WenmarOpen by Wenmar Pro

Service bulletins for the 2013 Mazda Mazda3

A bulletin is a manufacturer's communication to its dealers, as NHTSA indexes it. The summary is NHTSA's. The document is the manufacturer's: read it at NHTSA. A bulletin is not a recall, and listing a model year does not mean every vehicle of it is concerned.

504 on file from NHTSA, as of 2026-10-19.

By type

By component

By trouble code

By topic

Bulletins, newest first
08-001-13-28592017-08-10. Service bulletin. AIR BAGS; ELECTRICAL SYSTEM. This information is provided to help address Passenger Airbag Deactivation (PAD) Indicator illumination con-cerns during vehicle service.
09-035-13-28572017-08-10. Service bulletin. EQUIPMENT:ELECTRICAL; EQUIPMENT:ELECTRICAL:NAVIGATIONAL SYSTEM(GLOBAL POSITIONING SYSTEM). On some vehicles, the customer may complain about any one of the following concerns: *Screen locks up to a "black screen". *Screen freezes while driving. *Screen gets stuck at TomTom logo (splash screen) during startup. *Screen temporarily gets stuck at TomTom logo (splash screen) for 2 minutes during startup. Afterwards, the navigation will not start until the ignition is cycled. *No Map Found error and SD card contains a map. *Yellow screen with message "Insert SD card". *Red screen with message "Problem with map". *The message "Waiting for a valid GPS signal" appears. *Current car position (CCP) turning 180 degrees when driving in reverse. *Unexpected "Stopping voice control" message, usually when starting the vehicle. *Navigation screen does not appear after pressing the NAVI button and it will not recover after turning the ignition OFF, then ON again.
04-004-16-31602017-06-09. Service bulletin. SERVICE BRAKES. SOME VEHICLES EXHIBIT BRAKE RELATED CONCERNS SUCH AS BRAKE NOISE, BRAKE JUDDER OR BRAKE DRAGGING. IF YOU ENCOUNTER A CUSTOMER COMPLAINT FOR ANY ONE OF THESE SYMPTOMS, REFER TO THE FOLLOWING INFORMATION TO UNDERSTAND WHY SYMPTOMS MAY OCCUR, AND TO BETTER ASSIST THE CUSTOMER IN RESOLVING THEIR SPECIFIC BRAKE CONCERN.
09-013-16-31612017-06-09. Service bulletin. EQUIPMENT. WHEN DEALING WITH CUSTOMER COMPLAINTS OF EXCESSIVE CONDENSATION AND/OR WATER WITHIN THE HEADLAMP UNIT, FIRST DETERMINE IF ALL THE BULB SOCKETS ARE RESENT AND CORRECTLY INSTALLED. IN MOST CASES YOU WILL FIND THAT THE BULB SEAL NO. 1 (A) OR HID BULB SEAL NO. 1 (B) AND BULB SEAL NO. 2 (C) SOCKET OVERS HAVE NOT BEEN CORRECTLY INSTALLED OR ARE MISSING DUE TO IMPROPER PRIOR REPAIRS (I.E., CUSTOMER REPLACING THE HEADLAMP BULBS OR BODY SHOP NOT TRANSFERRING THEM WHEN REPLACING THE HEADLAMP UNIT(S) DUE TO A COLLISION). ANY DAMAGE CAUSED BY MISSING SOCKET COVERS, HID MODULE SEAL (D), OR MISSING BUMPER BRACKETS (E) IS NOT COVERED BY WARRANTY POLICY.
02-002-16-31242017-06-09. Service bulletin. WHEELS. SOME AUTOMOTIVE CLEANING PRODUCTS CONTAIN STRONG ACID OR ALKALI. WHEN THESE TYPES OF CLEANERS ARE USED TO CLEAN THE WHEELS ON MAZDA VEHICLES, THE CHEMICALS CONTENTS PENETRATE THE CLEAR COATING OF THE WHEEL SURFACE AND DAMAGE THE PAINT UNDER THE CLEAR COATING. THE DAMAGED AREA HAS THE APPEARANCE OF DARK STAINS.
00-001-16-31272017-06-09. Service bulletin. EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL. IN SUPPORT OF IMPROVED ELECTRICAL DIAGNOSIS ON SKYACTIV VEHICLES, MAZDA WILL SHIP A TERMINAL TEST KIT TO ALL DEALERS. THE TEST KIT IS DESIGNED PECIFICALLY FOR SKYACTIV MODULE TERMINALS.• THE SST WILL BE SHIPPED BY MAZDA’S TOOL VENDOR BOSCH STARTING JANUARY 15, 2016.• PROCEDURES FOR USAGE ARE FOUND IN THE SKYACTIV WIRING TERMINAL TEST KIT WBT, COURSE #1649.• THE FOLLOWING SST IS THE LATEST ADDITION TO THE MAZDA REQUIRED TOOL (MRT) LIST:
05-002-15-3019F2017-06-08. Service bulletin. ENGINE; POWER TRAIN:AUTOMATIC TRANSMISSION. SOME VEHICLES MAY EXPERIENCE THE CHECK ENGINE LIGHT AND AUTOMATIC TRANSAXLE WARNING LIGHT ON WITH ONE OR MORE OF THESE DTCS STORED IN THE TCM MEMORY (P0842, P0847, P0872, P0877, P0780, P1738). • P0842:00 - OIL PRESSURE SWITCH NO. 1 (OIL PRESSURE SWITCH B) STUCK ON • P0847:00 - OIL PRESSURE SWITCH NO. 2 (OIL PRESSURE SWITCH A) STUCK ON • P0872:00 - OIL PRESSURE SWITCH NO. 3 (OIL PRESSURE SWITCH A) STUCK ON • P0877:00 - OIL PRESSURE SWITCH NO. 4 (OIL PRESSURE SWITCH B) STUCK ON • P0780:00 - GEAR SHIFTING MALFUNCTION • P1738:00 AUTOMATIC TRANSAXLE INTERNAL MALFUNCTION THIS IS CAUSED BY THE OIL PRESSURE SWITCH A AND/OR B AT THE CONTROL VALVE BODY TEMPORARILY OR PERMANENTLY GETTING STUCK DUE TO CONTAMINATION ENTERING THE PASSAGE. TO CORRECT THE PROBLEM, SOME MASS PRODUCTION CHANGES HAVE BEEN IMPLEMENTED TO REDUCE CONTAMINATION AND IMPROVE THE DTC DIAGNOSTIC LOGIC. NOTE: IF THE VEHICLE ALSO HAS A DELAYED ENGAGEMENT CONCERN, THIS TSB IS NOT APPLICABLE. REFER TO MS3 ONLINE INSTRUCTIONS OR WORKSHOP MANUAL FOR PROPER DIAGNOSIS AND REPAIR PROCEDURE.
01-014-15-3055A2017-06-08. Service bulletin. ENGINE. FREQUENT ENGINE STARTS UNDER EXTREMELY COLD AMBIENT TEMPERATURES MAY RESULT IN OIL SEEPAGE FROM THE ENGINE OIL PRESSURE SWITCH. THIS CONCERN MAY BE CAUSED BY A LACK OF DURABILITY OF THE OIL PRESSURE SWITCH UNDER THESE CONDITIONS. TO CORRECT THE PROBLEM, THE OIL PRESSURE SWITCH HAS BEEN IMPROVED TO INCREASE THE DURABILITY IN COLD AMBIENT TEMPERATURES.
01-023-15-3084B2017-06-08. Service bulletin. ENGINE. SOME VEHICLES MAY EXPERIENCE A ROUGH IDLE WITH THE MIL ON AND DTC P0015 / P0524 STORED IN MEMORY. • P0015:00 - EXHAUST CMP TIMING OVER-RETARDED • P0524:00 - ENGINE OIL PRESSURE TOO LOW THIS IS CAUSED BY A DROP IN ENGINE OIL PRESSURE DUE TO A PIECE OF FOREIGN OBJECT STUCK ON THE OIL PUMP PRESSURE RELIEF VALVE OR OCV. THE TEMPORARY ENTRY OF THE FOREIGN OBJECT TRIGGERS A MIL ILLUMINATION, BUT ROUGH IDLE WILL NOT BE PRODUCED UNTIL A LATER TIME.
01-023-15-3084A2017-06-08. Service bulletin. ENGINE. SOME VEHICLES MAY EXPERIENCE A ROUGH IDLE WITH THE MIL ON AND DTC P0015 / P0524 STORED IN MEMORY. • P0015:00 - EXHAUST CMP TIMING OVER-RETARDED • P0524:00 - ENGINE OIL PRESSURE TOO LOW THIS IS CAUSED BY A DROP IN ENGINE OIL PRESSURE DUE TO A PIECE OF FOREIGN OBJECT STUCK ON THE OIL PUMP PRESSURE RELIEF VALVE OR OCV. THE TEMPORARY ENTRY OF THE FOREIGN OBJECT TRIGGERS A MIL ILLUMINATION, BUT ROUGH IDLE WILL NOT BE PRODUCED UNTIL A LATER TIME.
05-001-15-31042017-06-08. Service bulletin. POWER TRAIN:AUTOMATIC TRANSMISSION:GEAR POSITION INDICATION (PRNDL). SOME VEHICLES MAY EXHIBIT ONE OF THE FOLLOWING CONCERNS: • SOMETIMES THE SHIFTER MAY JUMP OUT OF 3RD GEAR OVER A ROAD BUMP WHEN ACCELERATING AFTER DECELERATION AT 25-40 MPH (40-65 KM/H) • HARD TO SHIFT INTO 3RD, 4TH, 5TH, AND/OR 6TH GEAR • SHIFT LEVER VIBRATES WHEN DRIVING IN 3RD OR 4TH GEAR THIS IS CAUSED BY INAPPROPRIATE TRANSMISSION INTERNAL PARTS.
05-005-15-3027A2017-06-08. Service bulletin. POWER TRAIN:AUTOMATIC TRANSMISSION; POWER TRAIN:AXLE ASSEMBLY. SOME CUSTOMERS MAY COMPLAIN OF A WHINING NOISE FROM THE AUTOMATIC TRANSAXLE WHEN DRIVING AT 10 MPH AND ABOVE. THE NOISE: • DEPENDS ON THE VEHICLE’S SPEED ONLY (THE MORE SPEED, THE MORE NOISE) • OCCURS WITH ALL TYPES OF DRIVING (ACCELERATION, DECELERATION, STEADY SPEED) • DOES NOT DEPEND ON RPM, GEAR, OR ATF TEMPERATURE. THIS IS CAUSED BY A DAMAGED BEARING IN THE TRANSAXLE DUE TO IMPROPER CONFIGURATION OF THE TRANSAXLE CASE. A MODIFICATION HAS NOW BEEN IMPLEMENTED ON AUTOMATIC TRANSAXLES WITH THE SERIAL NUMBER 3TR1111680 AND HIGHER OR 3TD1104906 AND HIGHER. THE SERIAL NUMBER CAN BE FOUND ON TOP OF THE TRANSAXLE CASE NEAR THE MANUAL SHAFT LEVER.
05-001-15-3104A2017-06-08. Service bulletin. POWER TRAIN:AUTOMATIC TRANSMISSION:GEAR POSITION INDICATION (PRNDL). SOME VEHICLES MAY EXHIBIT ONE OF THE FOLLOWING CONCERNS: • SOMETIMES THE SHIFTER MAY JUMP OUT OF 3RD GEAR OVER A ROAD BUMP WHEN ACCELERATING AFTER DECELERATION AT 25-40 MPH (40-65 KM/H) • HARD TO SHIFT INTO 3RD, 4TH, 5TH, AND/OR 6TH GEAR • SHIFT LEVER VIBRATES WHEN DRIVING IN 3RD OR 4TH GEAR THIS IS CAUSED BY INAPPROPRIATE TRANSMISSION INTERNAL PARTS.
05-006-15-31072017-06-07. Service bulletin. EQUIPMENT; VEHICLE SPEED CONTROL. SOME VEHICLES MAY EXHIBIT THE ATX FAIL-SAFE FUNCTION WORKING WITH THE FOLLOWING SYMPTOMS: • THE VEHICLE SPEED DOES NOT INCREASE WITH ENGINE SPEED • THE ATX DOES NOT SHIFT UP OR DOWN AS EXPECTED THE CONDITION MAY NOT ALWAYS BE ABLE TO BE REPRODUCED AND DTCS MAY NOT BE STORED WHEN THE VEHICLE IS BROUGHT IN. FOREIGN MATERIAL (IRON PARTICLES IN THE ATF) MAY ENTER THE ATX VALVE BODY AND CAUSE A TEMPORARY MALFUNCTION OF THE VALVE BODY AND/OR SENSOR (ATX FAIL-SAFE FUNCTION ACTIVATED). THE FAIL-SAFE FUNCTION IS CANCELED WITHOUT DTCS RECORDED IF THE MALFUNCTION GOES AWAY AND DOES NOT OCCUR AGAIN AT THE NEXT DRIVE CYCLE.
05-002-15-3019E2017-06-07. Service bulletin. ELECTRICAL SYSTEM; EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL. SOME VEHICLES MAY EXPERIENCE THE CHECK ENGINE LIGHT AND AUTOMATIC TRANSAXLE WARNING LIGHT ON WITH ONE OR MORE OF THESE DTCS STORED IN THE TCM MEMORY (P0842, P0847, P0872, P0877, P0780). • P0842:00 - OIL PRESSURE SWITCH NO. 1 (OIL PRESSURE SWITCH B) STUCK ON • P0847:00 - OIL PRESSURE SWITCH NO. 2 (OIL PRESSURE SWITCH A) STUCK ON • P0872:00 - OIL PRESSURE SWITCH NO. 3 (OIL PRESSURE SWITCH A) STUCK ON • P0877:00 - OIL PRESSURE SWITCH NO. 4 (OIL PRESSURE SWITCH B) STUCK ON • P0780:00 - GEAR SHIFTING MALFUNCTION THIS IS CAUSED BY THE OIL PRESSURE SWITCH A AND/OR B AT THE CONTROL VALVE BODY TEMPORARILY OR PERMANENTLY GETTING STUCK DUE TO CONTAMINATION ENTERING THE PASSAGE. TO CORRECT THE PROBLEM, SOME MASS PRODUCTION CHANGES HAVE BEEN IMPLEMENTED TO REDUCE CONTAMINATION AND IMPROVE THE DTC DIAGNOSTIC LOGIC. NOTE: IF THE VEHICLE ALSO HAS A DELAYED ENGAGEMENT CONCERN, THIS TSB IS NOT APPLICABLE. REFER TO MS3 ONLINE INSTRUCTIONS OR WORKSHOP MANUAL FOR PROPER DIAGNOSIS AND REPAIR PROCEDURE.
09-030-15-30732017-06-07. Service bulletin. EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL. MAZDA INFOTAINMENT SYSTEMS REQUIRE CONTACTING THE PROPER SOURCE FOR DIAGNOSTIC SUPPORT, PARTS AUTHORIZATION, AND PARTS EXCHANGE. SOME COMPONENTS REQUIRE PRIOR AUTHORIZATION BEFORE ORDERING AS EXCHANGE. REFER TO DAG EXCHANGE CENTRAL (MXCONNECT>PARTS AND ACCESSORIES>PARTS>PROGRAMS>EXCHANGE CENTRAL) FOR COMPONENT AVAILABILITY, SOURCE OF TECHNICAL SUPPORT AND PRIOR AUTHORIZATION REQUIREMENT. NOTE: ALWAYS CHECK FOR A TSB THAT MAY MODIFY OR ELIMINATE PRIOR AUTHORIZATION FOR A SPECIFIC SYMPTOM FOR A GIVEN COMPONENT.
09-031-15-30762017-06-07. Service bulletin. EQUIPMENT:ELECTRICAL:NAVIGATIONAL SYSTEM(GLOBAL POSITIONING SYSTEM). THE NAVIGATION SYSTEM SUPPORT FOR DIAGNOSTICS, PARTS AUTHORIZATION, AND PARTS EXCHANGE REQUIRE CONTACTING THE PROPER SOURCE. • TOMTOM NAVIGATION HELP DESK AT 866-486-6866 FROM 7AM-11PM (M-F) AND 9AM-8PM (SAT) EASTERN STANDARD TIME. NOTE: ONE OF THE FIRST STEPS FOR TROUBLESHOOTING THE NAVIGATION SYSTEM IS FOR THE CUSTOMER OR DEALER TO CALL TOMTOM. IF THE TOMTOM CALL CENTER CANNOT SOLVE THE CUSTOMER’S PROBLEM, THEY WILL PROVIDE A CASE NUMBER TO THE CUSTOMER THAT CAN BE REFERRED TO IF NEEDED. SERVICE ADVISORS SHOULD GET THIS CASE NUMBER FROM THE CUSTOMER IF THE VEHICLE COMES INTO THE DEALER FOR FURTHER DIAGNOSIS SO THE TECHNICIAN CAN HAVE IT WHEN CALLING TOMTOM.
01-020-15-29302017-06-07. Service bulletin. ENGINE; EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL. SOME VEHICLES MAY EXPERIENCE THE CHECK ENGINE LIGHT ON WITH DTC P0300:00, P0301:00, P0302:00, P0303:00 AND/OR P0304:00 STORED IN MEMORY. • P0300:00: RANDOM MISFIRE DETECTED • P0301:00: CYLINDER NO.1 MISFIRE DETECTED • P0302:00: CYLINDER NO.2 MISFIRE DETECTED • P0303:00: CYLINDER NO.3 MISFIRE DETECTED • P0304:00: CYLINDER NO.4 MISFIRE DETECTED CARBON MAY BE DEPOSITED AROUND THE INTAKE VALVES, RESULTING IN UNSTABLE ENGINE COMBUSTION AND MISFIRING DURING THE ACCELERATED WARM-UP SYSTEM (AWS) OPERATION.
09-008-15-2991C2017-06-07. Service bulletin. EQUIPMENT:ELECTRICAL:RADIO/TAPE DECK/CD ETC.. SOME CUSTOMERS MAY COMPLAIN ABOUT ONE OR MORE OF THE FOLLOWING CONCERNS. 1. SMS/TEXT CANNOT BE DOWNLOADED WHEN ONNECTED VIA BLUETOOTH. 2. OPERATIONAL CONCERNS WHEN PLAYING A MEDIA DEVICE (IPOD, USB STICK ETC.) CONNECTED VIA THE USB PORT. A. AFTER THE IGNITION IS TURNED ON, IT TAKES A LONG TIME TO LOAD ALL THE DATA FROM THE DEVICE BEFORE STARTING PLAYBACK. DEPENDING ON THE DATA VOLUME, IT CAN TAKE UP TO SEVERAL MINUTES. B. AFTER THE IGNITION IS TURNED ON, THE PLAYBACK ALWAYS STARTS FROM THE FIRST TRACK. IT DOES NOT START FROM THE LAST PLAYING TRACK/POSITION WHEN THE IGNITION WAS TURNED OFF. C. “IPOD ERROR” MESSAGE FOR THE APPLE® IOS 8.0 OR HIGHER SOFTWARE ON IPHONE 4, 5, OR 6. THESE CONCERNS MAY BE CAUSED BY THE SOFTWARE OF THE BLUETOOTH/HANDS-FREE MODULE THAT CONTROLS THE USB CONNECTION. TO IMPROVE THESE CONCERNS, THE SOFTWARE OF THE BLUETOOTH/HANDS-FREE MODULE HAS BEEN CHANGED. NOTE: • THE UPDATED SOFTWARE OF THE BLUETOOTH/HANDS-FREE MODULE WILL ONLY ADDRESS SMS/TEXT CONCERNS FOR THE APPLE® IPHONE AT THIS TIME.
01-008-15-30452017-06-07. Service bulletin. EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL. SOME VEHICLES MAY EXHIBIT THE CHECK ENGINE LIGHT ON WITH DTC P0456 STORED IN THE PCM MEMORY. • P0456: EVAP SYSTEM LEAK DETECTED (VERY SMALL LEAK) THE CONCERN IS MOST LIKELY THE RESULT OF THE CUSTOMER NOT GETTING THE FUEL CAP COMPLETELY CLOSED AFTER FUELING THE VEHICLE. THIS CAUSES A SMALL FUEL VAPOR LEAK AND TURNS DTC P0456 ON.
05-002-15-3019D2017-06-07. Service bulletin. EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL. SOME VEHICLES MAY EXPERIENCE THE CHECK ENGINE LIGHT AND AUTOMATIC TRANSAXLE WARNING LIGHT ON WITH ONE OR MORE OF THESE DTCS STORED IN THE TCM MEMORY (P0842, P0847, P0872, P0877, P0780). • P0842:00 - OIL PRESSURE SWITCH NO. 1 (OIL PRESSURE SWITCH B) STUCK ON • P0847:00 - OIL PRESSURE SWITCH NO. 2 (OIL PRESSURE SWITCH A) STUCK ON • P0872:00 - OIL PRESSURE SWITCH NO. 3 (OIL PRESSURE SWITCH A) STUCK ON • P0877:00 - OIL PRESSURE SWITCH NO. 4 (OIL PRESSURE SWITCH B) STUCK ON • P0780:00 - GEAR SHIFTING MALFUNCTION THIS IS CAUSED BY THE OIL PRESSURE SWITCH A AND/OR B AT THE CONTROL VALVE BODY TEMPORARILY OR PERMANENTLY GETTING STUCK DUE TO CONTAMINATION ENTERING THE PASSAGE. TO CORRECT THE PROBLEM, SOME MASS PRODUCTION CHANGES HAVE BEEN IMPLEMENTED TO REDUCE CONTAMINATION AND IMPROVE THE DTC DIAGNOSTIC LOGIC.
05-004-15-3034C2017-06-07. Service bulletin. EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL. SOME CUSTOMERS MAY COMPLAIN OF A CHECK ENGINE LIGHT AND A/T WARNING LIGHT ON WHEN STARTING THE ENGINE. AT THE SAME TIME, AN ENGINE INSPECTION REQUIRED MESSAGE IS DISPLAYED ON THE LCD. DTC P0722:00 IS STORED IN THE TRANSMISSION CONTROL MODULE (TCM) MEMORY. • DTC P0722:00 (OPEN CIRCUIT IN OUTPUT SPEED SHAFT CIRCUIT) THE TCM CONTROL LOGIC HAS BEEN CHANGED TO ELIMINATE THIS CONCERN.
01-015-15-3064A2017-05-31. Service bulletin. EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL. SOME VEHICLES USING AN AUXILIARY HEATER (BLOCK HEATER) MAY EXPERIENCE THE CHECK ENGINE LIGHT ON WITH DTC P0116:00 OR P011A WHEN STARTING IN COLD WEATHER BELOW 32 °F (0 °C). • P0116:00: ECT SENSOR NO.1 CIRCUIT RANGE/PERFORMANCE PROBLEM • P011A:00: ECT SENSOR NO.1/NO.2 PERFORMANCE PROBLEM THIS IS CAUSED BY ERROR DETECTION LOGIC OF THE PCM. TO CORRECT THE PROBLEM, THE CONTROL LOGIC OF THE PCM HAS BEEN CHANGED.
01-023-15-30842017-05-31. Service bulletin. EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL; ENGINE. SOME VEHICLES MAY EXPERIENCE A ROUGH IDLE WITH THE MIL ON AND DTC P0015 / P0524 STORED IN MEMORY. • P0015:00 - EXHAUST CMP TIMING OVER-RETARDED • P0524:00 - ENGINE OIL PRESSURE TOO LOW THIS IS CAUSED BY A DROP IN ENGINE OIL PRESSURE DUE TO A PIECE OF FOREIGN OBJECT STUCK ON THE OIL PUMP PRESSURE RELIEF VALVE OR OCV. THE TEMPORARY ENTRY OF THE FOREIGN OBJECT TRIGGERS A MIL ILLUMINATION, BUT ROUGH IDLE WILL NOT BE PRODUCED UNTIL A LATER TIME.
01-009-16-31722017-05-30. Service bulletin. EQUIPMENT ADAPTIVE/MOBILITY; ENGINE AND ENGINE COOLING; ENGINE. SOME VEHICLES MAY EXPERIENCE A ROUGH IDLE WITH THE CHECK ENGINE LIGHT ON AND DTC P0015 / P0524 STORED IN MEMORY.•P0015:00 - EXHAUST CMP TIMING OVER-RETARDED•P0524:00 - ENGINE OIL PRESSURE TOO LOWTHIS IS CAUSED BY A DROP IN ENGINE OIL PRESSURE DUE TO A PIECE OF FOREIGN OBJECT STUCK ON THE OIL PUMP PRESSURE RELIEF VALVE OR OIL CONTROL VALVE (OCV). THE TEMPORARY ENTRY OF THE FOREIGN OBJECT TRIGGERS A CHECK ENGINE LIGHT ON, BUT ROUGH IDLE WILL NOT BE PRODUCED UNTIL A LATER TIME.

The summaries are NHTSA's. Each bulletin's page links NHTSA's copy of the manufacturer's document.