Recalls that may apply to the 2008 Mercedes-Benz C-Class
A recall listed here may apply to a vehicle of this year, make and model. Only the manufacturer can say whether it applies to one vehicle: check the VIN with the official lookups.
By component
| 07V465000 | 2007-10-03. SEAT BELTS:REAR/OTHER. CERTAIN VEHICLES FAIL TO COMPLY WITH SOME OF THE REQUIREMENTS OF FEDERAL MOTOR VEHICLE SAFETY STANDARD NO. 208, "OCCUPANT CRASH PROTECTION." THE REAR OUTBOARD SEAT BELTS DO NOT COMPLY WITH THE LAP-BELT LOCKABILITY REQUIREMENT WHICH ENABLES THE LAP BELT PORTION OF THE BELT TO BE LOCKED BY THE USER TO FACILITATE THE USE OF OLDER NON-LATCH DESIGN CHILD RESTRAINT DEVICES. Built 2007-05-01 to 2007-08-31. |
|---|
| 2022127 | 2022-03-18. Electrical. Issue: During servicing at a dealership, a small number of vehicles may have received an incorrect software update to one or more control units. As a result, the electronic stability control system, exterior lighting, and engine power could be affected. Safety Risk: Safety systems that don't work correctly could increase the risk of a crash. Corrective Actions: Mercedes-Benz will notify owners by mail and instruct you to take your vehicle to a dealership to update the software in the control module(s). |
|---|---|
| 2017017 | 2017-01-11. Airbag. On certain vehicles, long-term exposure to high absolute humidity and temperature, combined with high temperature cycling, could eventually degrade the propellant contained in the passenger frontal airbag. This could cause the airbag to deploy with more force than normal. As a result, if the vehicle were involved in a collision that warrants airbag deployment, fragments could be propelled toward vehicle occupants, and the airbag assembly could be damaged, preventing proper function. These issues could increase the risk of injury. Correction: Dealers will replace the passenger frontal airbag module. Note: Canadian climate results in the propellant degrading slowly. The recall is being conducted as a precaution to address future risk, and is expected to replace airbag inflators before their function would be affected. |
| 2016158 | 2016-04-13. Airbag. On certain vehicles, the driver frontal airbag inflator could produce excessive internal pressure during airbag deployment. Increased pressure may cause the inflator to rupture, which could allow fragments to be propelled toward vehicle occupants, increasing the risk of injury. This could also damage the airbag module, which could prevent proper deployment. Failure of the airbag to fully deploy during a crash (where deployment is warranted) could increase the risk of personal injury to the seat occupant. Correction: Dealers will replace the front driver air bag module. |
| 2015505 | 2015-10-23. Airbag. On certain vehicles, a defect in the supplemental restraint system (SRS) controller could result in the inadvertent deployment of SRS components, such as airbags and seatbelt pretensioners, or could cause these components to fail to deploy in a crash where deployment is warranted. Unintended seatbelt pretensioner, airbag or other deployment, in a non-warranted (non-impact) situation, could result in minor injuries and could also startle the driver, which could result in a vehicle crash. Additionally, failure of the SRS components to deploy in a crash could increase the risk of injury. Correction: Dealers will replace the SRS control unit. Note: This condition would cause the illumination of the SRS warning light. |
| 2014132 | 2014-04-14. Lights And Instruments. On certain vehicles, oxidation on the ground pin connector for the rear tail lamps may cause a dimming or loss of one or more rear lamp functions (tail, brake, turn signal). Failure of any rear lamp function may result in the following road users being unaware of the driver's intentions, as well as reducing vehicle conspicuity during hours of darkness. Correction: Dealers will inspect and if necessary replace the rear tail lamps on affected vehicles. |
| 2008242 | 2008-07-09. Other. Certain vehicles may have been programmed with incorrect software calibration data during the manufacturing process. This could affect various functions such as: The electric fuel pump may not receive a signal which, in case of a crash, may prevent the fuel pump from disconnecting as designed; The maximum speed limiter may not be activated; The fuel gauge readings may be incorrect; A stuck fuel-level sensor may not be displayed in the instrument cluster; The speedometer may be out of tolerance which, as a result, may indicate inaccurate vehicle speed; The On-Board Diagnostic (OBD) system may reduce the emission level applicable to the vehicle, causing the Check Engine Light to illuminate incorrectly. Correction: Dealers will reprogram the electronic control module. |
| 2007332 | 2007-10-12. Seats And Restraints. Certain vehicles fail to comply with the requirements of CMVSS 208 - Occupant Restraint Systems. The rear outboard seat belt locking mechanism may not perform as designed for the use with older non-LATCH child restraints. When using the newer LATCH equipped child restraints, the rear seatbelt is not utilized. Correction: Dealers will replace the rear outboard seatbelt assemblies. |
A campaign lists a year, a make and a model, and often only some of the vehicles built. A list with nothing on it is not a clearance either. The lookups below check one VIN.
Check one vehicle officially
Contains information licensed under the Open Government Licence – Canada.