Service bulletins for the 2019 Mercedes-Benz AMG GT
A bulletin is a manufacturer's communication to its dealers, as NHTSA indexes it. The summary is NHTSA's. The document is the manufacturer's: read it at NHTSA. A bulletin is not a recall, and listing a model year does not mean every vehicle of it is concerned.
242 on file from NHTSA, as of 2026-10-19.
By type
By component
By trouble code
By topic
| LI82.85-P-079271 | 2025-05-29. Service bulletin. ELECTRICAL SYSTEM. Complaint After a software update of HERMES communication module N112/9 has been performed on a gray import vehicle, the message "SOS - Service not activated" is displayed in the instrument cluster. Cause The message "SOS - Service not activated" tells the customer that "over-the-air" registration of the vehicle with the Mercedes Intelligent Cloud is not possible. On a gray import vehicle, this is due to the fact that the SIM card installed in the HERMES communications module cannot dial into the mobile phone network in the importing country. Remedy The only way of avoiding the message in the instrument cluster is to deactivate the HERMES module using the 09o deactivation process after obtaining the customer's consent. After deactivation, the HERMES control unit (N112/9) has the operating status "Inoperative". The message "SOS not ready" appears in the audio/COMAND display (A40/8) and may also appear in the instrument cluster. This display message tells the customer that the emergency call function is not available. In addition, the workshop must attach a label (2 x part number A9078172900 required) to the cover of the emergency call button in the overhead control panel and to the emergency call button itself. Replacing the hardware of the HERMES communication module is not effective. |
|---|---|
| EW - Tank Leakage | 2025-05-28. Warranty extension. FUEL/PROPULSION SYSTEM. In our continuing efforts to ensure the proper performance of Mercedes-Benz products and to enhance the satisfaction of our customers, Mercedes-Benz USA, LLC (“MBUSA”) is extending the warranty coverage on the Diagnostic Module for Tank Leakage detection (DMTL) in certain Model Year (“MY”) vehicles listed below from the original New Vehicle Limited Warranty of 4 years/50,000 miles to 10 years/120,000 miles (vehicles certified as LEV II) and 15 years/150,000 miles (vehicles certified as LEV III), whichever occurs first, for the following condition: • Under certain circumstances, the DMTL may trigger erroneous Diagnostic Trouble Code (DTC) entries that may result in the illumination of the Check Engine Malfunction Indicator Lamp (‘MIL’). |
| NCU-2025050001 | 2025-05-09. Emissions. ELECTRICAL SYSTEM. Mercedes-Benz AG, the manufacturer of Mercedes-Benz vehicles, has determined that certain Model Year (“MY”) 2019 – 2022 C-Class, CLS, E-Class, E-Class Coupe/Convertible, GLE/GLS-Class and AMG GT vehicles (206, 257, 213, 238,167 and 290 platforms) are potentially affected with multiple topics related to the 48V battery management system, which erroneously may or may not illuminate the check engine malfunction indicator lamp (‘MIL’) in one or more of the following circumstances: • Memory error causing battery switch to open, prohibiting vehicle to restart; • The battery thermal management system, power supply voltage (12V) measurement and 48V battery switch diagnostic may not be monitored by the OBD-system; • Plausibility check of the temperature sensor, temperature range and Real Time Clock (RTC) monitoring might not operate as intended. MBUSA will conduct an Emission Service Campaign. An authorized Mercedes-Benz dealer will update the drivetrain control unit software on the affected vehicles. Affected customers will be notified via First Class letter to have the update performed on their vehicle. |
| LI82.85-P-078303 | 2025-05-06. Service bulletin. ELECTRICAL SYSTEM. Complaint Individual functions such as sliding sunroof or roller sunblind can no longer be operated using the gesture recognition system. Cause Gesture recognition system control unit software N168 Remedy For vehicles before modification year 23/2: Perform SCN coding in control unit OMSH223 (N168). For vehicles as of modification year 23/2: Considered to be a series production configuration. A change will not be possible in future. NOTE: The information contained in this document is intended for use by trained, professional technicians with the knowledge to properly and safely perform diagnosis and repairs on Mercedes-Benz vehicles, using Mercedes-Benz approved tools and equipment. It informs service technicians about conditions that could occur in certain vehicles and provides information that could assist in proper vehicle diagnosis, service, or repair. It does not indicate that a defect is present in any vehicle referenced in this document nor does it imply warranty coverage. DO NOT assume that a symptom or condition, or a described cause of a symptom or condition, affects any particular vehicle or groups of vehicles, or that a described repair applies to any particular vehicle or groups of vehicles. There can be multiple causes resulting in the same or similar symptoms or conditions described in this document, and trained professional service technicians must use their diagnostic skills to make evaluations on a case-by-case basis. The information contained in this document does not guarantee warranty coverage nor does it extend the vehicle’s warranty in any way. |
| LI82.10-P-078896 | 2025-05-02. Service bulletin. EXTERIOR LIGHTING. Complaint Headlamps leaking or fogged Cause The fogging of the headlamp is a natural phenomenon which can occur under certain climatic conditions. In contrast to a leaky headlamp, physical fogging does not result in a technical impairment of the headlamp. A leak test must be performed to determine if physical fogging exists or if the headlamp is leaky. Remedy Check for external damage: You can identify a damaged headlamp in the following way: For headlamps with a closed system 1. Check the headlamps for any external damage and check also for correct seating of the Gore-diaphragm/correct latching of the cover caps. 2. If the headlamp exhibits any external damage, replace the headlamp. For headlamps with an open system 1. Check the headlamps for any external damage and seal off the vent, then make sure the cover caps are latched correctly into place. 2. If the headlamp exhibits any external damage, replace the headlamp. Note: External damage to the headlamp does not present a warranty or goodwill case. 1. Clear fogged/condensed LED headlamps and LED rear lamps: 1. Drive the vehicle into the workshop (temperature higher than +18 °C/+64.4°F). Note: Do not perform an engine wash before the defogging test. 2. Switch off the engine and connect battery support via a charger. 3. Open the hood or trunk. 4. Switch on the lights. 5. Leave the vehicle in this state for 60 minutes. 6. Check for formation of condensation, a significant reduction in the formation of condensation must be clearly recognizable (thawing progress). 7. If the condensation has disappeared, nothing else has to be done. Note: If defrosting has been performed, you can skip the first step. 2. Leak test of headlamp with overpressure: • Connect test adapter to pressure tester. (Figure 1) • Check test adapter for leak tightness. To do so, connect plug and coupling (picture 2) and apply a maximum overpressure of 30 mbar. The pressure must remain constant. If the pressure does not remain constant, use a new adapter. • All vents have to be sealed with sealing compound and the existing diaphragm with the stamp (picture 3 [3]). (Picture 4) Make allowance for the different headlamp variants here (there are different outlet openings). • Check if the headlamp needs to be removed to gain access to the diagnostic socket on the headlamp housing. • Plug the adapter onto the diagnostic socket on the headlamp housing. (Picture 5). • Apply a maximum of 30 mbar overpressure to the headlamp housing. Note: If the maximum overpressure of 50 mbar is exceeded the headlamp seal will be damaged (picture 6). • If a pressure drop of less than 10 mbar is measured within 30 seconds, the headlamp is tight and there is natural physical condensation. • If a higher pressure drop than 10 mbar is measured within 30 seconds, the headlamp is leaky. Note: The leaky position can be localized with the aid of soap suds. If the pressure test is not passed, the headlamp is leaky. If the cause cannot be rectified, the headlamp must be replaced. Note: If the headlamp is replaced, no dry packs may be installed on the new replacement headlamp. AR82.10-P-5455WT was created for the pressure test. This AR can be used as a reference manual for all closed headlamps. In the event of an open headlamp system, the vent ducts must be sealed before the pressure test. |
| LI82.10-P-078301 | 2025-05-02. Service bulletin. EXTERIOR LIGHTING. Complaint Headlamp, front fog lamp leaky or fogged Cause Fogging of the headlamps is a natural phenomenon, which can occur under certain climatic conditions. It does not lead to any technical impairment of the headlamp. Remedy NOTE: If a pressure compensation diaphragm is fitted in the housing cover, then the lamp unit is a "closed system". Headlamp: Remedy 1 Clearing fogged/condensed LED headlamps and LED rear lamps: 1. Drive vehicle into workshop (temperature higher than +18 °C/+64.4 °F) and connect the exhaust extraction. Note: Do not perform an engine wash before the defogging test. 2. Switch off the engine and connect battery support via a charger. 3. Open the hood or trunk. 4. Switch on the lights. 5. Leave the vehicle in this state for 60 minutes. 6. Check for formation of condensation, a significant reduction in the formation of condensation must be clearly recognizable (thawing progress). Clearing fogged/condensed halogen/xenon headlamps: 1. Drive the vehicle into the workshop (temperature higher than +18 °C/+64.4°F). Note: Do not perform an engine wash before the defogging test. 2. Switch off the engine. 3. Open the hood. 4. Switch off the lights. 5. Leave the vehicle in this state for 60 minutes. 6. Check for formation of condensation, a significant reduction in the formation of condensation must be clearly recognizable (thawing progress). Note: If there is no visible reduction in the formation of condensation, check the headlamp for damage. (See Remedy 2) It is not physically possible to defog the headlamps completely. Fogging does not impair the operation or the service life of the headlamp. Remedy 2 A damaged headlamp can be identified as follows: 1. Check the headlamp for external damage and that the cover caps and the diaphragm are correctly seated. 2. Check the electrical connectors of the plugs and pins. 3. Check for leak tightness in accordance with LI82.10-P-078896 The test can only be conducted on headlamps. 4. If the headlamp or the rear lamp has any external damage, replace the component part in accordance with the WIS instructions. |
| LI42.10-P-063502 | 2025-04-25. Service bulletin. SERVICE BRAKES. Complaint Noises/ squealing from the service brake in various driving situations and ambient conditions. Cause Frictional vibrations Remedy AMG brake systems are designed for high loads. This can result in noises under certain operating conditions and driving styles. Please refer to the Operator's Manual for further information such as care and maintenance instructions (washing vehicle directly after heavy use and using approved cleaning agents). These are dependent on speed, brake pressure or ambient conditions such as temperature and air humidity. 1. Beginning Diagnostics: a) Check whether the complaint can be reproduced and at which axle or side the noises occur (ideally together with the customer while driving). b) Check the affected system for component wear, mechanical damage or localized overheating damage. Replace damaged components as necessary. c) Assess condition of brake rotors and pads per WIS and visually (i.e. long periods of stagnation, etc...). d) Clean brake components free of brake dust and debris. d) Secure vehicle on a lift. 1. Start the engine and depress the brake pedal 3-4 times. 2. Check each wheel to see if they turn freely by hand. 3. If a wheel is not turning freely by hand, this needs to be addressed prior to re-assessing the noise concern. e) Check whether, apart from this document, an additional document exists for the specific model in question, and if so, work through it and then continue. 2. Specific Axle Work: NOTE: If the brake pad has a metal backing plate, there is no need to affix the adhesive film. a) If the noises are coming from the front axle => Affix linings with adhesive film (see attachments for front axle). If backing plate is installed on pads, move to step 3. 1. Remove brake linings of front axle. 2. Clean all contact points on brake lining and brake caliper/carrier. 3. Clean bonding surface (where pistons contact back of brake pad). Apply adhesive film to the backplate of the piston-side brake lining where the piston contacts the pad backing plate. See picture "Adhesive and Paste Application Area". 4. Chamfer edges (round off sharp leading edges) on brake pads. See picture "Chamfered Pads". 5. Apply heat-resistant lubricating paste to the sides of the backing plate. See picture "Adhesive and Paste Application Area". 6. After installing the brake linings, actuate the brake for 30 seconds. b) If the noises are coming from the rear axle => Affix linings with adhesive film and grease the lining as per the specification (see attachments for rear axle). 1. Remove brake pads of rear axle. 2. Cleaning all contact points on brake lining and brake caliper/carrier. 3. Grease contact points (red areas) between brake lining and guide of brake caliper with heat-resistant lubricating paste. 4. Clean bonding surface (where pistons contact back of brake pad). Apply adhesive film to the backplate of the piston-side brake lining. 5. Chamfer edges (round off sharp leading edges) on brake pads. See picture "Chamfered Pads". IMPORTANT: Be absolutely certain to not allow paste between friction surfaces of the pad and disc! 3. Brake Bedding Process: a) Before trip, the mileage incurred must be clarified with the customer (approx. 30 miles). b) Select a suitable route so speeds of approximately 65 MPH can be achieved. c) If the vehicle is an AMG P3 Hybrid, switch off recouperation prior to bedding in brakes. d) Brake the vehicle 15 times with a brake pressure of approx. 30 bar (have the passenger read it out using XENTRY) from 62 MPH to 30 MPH (no emergency stops and no braking in the ESP control range). Maintain a cooling distance of approx. 1 mile between brake applications. e) Finally drive approx. 3 miles to allow the system to cool. f) Reassess noise. |
| LI54.71-P-078802 | 2025-04-01. Service bulletin. ELECTRICAL SYSTEM. Complaint MBUX head unit display with red text box "System Inoperative". ONLY for vehicles with SA code (549+21U) or (549+U19). Cause Head unit software variant. Remedy For all chassis use Xentry to update head unit (A26/17). Target boot software number should be either: • 247 904 6600 (E905.4) OR • 247 904 7500 (E906.1) If vehicle fits all criteria and either target software is not available via Xentry, please open an XSS ticket. |
| LI27.35-P-079039 | 2025-03-27. Service bulletin. POWER TRAIN. Complaint A clicking/ticking/taping noise from underneath the vehicle with engine off during ECO stop event or after parking See video for example Cause Noise originates within the transmission valvebody Remedy Take a video from underneath vehicle recording the noise Pull EEPROM data, Inital Quick Test, and Control Unit Log Please open a TIPs case providing all data to assess next steps. |
| LI82.70-P-077433 | 2025-03-17. Service bulletin. ELECTRICAL SYSTEM. Complaint During a phone call, the called party has difficulty understanding/cannot understand the driver, or interference/background noises are audible to the called party during a call. It becomes increasingly difficult to understand as the speed rises. Cause A. Seating of the microphones in the headliner. Side edges are covered by the textile cover (see picture "1") B. Assembly of microphones (B25/20 or B25/21) in the headliner. C. Dirt inside the microphone housing Remedy 1. Press finger on rear of microphone (on adhesive tape) 2. Remove microphone cap from the front 3. Eliminate protruding material residues of the microphone cutout at the headliner, e.g. with a soldering iron. The microphone must be seated in the headliner as shown in picture "2". 4. Push microphone from behind until it is firmly pressed into the headliner 5. Maintain pressure and press/clip cap into microphone from the front. Note: The cover cap must be clearly heard and felt to engage. 6. This procedure must be carried out on both microphones (B25/20 and B25/21) Note: • It is recommended to replace the cover caps. • The non-woven cloth in the cover cap protects the microphone from soiling and must not be removed. NOTE: The information contained in this document is intended for use by trained, professional technicians with the knowledge to properly and safely perform diagnosis and repairs on Mercedes-Benz vehicles, using Mercedes-Benz approved tools and equipment. It informs service technicians about conditions that could occur in certain vehicles and provides information that could assist in proper vehicle diagnosis, service, or repair. It does not indicate that a defect is present in any vehicle referenced in this document nor does it imply warranty coverage. DO NOT assume that a symptom or condition, or a described cause of a symptom or condition, affects any particular vehicle or groups of vehicles, or that a described repair applies to any particular vehicle or groups of vehicles. There can be multiple causes resulting in the same or similar symptoms or conditions described in this document, and trained professional service technicians must use their diagnostic skills to make evaluations on a case-by-case basis. The information contained in this document does not guarantee warranty coverage nor does it extend the vehicle’s warranty in any way. |
| LI09.41-P-078735 | 2025-03-11. Service bulletin. ENGINE. Complaint Check engine light illuminated Fault code present in MRG3 control unit P22C800 or P22C900 - The valve of the exhaust gas turbocharger is jammed. Cause Check valve in charge air pipe jammed. Remedy Replaced charge air line with check valve. |
| OTA- 24P5497747 | 2025-02-28. Over-the-air update. ELECTRICAL SYSTEM. Mercedes-Benz AG, the manufacturer of Mercedes-Benz vehicles, has determined that on certain MY19-25 A-Class, C-Class, CLA, CLS, E-Class, G-Class, GLA, GLB, GLC, GT, and S-Class (118, 177, 205, 213, 217, 222, 238, 247, 253, 257, 290, 463 platform) vehicles, the communication software does not correspond with the latest series production configuration. The communication module will receive an OTA update which includes quality-enhancing optimizations and improves the system stability and accessibility of Mercedes me services. The update is downloaded and installed in the background. During installation, the system can be used without restrictions. The new software will become active after the vehicle has been restarted. MBUSA will conduct an OTA service campaign. Remote software updates are automatically downloaded and installed in the customer’s vehicle free of charge and do not require a dealer visit. No customer letter will be mailed for this OTA software update. Parts Parts are not required |
| LI54.71-P-078802 | 2025-02-28. Service bulletin. ELECTRICAL SYSTEM. Complaint MBUX headunit display with red text box "System Inoperative". ONLY for vehicles with SA code (549+21U) or (549+U19). Cause Under analysis. Remedy For chassis 118, 167, 177, 213, 238, 243, 247, 253, and 293 use Xentry to update headunit (A26/17). Target software number is 247 904 6600 (E905.4). |
| LI42.10-P-063502 | 2025-02-22. Service bulletin. SERVICE BRAKES. Complaint Noises/ squealing from the service brake in various driving situations and ambient conditions. Cause Frictional vibrations Remedy AMG brake systems are designed for high loads. This can result in noises under certain operating conditions and driving styles. Please refer to the Operator's Manual for further information such as care and maintenance instructions (washing vehicle directly after heavy use and using approved cleaning agents). These are dependent on speed, brake pressure or ambient conditions such as temperature and air humidity. 1. Beginning Diagnostics: a) Check whether, apart from this document, an additional document exists for the model series in question, and if so, work through it and then continue with1b. b) Check whether the complaint can be reproduced and at which axle or side the noises occur (ideally together with the customer while driving). c) Check the affected system for component wear, mechanical damage or localized overheating damage. 1. Replace damaged components as necessary and re-assess noise concern. d) Secure vehicle on a lift. 1. Start the engine and depress the brake pedal 3-4 times. 2. Check each wheel to see if they turn freely by hand. 3. If a wheel is not turning freely by hand, this needs to be addressed prior to re-assessing the noise concern. e) Assess condition of brake rotors and pads per WIS and visually (i.e. long periods of stagnation, etc...). 2. Specific Axle Work: NOTE: If brake pad has a metal backing plate, there is no need to affix the adhesive film. a) If the noises are coming from the front axle => Affix linings with adhesive film (see attachments for front axle). If backing plate is installed on pads, move to step 3. 1. Remove brake linings of front axle. 2. Clean all contact points on brake lining and brake caliper/carrier. 3. Clean bonding surface (where pistons contact back of brake pad). Apply adhesive film to the backplate of the piston-side brake lining. For 6 piston calipers, only in the area of the center piston. For other piston caliper configurations less than 6, apply where the piston(s) makes contact with the back of the pad. 4. Chamfer edges (round off sharp leading edges) on brake pads. See picture "Chamfered Pads". 5. After installing the brake linings, actuate the brake for 30 seconds. b) If the noises are coming from the rear axle => Affix linings with adhesive film and grease the lining as per the specification (see attachments for rear axle). 1. Remove brake pads of rear axle. 2. Cleaning all contact points on brake lining and brake caliper/carrier. 3. Grease contact points (red areas) between brake lining and guide of brake caliper with heat-resistant lubricating paste. 4. Clean bonding surface (where pistons contact back of brake pad). Apply adhesive film to the backplate of the piston-side brake lining. 5. Chamfer edges (round off sharp leading edges) on brake pads. See picture "Chamfered Pads". IMPORTANT: Be absolutely certain to not allow paste between friction surfaces of the pad and disc! 3. Brake Bedding Process: a) Before trip, the mileage incurred must be clarified with the customer (approx. 30 miles). b) Select a suitable route so speeds of approximately 65 MPH can be achieved. c) Brake the vehicle 15 times with a brake pressure of approx. 30 bar (have the passenger read it out using XENTRY) from 62 MPH to 30 MPH (no emergency stops and no braking in the ESP control range). Maintain a cooling distance of approx. 1 mile between brake applications. d) Finally drive approx. 3 miles to allow the system to cool. e) Reassess noise. |
| LI00.01-P-078887 | 2025-02-21. Service bulletin. UNKNOWN OR OTHER. Complaint The intent of this document is to provide workshops with helpful technical reference language. • Commonly used acronyms in LI's and TIPS cases. • Control unit names, numbers, and how to identify. • Network/wiring architecture groups to baumuster quick reference. • Platform to baumuster quick reference. Cause Information only Remedy Acronyms: • AV = Actual Values • CU = Control Unit • CUL = Control Unit Log • DTC = Diagnostic Trouble Code • E-Stand = Fresh-up head unit boot software (found in head unit control unit log) • FUP = Fresh-up • FW = Firmware • HSVL = High Speed Video Line • HU = Head Unit • HW = Hardware • ISU = Initial Start Up • LVDS = Low Voltage Differential Signal • NSFT = Not Safe For Transport • MOPF = Model Facelift (Ex: 167 MOPF) • PiH = Plug-in Hybrid • P3 Hybrid = AMG Plug-in Hybrid with rear drive unit • SA Code = Sonderausstattungscode (Option Code) • SCN = Software Calibration Number • SW = Software • TCU = Telecommunication Control Unit (Hermes/Ramses/Etc...) • QT = Quicktest • XD = XENTRY Diagnosis Control Unit Identification: Refer to the attachment "Control Unit Nomenclature" for location of each. • Control Unit Name • Control Unit Number • Control Unit Short name • Control Unit Diogenes ("dy-oj-uh-neez") name - Control unit variant/family. Network/Wiring Architecture to Baumuster Quick Reference: Star 1 • 117, 156, 246 (MFA) • 166, 176, 221, 242, 246, 292 Star 2 • 205, 213, 238, 253, 257, 290 (MRA) • 117, 156, 246 (MFA) • 118, 177, 243, 247 (MFA2) • 167, 222, 292, 463, 465, 906 Star 3 • 294, 295, 296, 297 (EVA2) • 206, 214, 223, 236, 254 (MRA2) • 192 and 232 (MSA) • 907 Platform to Baumuster Quick Reference: MRA = "Mercedes-Benz Rearwheel Architecture": • 205 • 213 • 222 • 238 • 253 • 257 • 290 MRA2 = "Mercedes-Benz Rearwheel Architecture - Generation 2": • 206 • 214 • 223 • 236 • 254 MFA = "Mercedes-Benz Frontwheel Architecture" 117 • 156 • 246 MFA2 = "Mercedes-Benz Frontwheel Architecture - Generation 2" • 118 • 177 • 243 • 247 EVA1.5 = "Electric Vehicle Architecture" • 243 EVA2 = "Electric Vehicle Architecture - Generation 2" • 294 • 295 • 296 • 297 MSA = "Mercedes-Benz Sport Architecture" • 192 • 232 MMA = "Mercedes-Benz Modular Architecture" • No vehicles currently launched. |
| LI72.20-P-073139 | 2025-01-31. Service bulletin. ELECTRICAL SYSTEM; STRUCTURE:BODY. Complaint After CAN bus idle, the tailgate may not fully open (opens to approx. 80 %), regardless of opening method (key, switch, hands-free access, etc.). The tailgate can only be fully opened by operating it again, multiple times where necessary, or by manually raising tailgate. Cause Control unit may falsely detect a blockage. Remedy SCN coding of control unit N121/1 - liftgate control. No replacement of parts are required. |
| LI88.60-P-072093 | 2025-01-29. Service bulletin. STRUCTURE:BODY. Complaint Fuel door may require several attempts to open. Please note that if the complaint "Fuel filler flap not opening" occurs, it is important to check the fuel filler flap before replacing the central locking actuator. For gasoline hybrid vehicles where the fuel filler flap fails to open or does so but slowly, observe the document "Fuel filler flap fails to open or does so but slowly on plug-in HYBRID gasoline vehicles"! Cause Central locking actuator may have an electrical fault and may not open. Remedy 1. Car locked: To rule out incorrect operation, operate the fuel filler flap in the area shown in Fig. 1 and listen out for the clicking noise of the microswitch in the central locking actuator. If no clicking can be heard, continue with point 4. 2. Car unlocked: Press area on flap to start the microswitch clicking. Flap opens - show the customer the area to press. 3. Car unlocked: Flap cannot be opened regardless of which area you press. Open the flap by operating the emergency release for the CL actuator (through trunk, fender gap cover, etc, depending on specific vehicle) 4. Central locking actuator pressed directly, no clicking of microswitch, no electrical release of central locking actuator => Clicking of microswitch, electrical release of central locking actuator => Tank filler recess/charging recess not OK; report results via a TIPS case to B/C/E Inbox. 5. Replace central locking actuator; check function of new part before installing it: Do not dispose of damaged part. New central locking actuator does not release: More detailed examination of connector coupling, wiring harness, electrics required. |
| LI72.00-P-071544 | 2025-01-29. Service bulletin. STRUCTURE:BODY. Complaint Paint damage on door paneling in area of door handle (see picture 1). Cause Alignment of door handle bearing bracket is not correct. Remedy 1. Paint the affected area of the door paneling using the spot repair procedure in accordance with the manufacturer's specifications. 2. Replace the door handle, ensuring that the door handle bearing bracket is installed correctly (see picture 2). Note: The optimized door handles are marked as shown in the illustration (see picture 3). |
| LI63.20-P-069056 | 2025-01-29. Service bulletin. STRUCTURE:BODY. Complaint Noise from windshield (WSS) or A-pillar at left area at speeds between 110 - 140 mph (see "Complaint area" attachment). |
| LI07.61-P-070707 | 2025-01-28. Service bulletin. ENGINE. Complaint The customer complains of a check engine light (CEL) on. May also complain of the engine running roughly and/or a loss of power. Cause Multiple Causes Remedy Please see the document "Remedy Instructions" in attachments. For MY19-24 G63 there may be an alternate solution available, please reference LI07.61-P-076755 before performing the steps in this LI for MY19-24 G63 vehicles. |
| LI42.10-P-063502 | 2025-01-24. Service bulletin. SERVICE BRAKES. Complaint Noises/ squealing from the service brake in various driving situations and ambient conditions. Cause Frictional vibrations Remedy AMG brake systems are designed for high loads. This can result in noises under certain operating conditions and driving styles. Please refer to the Operator's Manual for further information such as care and maintenance instructions (washing vehicle directly after heavy use and using approved cleaning agents). These are dependent on speed, brake pressure or ambient conditions such as temperature and air humidity. 1. Beginning Diagnostics: a) Check whether, apart from this document, an additional document exists for the model series in question, and if so, work through it and then continue with1b. b) Check whether the complaint can be reproduced and at which axle or side the noises occur (ideally together with the customer while driving). c) Check the affected system for component wear, mechanical damage or localized overheating damage. 1. Replace damaged components as necessary and re-assess noise concern. d) Secure vehicle on a lift. 1. Start the engine and depress the brake pedal 3-4 times. 2. Check each wheel to see if they turn freely by hand. 3. If a wheel is not turning freely by hand, this needs to be addressed prior to re-assessing the noise concern. e) Assess condition of brake rotors and pads per WIS and visually (i.e. long periods of stagnation, etc...). 2. Specific Axle Work: NOTE: If brake pad has a metal backing plate, there is no need to affix the adhesive film. a) If the noises are coming from the front axle => Affix linings with adhesive film (see attachments for front axle). If backing plate is installed on pads, move to step 3. 1. Remove brake linings of front axle. 2. Clean all contact points on brake lining and brake caliper/carrier. 3. Clean bonding surface (where pistons contact back of brake pad). Apply adhesive film to the backplate of the piston-side brake lining. For 6 piston calipers, only in the area of the center piston. For other piston caliper configurations less than 6, apply where the piston(s) makes contact with the back of the pad. 4. After installing the brake linings, actuate the brake for 30 seconds. b) If the noises are coming from the rear axle => Affix linings with adhesive film and grease the lining as per the specification (see attachments for rear axle). 1. Remove brake pads of rear axle. 2. Cleaning all contact points on brake lining and brake caliper/carrier. 3. Grease contact points (red areas) between brake lining and guide of brake caliper with heat-resistant lubricating paste. 4. Clean bonding surface (where pistons contact back of brake pad). Apply adhesive film to the backplate of the piston-side brake lining. IMPORTANT: Be absolutely certain to not allow paste between friction surfaces of the pad and disc! 3. Brake Bedding Process: a) Before trip, the mileage incurred must be clarified with the customer (approx. 30 miles). b) Select a suitable route so speeds of approximately 65 MPH can be achieved. c) Brake the vehicle 15 times with a brake pressure of approx. 30 bar (have the passenger read it out using XENTRY) from 62 MPH to 30 MPH (no emergency stops and no braking in the ESP control range). Maintain a cooling distance of approx. 1 mile between brake applications. d) Finally drive approx. 3 miles to allow the system to cool. e) Reassess noise. |
| LI42.10-P-063502 | 2025-01-16. Service bulletin. SERVICE BRAKES. Complaint Noises/ squealing from the service brake in various driving situations and ambient conditions. Cause Frictional vibrations Remedy AMG brake systems are designed for high loads. This can result in noises under certain operating conditions and driving styles. Please refer to the Operator's Manual for further information such as care and maintenance instructions (washing vehicle directly after heavy use and using approved cleaning agents). These are dependent on speed, brake pressure or ambient conditions such as temperature and air humidity. 1. Beginning Diagnostics: a) Check whether, apart from this document, an additional document exists for the model series in question, and if so, work through it. b) Check whether the complaint can be reproduced and at which axle or side the noises occur (ideally together with the customer while driving). c) Check the affected system for component wear, mechanical damage or localized overheating damage. 1. Replace damaged components as necessary and re-assess noise concern. d) Secure vehicle on a lift. 1. Start the engine and depress the brake pedal 3-4 times. 2. Check each wheel to see if they turn freely by hand. 3. If a wheel is not turning freely by hand, this needs to be addressed prior to re-assessing the noise concern. e) Assess condition of brake rotors and pads per WIS and visually (i.e. long periods of stagnation, etc...). 2. Specific Axle Work: a) If the noises are coming from the front axle => Affix linings with adhesive film (see attachments for front axle). 1. Remove brake linings of front axle. 2. Clean all contact points on brake lining and brake caliper/carrier. 3. Clean bonding surface (where pistons contact back of brake pad). Apply adhesive film to the backplate of the piston-side brake lining. For 6 piston calipers, only in the area of the center piston. For other piston caliper configurations less than 6, apply where the piston(s) makes contact with the back of the pad. 4. After installing the brake linings, actuate the brake for 30 seconds. b) If the noises are coming from the rear axle => Affix linings with adhesive film and grease the lining as per the specification (see attachments for rear axle). 1. Remove brake pads of rear axle. 2. Cleaning all contact points on brake lining and brake caliper/carrier. 3. Grease contact points (red areas) between brake lining and guide of brake caliper with heat-resistant lubricating paste. 4. Clean bonding surface (where pistons contact back of brake pad). Apply adhesive film to the backplate of the piston-side brake lining. 5. IMPORTANT: Be absolutely certain to not allow paste between friction surfaces of the pad and disc! 3. Brake Bedding Process: a) Before trip, the mileage incurred must be clarified with the customer (approx. 30 miles). b) Select a suitable route so speeds of approximately 65 MPH can be achieved. c) Brake the vehicle 15 times with a brake pressure of approx. 30 bar (have the passenger read it out using XENTRY) from 62 MPH to 30 MPH (no emergency stops and no braking in the ESP control range). Maintain a cooling distance of approx. 1 mile between brake applications. d) Finally drive approx. 3 miles to allow the system to cool. e) Reassess noise. |
| LI46.80-P-078043 | 2025-01-10. Service bulletin. ELECTRICAL SYSTEM. Complaint Message in the instrument cluster regarding rear axle steering • In the short test, the fault > Actuator blocked < appears Cause Vehicle may detect high adjustment force in the rear axle steering. Remedy NOTE: If hardware and software numbers do not match exactly what is listed below, please follow DTC guided tests. Old Hardware: A 290 460 3300 / 3400 > SW A 290 902 7400 Caution! This hardware cannot be flashed with the new software version. Only the current hardware with the corresponding previous software release can be flashed. Current Hardware: A 290 460 3900 / 4000 >> SW A 290 902 5101 This hardware can be flashed with A 290 902 1005. Flash control unit N68/3 and N68/4 with current software release A 290 902 1005 using XD. |
| LI09.41-P-078735 | 2024-12-23. Service bulletin. ENGINE. Complaint Check engine light illuminated Fault code present in MRG3 control unit P22C900 - The valve of the exhaust gas turbocharger is jammed closed. Cause Check valve in charge air pipe jammed closed. Remedy Replaced charge air line with check valve. |
| LI03.20-P-078715 | 2024-12-23. Service bulletin. ENGINE. Complaint Low engine oil level warning. Engine oil leak under vehicle. Cause Rear crankshaft radial seal rolled during installation Remedy -Check for external oil leak with visual inspection. -Remove inspection cover on left side of transmission and check for oil in bell housing. -If oil is found in bell housing, remove transmission and determine location of leak. Replace rear crankshaft sealing ring if found damaged or leaking. -If ISA is found to be contaminated with engine oil, replace the integrated starter/alternator. |
The summaries are NHTSA's. Each bulletin's page links NHTSA's copy of the manufacturer's document.