Service bulletins for the 2026 Mazda Mazda3
A bulletin is a manufacturer's communication to its dealers, as NHTSA indexes it. The summary is NHTSA's. The document is the manufacturer's: read it at NHTSA. A bulletin is not a recall, and listing a model year does not mean every vehicle of it is concerned.
76 on file from NHTSA, as of 2026-10-19.
By type
By component
By trouble code
By topic
Only bulletins with component: Body and frame are shown. Show all
| 09-026-26 | 2026-10-01. Service bulletin. STRUCTURE:BODY. This bulletin supersedes the previously issued bulletin(s) listed below. The changes are noted in Red text. 09-043/25 11/26/2025 DESCRIPTION Some vehicles may experience a clicking noise when opening and/or closing the front door due to a broken front door checker plate. To reduce the clicking noise, the material of the plastic component in the door checker has been modified. REPAIR PROCEDURE 1. Verify the customer concern. 2. Replace the front door checker plate with the interim countermeasure part according to the instructions on MGSS FRONT DOOR CHECKER REMOVAL/INSTALLATION. NOTE: Repair only the affected side. |
|---|---|
| SA-031-26 | 2026-05-05. Service bulletin. STRUCTURE:BODY; UNKNOWN OR OTHER. DESCRIPTION Some vehicles may require the replacement of a damaged VIN plate or vehicle certification label. To obtain a replacement VIN plate (bulkhead-mounted and visible through the lower-left area of the windshield), contact DAG (Dealer Assistance Group) using VIN Plate Request Form available on One Mazda. To obtain a replacement vehicle certification label (located on the Bpillar or front door), contact your assigned DSM (District Service Manager) to place the order. If DSM contact information is not available, refer to the Dealer & Field Contact Directory. |
| SA-019-26 | 2026-04-03. Service bulletin. STRUCTURE:BODY; UNKNOWN OR OTHER. This SA supersedes the previously issued SA(s) listed below. The changes are noted in Red. SA-045/22 12/06/22 and 07/12/22 NOTE: All vehicles with protective films applied to the piano black door garnishes of the following models are applicable to this Service Alert. DESCRIPTION The purpose of this Service Alert is to remind dealers to keep the protective films on the piano black door garnishes attached until just before delivering the vehicle to the customer. The protective films are attached on new vehicles when shipped from the factory in order to avoid being scratched during transportation and while in dealer stock. NOTE: Remove the protective films after cleaning the vehicle. • If any adhesive residue remains on the surface of the door garnish, attach the adhesive side of the protective film on the area again, and then peel it off to remove the residue. • Refer to the image below for the location of the protective films (4 sheets of films in each side). |
| 09-043-25 | 2025-12-04. Service bulletin. STRUCTURE:BODY. Some vehicles may experience a clicking noise when opening and/or closing the front door due to a broken front door checker plate. |
| 09-042-25 | 2025-12-04. Service bulletin. UNKNOWN OR OTHER; STRUCTURE:BODY. Some customers may experience that after the doors are locked and the Fuel Door Lock Delay with MAZDA CONNECT has passed (default setting is 90 seconds), the fuel-filler lid does not lock, but can be opened when pressed. NOTE: The fuel-filler lid does not lock immediately after the doors are locked, but after the time set in the Fuel Door Lock Delay (0, 30, 60, 90, and 120 seconds). Although the root cause has not been identified, the vehicle should be repaired by adjusting the fuel-filler lid opener cable position when there is a customer complaint. |
| SA-011-25a | 2025-11-05. Service bulletin. STRUCTURE:BODY. Some customers will report that their fuel door (AKA, fuel filler door, fuel lid, and fuel-filler lid) was stuck closed and would not open to refuel the vehicle. Follow the repair steps below unless the conditions outlined in TSB 09-007/25 - FUEL-FILLER LID PANEL IS DEFORMED for 2019-2025 Mazda3 and 2020-2025 CX-30 are present. |
| 09-034-25a | 2025-11-05. Service bulletin. STRUCTURE:BODY. Some customers may notice water in the trunk after a car wash or heavy rain. This may be caused by insufficient sealing performance of the trunk lid weatherstrip. Due to improper installation of weatherstrips, the lip of the weatherstrip may lean toward the inside of the trunk, resulting in insufficient sealing performance. To eliminate this concern, the length of the trunk lid weatherstrip has been extended 14 mm {0.5 in.}. |
| SA-039/25 | 2025-09-05. Service bulletin. UNKNOWN OR OTHER; STRUCTURE:BODY. Some vehicles may experience exterior trim heat damage such (melted, separating, etc.) when parked near a glass building or Low-E windows. This may be caused by the sun's reflection. If a structure's windows create enough of a curve, the concave glass can focus the sun's rays onto a small area and acting like magnifiying glass direct the sunbeams into a hot pinpoint of light. This magnifcation of the sun's rays can cause damage to vehicle trim (see examples). Additional information and exemplar images regarding this phenomenon can be found by performing a google search. |
| 09-034-25 | 2025-09-04. Service bulletin. UNKNOWN OR OTHER; STRUCTURE:BODY. Some customers may notice water in the trunk after a car wash or heavy rain. This may be caused by insufficient sealing performance of the trunk lid weatherstrip. Due to improper installation of weatherstrips, the lip of the weatherstrip may lean toward the inside of the trunk, resulting in insufficient sealing performance. |
The summaries are NHTSA's. Each bulletin's page links NHTSA's copy of the manufacturer's document.