Service bulletins for the 2024 Mercedes-Benz eSprinter
A bulletin is a manufacturer's communication to its dealers, as NHTSA indexes it. The summary is NHTSA's. The document is the manufacturer's: read it at NHTSA. A bulletin is not a recall, and listing a model year does not mean every vehicle of it is concerned.
13 on file from NHTSA, as of 2026-10-19.
By type
By component
By trouble code
Only bulletins with component: Engine are shown. Show all
| LI49.20-N-079157 | 2025-05-02. Service bulletin. ENGINE. Check engine light with possible Adblue warning with fault code P20F409 or P202E84 Complaint The check engine light is activated, accompanied by one or more of the following fault codes related to the Adblue System: •P20F409: The Adblue consumption is too low. There is a component fault. •P202E84: The Adblue metering valve 1 (Motor side) has a malfunction. There is a signal below the permissible limit value. Cause The potential causes for these fault codes are: A. A leak in the Adblue System B. An internal fault with the Adblue Injection Valve #1 (Motor side) C. An air pocket forming in the Adblue Injection Valve #1 (Motor side) Adblue Injector Line Remedy --Prior To Production Date 08/01/2024-- A. A Leak in the Adblue System 1. Complete the Guided Tests for P20F409 or P202E84: •Perform a thorough inspection of the Adblue Tank, the Adblue Pump, the Adblue Line, and both Adblue Injectors for leaks. •Ensure the Adblue line is properly installed, securely fastened in all clips, and not in contact with the exhaust system. •Remove both Adblue Injection Valves and complete 2-3 pressure build-ups and inspect for Adblue leakage. •If a leak is identified, repair it and retest. |
|---|---|
| LI09.41-N-079165_1 | 2025-05-02. Service bulletin. ENGINE. Low Coolant Warning, Potential Misfire, and Absence of External Coolant Leaks Complaint Low Coolant warning with possible engine misfire caused by a leaking Charge Air Cooler (Intercooler), accompanied by one or more of the following possible fault codes related to the coolant system: P30040B: Component 'Temperature sensor downstream of charge air cooler' has an open circuit or short circuit to po- sitive. P25567B: Sensor 'Coolant level' has a malfunction. The fluid level is too low. Cause The potential causes for this topic are: A. A leak in the Coolant System, other than the Charge Air Cooler. B. An Internal leak of the Charge Air Cooler. C. An unapproved/aftermarket upfit or modification to the coolant system. Remedy A. A leak in the Coolant System, other than the Charge Air Cooler 1. Complete a coolant system pressure test: •Refer to WIS Doc AR20.00-D-1011TS - Check engine cooling system for leak tightness. •Use Tester Cap 210 589 00 91 and Pressure Pump 124 589 24 21 00. •Apply test pressure to the engine cooling system. Do not exceed the specified test pressure of 1.5 Bar to prevent da- mage to the engine cooling system. •Perform a visual check on the top and bottom of the engine compartment and in the vehicle interior. •If coolant loss or pressure loss is present, perform suitable repair measures depending on the vehicle equipment. •If NO signs of coolant loss are found but pressure loss is present, proceed to Step B. |
| LI09.40-N-079144_4 | 2025-05-02. Service bulletin. ENGINE. Check engine light with reduced power with fault codes P300A6D, P300974, P300DFB, or P300DE8 Complaint: The check engine light is activated, accompanied by one or more of the following fault codes related to the Boost Pressure Positioner: • P300A6D The boost pressure is too low. Charge Air Cooler. • P300974 Component 'Boost pressure positioner' has a malfunction. The boost pressure is too low. • P300DFB Component 'Boost pressure positioner' has a malfunction. • P300DE8 Boost pressure control A has a malfunction after the cold start. Cause: The potential causes for these fault codes are: A. Leak or Blockage in the Intake or Charge Air System: This can prevent the proper flow of air, affecting the boost pressure. B. Insufficient Source Vacuum, Vacuum Leak, or Sticking/Weak Vacuum Component: These issues can prevent the boost pressure positioner from functioning correctly. C. Internal Malfunction of the Boost Pressure Positioner: The component itself may be faulty. D. Internal Defect with the Variable Turbine Geometry (VTG) System inside the Turbocharger: Issues within the turbo-charger can affect boost pressure control. |
| LI14.30-N-075882 | 2024-11-05. Service bulletin. ENGINE. Complaint Check engine warning light active. Fault code P300CA8 or P300CA9 "Hot film mass air flow sensor malfunction" present in engine control unit. Cause These faults can be set if: 1. A leakage upstream of the exhaust gas turbocharger causing a to high EGR rate. 2. Carbonized parts, e.g., the intake module, housing intermediate flange on high-pressure EGR valve (assembly of exhaust pressure sensor P3) or the intake ports also let through too little air. 3. The air filter has been highly soiled, incorrectly positioned or has a deformation. |
The summaries are NHTSA's. Each bulletin's page links NHTSA's copy of the manufacturer's document.