiscode/cgi-bin/bulletin.aspx?sie_path=/tsb/bulletins/htm_store/159...2/5/2014 Page 2 of 2 Bosch High-pressure Pump (1): All vehicles equipped with the N18 engine and produced from 3/2012 and later When the engine is fitted with a Bosch High-pressure Pump (1), the highpressure supply hose (2) MUST NOT be replaced when making repairs. The remaining portion of the Repair Instruction and tightening torques is correct. Refer to EPC for the applicable part numbers when making repairs."
M1201142018-11-13. Service bulletin. ELECTRICAL SYSTEM; ENGINE. N16: Fault 274D Mixture Adaptation Is Stored in the DME. Certain low speed, light-load driving conditions at lower outside temperatures could cause the Service Engine Soon lamp (MIL) to illuminate. The following fault would be stored in the DME: ??Fault 274D: Mixture adaptation, lower engine speed range (mixture too lean) CAUSE 1. Possible intake/exhaust leaks, or a faulty component as listed in the test plan 2. Unfavorable DME software.
M1101122018-11-13. Service bulletin. ENGINE; ELECTRICAL SYSTEM. "N16 and N18 Engine Oil Leak. The customer states that a small engine oil leak can be seen from the underside of the engine. CAUSE The internal sealing of the oil pump volume control solenoid valve is compromised, allowing engine oil to leak from the oil pump volume control solenoid. DIAGNOSTIC Below is the procedure for identifying how far the engine oil has migrated inside the engine electrical harness, when this issue occurs, if at all. The procedure must be followed very carefully so that the proper repair is identified. 1. Disconnect the oil pump volume control solenoid valve electrical connection per Repair Instructions 11 41 519 ""Removing and installing or replacing the solenoid valve (engine oil pump)."" Inspect the electrical connector; if no engine oil is found inside the electrical connector, perform the oil pump volume control valve repair procedure. If engine oil is found inside the electrical connector, proceed to diagnostic procedure step 2. 2. Remove the cover from the DME and remove all three electrical connectors from the DME. Inspect the connectors for traces of engine oil. If no engine oil is found, perform the oil pump volume control valve repair procedure and replace the engine section of the wire harness. Refer to EPC for the additional part number. If engine oil is found in the DME connector, proceed to step 3. 3. If engine oil is found in the DME electrical connector, perform the oil pump volume control valve repair procedure, replace the engine section of the wire harness and replace the DME. Refer to EPC for the additional part numbers. Do not remove the engine oil pan. Do not replace the oil pump volume control valve. Do not replace engine oil pump. OIL PUMP VOLUME CONTROL VALVE REPAIR"
M1108152018-11-13. Service bulletin. ENGINE. Surface Cracks on the Water Pump Drive Pulley. During a repair, service or inspection, the drive pulley on the water pump shows signs of cracking. No part replacement is necessary unless there is another issue found that will be corrected by replacing the drive pulley.
M6402152018-11-13. Service bulletin. VISIBILITY:DEFROSTER/DEFOGGER/HVAC SYSTEM:FAN/MOTOR; ENGINE AND ENGINE COOLING. The Blower Motor is Faulty. The blower motor does not operate at any fan speed. The blower motor may work intermittently with the blower fan speed operating only on FULL speed. CAUSE The blower motor is faulty and causes the blower resistor to fail.
M1701152018-11-13. Service bulletin. ENGINE AND ENGINE COOLING; ENGINE. "Engine Cranks, No Start and/or Engine Coolant Temperature Faults. 1 The engine either exhibits a crank, no start or a hard start (long crank), usually on a cold engine. No faults are stored in the DME. Proceed to Correction 1 for further diagnosis. 2 NOTE: The engine may also exhibit the same starting behavior as in Situation1. The Service Engine Soon lamp is illuminated, with one or more of the following fault codes stored in the DME: Engine temperature sensor faults ? 2943 Coolant temperature sensor, signal change too fast ? 2937 Coolant temperature sensor, electrical: short circuit to positive ? 2936 Coolant temperature sensor, electrical: short circuit to earth ? 293A Coolant temperature sensor, plausibility, cold start: temperature too high ? 293B Coolant-temperature sensor, plausibility, cold start: Temperature too low ? 2947 Coolant-temperature sensor, signal: Fixed on low ? 2948 Coolant-temperature sensor, signal: Fixed ? 3393 Engine downtime, plausibility: Time too long in correlation with engine coolant cooling down ? 3392 Engine downtime, plausibility: Time too short in correlation with engine coolant cooling downIf any of the above fault codes are stored, proceed to Correction 2. Engine thermostat faults: ? 348E Characteristic map thermostat, actuation: Short circuit to positive ? 348F Characteristic map thermostat, actuation: Short circuit to earth ? 3490 Characteristic map thermostat, actuation: Open circuit If any of the above fault codes are stored then proceed to Correction 2: The above fault codes for the engine temperature sensor and thermostat are the primary fault codes for turning the Service Engine Soon light on. 1. Poor solder contacts in the engine coolant temperature sensor integrated into the engine thermostat housing 2. A faulty external or replaceable engine coolant temperature sensor (see below for identifying production changes in the thermostat and engine temperature sensors) 3. A faulty map-contro
M1201152018-11-13. Service bulletin. ELECTRICAL SYSTEM; ENGINE. Engine Misfire Due to Failed Ignition Coil. ? The Check Engine or Service Engine Soon (MIL) lamp is on with misfire fault(s) stored in the DME. ? Intermittent performance or rough running without a relevant DME fault stored The most likely cause is that an ignition coil has failed, which in many cases can be confirmed with basic diagnosis. During operation with high temperature fluctuations, the different materials used in the Bosch ignition coil construction can deteriorate over time, leading to a failure.
M1209152018-11-05. Service bulletin. ENGINE; FUEL SYSTEM, GASOLINE. Intermittent Poor Throttle Response at High Ambient Temperatures. The engine throttle response from a stop can intermittently be sluggish when the outside ambient temperatures are higher. Additionally, this can be more noticeable when the fuel tank is only partially filled. CAUSE DME software for fuel tank ventilation control

The summaries are NHTSA's. Each bulletin's page links NHTSA's copy of the manufacturer's document.