Service bulletins for the 2013 Mazda Mazda3
A bulletin is a manufacturer's communication to its dealers, as NHTSA indexes it. The summary is NHTSA's. The document is the manufacturer's: read it at NHTSA. A bulletin is not a recall, and listing a model year does not mean every vehicle of it is concerned.
504 on file from NHTSA, as of 2026-10-19.
By type
By component
By trouble code
By topic
Only bulletins with component: Engine are shown. Show all
| SA-060-17 | 2017-08-10. Service bulletin. POWER TRAIN:AUTOMATIC TRANSMISSION:CONTROL MODULE (TCM/PCM/TECM); ELECTRICAL SYSTEM:SOFTWARE; ENGINE. Some 2012-2016 Mazda3s, 2013-2015 CX-5s and 2014-2015 Mazda6s may experience the Check Engine Light ON with DTC P0101 and/or P061B and/or driveability problem after reprogramming the PCM using IDS versions 105.02 to 105.04. If the PCM is reprogrammed with any software number included in the attached file and the throttle valve has too much carbon build up, the engine air amount calculation by the problem software may not be accurate. Perform the following Repair Procedure to correct this issue. NOTE Current version of IDS is 106.02. |
|---|---|
| 05-002-15-3019F | 2017-06-08. Service bulletin. ENGINE; POWER TRAIN:AUTOMATIC TRANSMISSION. SOME VEHICLES MAY EXPERIENCE THE CHECK ENGINE LIGHT AND AUTOMATIC TRANSAXLE WARNING LIGHT ON WITH ONE OR MORE OF THESE DTCS STORED IN THE TCM MEMORY (P0842, P0847, P0872, P0877, P0780, P1738). • P0842:00 - OIL PRESSURE SWITCH NO. 1 (OIL PRESSURE SWITCH B) STUCK ON • P0847:00 - OIL PRESSURE SWITCH NO. 2 (OIL PRESSURE SWITCH A) STUCK ON • P0872:00 - OIL PRESSURE SWITCH NO. 3 (OIL PRESSURE SWITCH A) STUCK ON • P0877:00 - OIL PRESSURE SWITCH NO. 4 (OIL PRESSURE SWITCH B) STUCK ON • P0780:00 - GEAR SHIFTING MALFUNCTION • P1738:00 AUTOMATIC TRANSAXLE INTERNAL MALFUNCTION THIS IS CAUSED BY THE OIL PRESSURE SWITCH A AND/OR B AT THE CONTROL VALVE BODY TEMPORARILY OR PERMANENTLY GETTING STUCK DUE TO CONTAMINATION ENTERING THE PASSAGE. TO CORRECT THE PROBLEM, SOME MASS PRODUCTION CHANGES HAVE BEEN IMPLEMENTED TO REDUCE CONTAMINATION AND IMPROVE THE DTC DIAGNOSTIC LOGIC. NOTE: IF THE VEHICLE ALSO HAS A DELAYED ENGAGEMENT CONCERN, THIS TSB IS NOT APPLICABLE. REFER TO MS3 ONLINE INSTRUCTIONS OR WORKSHOP MANUAL FOR PROPER DIAGNOSIS AND REPAIR PROCEDURE. |
| 01-014-15-3055A | 2017-06-08. Service bulletin. ENGINE. FREQUENT ENGINE STARTS UNDER EXTREMELY COLD AMBIENT TEMPERATURES MAY RESULT IN OIL SEEPAGE FROM THE ENGINE OIL PRESSURE SWITCH. THIS CONCERN MAY BE CAUSED BY A LACK OF DURABILITY OF THE OIL PRESSURE SWITCH UNDER THESE CONDITIONS. TO CORRECT THE PROBLEM, THE OIL PRESSURE SWITCH HAS BEEN IMPROVED TO INCREASE THE DURABILITY IN COLD AMBIENT TEMPERATURES. |
| 01-023-15-3084B | 2017-06-08. Service bulletin. ENGINE. SOME VEHICLES MAY EXPERIENCE A ROUGH IDLE WITH THE MIL ON AND DTC P0015 / P0524 STORED IN MEMORY. • P0015:00 - EXHAUST CMP TIMING OVER-RETARDED • P0524:00 - ENGINE OIL PRESSURE TOO LOW THIS IS CAUSED BY A DROP IN ENGINE OIL PRESSURE DUE TO A PIECE OF FOREIGN OBJECT STUCK ON THE OIL PUMP PRESSURE RELIEF VALVE OR OCV. THE TEMPORARY ENTRY OF THE FOREIGN OBJECT TRIGGERS A MIL ILLUMINATION, BUT ROUGH IDLE WILL NOT BE PRODUCED UNTIL A LATER TIME. |
| 01-023-15-3084A | 2017-06-08. Service bulletin. ENGINE. SOME VEHICLES MAY EXPERIENCE A ROUGH IDLE WITH THE MIL ON AND DTC P0015 / P0524 STORED IN MEMORY. • P0015:00 - EXHAUST CMP TIMING OVER-RETARDED • P0524:00 - ENGINE OIL PRESSURE TOO LOW THIS IS CAUSED BY A DROP IN ENGINE OIL PRESSURE DUE TO A PIECE OF FOREIGN OBJECT STUCK ON THE OIL PUMP PRESSURE RELIEF VALVE OR OCV. THE TEMPORARY ENTRY OF THE FOREIGN OBJECT TRIGGERS A MIL ILLUMINATION, BUT ROUGH IDLE WILL NOT BE PRODUCED UNTIL A LATER TIME. |
| 01-020-15-2930 | 2017-06-07. Service bulletin. ENGINE; EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL. SOME VEHICLES MAY EXPERIENCE THE CHECK ENGINE LIGHT ON WITH DTC P0300:00, P0301:00, P0302:00, P0303:00 AND/OR P0304:00 STORED IN MEMORY. • P0300:00: RANDOM MISFIRE DETECTED • P0301:00: CYLINDER NO.1 MISFIRE DETECTED • P0302:00: CYLINDER NO.2 MISFIRE DETECTED • P0303:00: CYLINDER NO.3 MISFIRE DETECTED • P0304:00: CYLINDER NO.4 MISFIRE DETECTED CARBON MAY BE DEPOSITED AROUND THE INTAKE VALVES, RESULTING IN UNSTABLE ENGINE COMBUSTION AND MISFIRING DURING THE ACCELERATED WARM-UP SYSTEM (AWS) OPERATION. |
| 01-023-15-3084 | 2017-05-31. Service bulletin. EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL; ENGINE. SOME VEHICLES MAY EXPERIENCE A ROUGH IDLE WITH THE MIL ON AND DTC P0015 / P0524 STORED IN MEMORY. • P0015:00 - EXHAUST CMP TIMING OVER-RETARDED • P0524:00 - ENGINE OIL PRESSURE TOO LOW THIS IS CAUSED BY A DROP IN ENGINE OIL PRESSURE DUE TO A PIECE OF FOREIGN OBJECT STUCK ON THE OIL PUMP PRESSURE RELIEF VALVE OR OCV. THE TEMPORARY ENTRY OF THE FOREIGN OBJECT TRIGGERS A MIL ILLUMINATION, BUT ROUGH IDLE WILL NOT BE PRODUCED UNTIL A LATER TIME. |
| 01-009-16-3172 | 2017-05-30. Service bulletin. EQUIPMENT ADAPTIVE/MOBILITY; ENGINE AND ENGINE COOLING; ENGINE. SOME VEHICLES MAY EXPERIENCE A ROUGH IDLE WITH THE CHECK ENGINE LIGHT ON AND DTC P0015 / P0524 STORED IN MEMORY.•P0015:00 - EXHAUST CMP TIMING OVER-RETARDED•P0524:00 - ENGINE OIL PRESSURE TOO LOWTHIS IS CAUSED BY A DROP IN ENGINE OIL PRESSURE DUE TO A PIECE OF FOREIGN OBJECT STUCK ON THE OIL PUMP PRESSURE RELIEF VALVE OR OIL CONTROL VALVE (OCV). THE TEMPORARY ENTRY OF THE FOREIGN OBJECT TRIGGERS A CHECK ENGINE LIGHT ON, BUT ROUGH IDLE WILL NOT BE PRODUCED UNTIL A LATER TIME. |
| 01-001-15-2988 | 2017-05-25. Service bulletin. ENGINE. SOME VEHICLES EQUIPPED WITH SKYACTIV-G 2.0L ENGINE MAY EXPERIENCE ENGINE OIL SEEPAGE FROM DRAIN PLUG AFTER THE ENGINE OIL IS REPLACED EVEN IF THE PLUG IS TIGHTENED TO THE SPECIFIED TORQUE WITH A NEW GASKET. OIL PAN DRAIN PLUG TIGHTENING TORQUE: 30—41 N·M {3.1—4.1 KGF·M, 23—30 FT·LBF} SEATING SURFACE OF THE OIL PAN FOR THE DRAIN PLUG MAY HAVE POOR FLATNESS DUE TO IMPROPER SPOT WELDING AND/OR THE SURFACE MAY HAVE GOTTEN A SCRATCH DURING MANUFACTURING PROCESS. |
| 01-014-15-3055 | 2017-05-17. Service bulletin. ENGINE. FREQUENT ENGINE STARTS UNDER EXTREMELY COLD AMBIENT TEMPERATURES MAY RESULT IN OIL SEEPAGE FROM THE ENGINE OIL PRESSURE SWITCH. THIS CONCERN MAY BE CAUSED BY A LACK OF DURABILITY OF THE OIL PRESSURE SWITCH UNDER THESE CONDITIONS. TO CORRECT THE PROBLEM, THE OIL PRESSURE SWITCH HAS BEEN IMPROVED TO INCREASE THE DURABILITY IN COLD AMBIENT TEMPERATURES. ALL SKYACTIV ENGINES EQUIPPED WITH OIL PRESSURE SWITCH PART NUMBER PE01-18-501A ARE APPLICABLE TO THIS ISSUE. |
| 01-005-15-3030A | 2017-05-16. Service bulletin. EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL; ENGINE. SOME VEHICLES MAY EXPERIENCE THE CHECK ENGINE LIGHT ON WITH DTC P0300:00, P0301:00, P0302:00, P0303:00 AND/OR P0304:00 STORED IN MEMORY AND ACCOMPANIED WITH AN INCREASED ENGINE OIL LEVEL. P0300:00: RANDOM MISFIRE DETECTED P0301:00: CYLINDER NO.1 MISFIRE DETECTED P0302:00: CYLINDER NO.2 MISFIRE DETECTED P0303:00: CYLINDER NO.3 MISFIRE DETECTED P0304:00: CYLINDER NO.4 MISFIRE DETECTED THIS IS CAUSED BY IMPROPER CONTROL LOGIC OF THE PCM. IN COLD WEATHER BELOW 14 °F (-10 °C) WITH REPEATED SHORT TIME OPERATION, EXCESS FUEL INJECTED IN THE CYLINDERS MAY ACCUMULATE IN THE CRANK CASE AND RESULT IN INCREASED OIL LEVEL AND MISFIRE. |
| 01-009-14-2909A | 2017-05-08. Service bulletin. ENGINE AND ENGINE COOLING:EXHAUST SYSTEM; EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL. SOME VEHICLES MAY EXPERIENCE A ROUGH IDLE WITH THE MIL ON AND DTC P0015 / P0524 STORED IN MEMORY.•P0015:00 - EXHAUST CMP TIMING OVER-RETARDED•P0524:00 - ENGINE OIL PRESSURE TOO LOWTHIS IS CAUSED BY A DROP IN ENGINE OIL PRESSURE DUE TO A PIECE OF FOREIGN OBJECT STUCK ON THE OIL PUMP PRESSURE RELIEF VALVE OR OCV. THE TEMPORARY ENTRY OF THE FOREIGN OBJECT TRIGGERS A MIL ILLUMINATION, BUT ROUGH IDLE WILL NOT BE PRODUCED UNTIL A LATER TIME. |
| 01-014-14-2932 | 2017-05-04. Service bulletin. FUEL SYSTEM, GASOLINE:STORAGE:TANK ASSEMBLY:FILLER PIPE AND CAP; ENGINE. SOME VEHICLES MAY EXHIBIT THE CHECK ENGINE LIGHT ON WITH DTC P0456 STORED IN THE PCM MEMORY.• P0456: EVAP SYSTEM LEAK DETECTED (VERY SMALL LEAK) THE CONCERN IS MOST LIKELY THE RESULT OF THE CUSTOMER NOT GETTING THE FUEL CAP COMPLETELY CLOSED AFTER FUELING THE VEHICLE. THIS CAUSES A SMALL FUEL VAPOR LEAK AND TURNS DTC P0456 ON. |
| 05-008-13-2861 | 2017-04-26. Service bulletin. ENGINE. SOME VEHICLES MAY EXHIBIT THE ATX FAIL-SAFE FUNCTION WORKING WITH THE FOLLOWING SYMPTOMS:•THE VEHICLE SPEED DOES NOT INCREASE WITH ENGINE SPEED•THE ATX DOES NOT SHIFT UP OR DOWN AS EXPECTEDTHE CONDITION MAY NOT ALWAYS BE ABLE TO BE REPRODUCED AND DTCS MAY NOT BE STORED WHEN THE VEHICLE IS BROUGHT IN. FOREIGN MATERIAL (IRON PARTICLES IN THE ATF) MAY ENTER THE ATX VALVE BODY AND CAUSE A TEMPORARY MALFUNCTION OF THE VALVE BODY AND/OR SENSOR (ATX FAIL-SAFE FUNCTION ACTIVATED). THE FAIL-SAFE FUNCTION IS CANCELED WITHOUT DTCS RECORDED IF THE MALFUNCTION GOES AWAY AND DOES NOT OCCUR AGAIN AT THE NEXT DRIVE CYCLE.FAIL-SAFE FUNCTION OPERATION:•IF A TECHNICAL FAULT IS DETECTED IN THE ATX BY THE MALFUNCTION DETECTION FUNCTION, THE FAIL-SAFE FUNCTION LIMITS THE ATX CONTROL (INHIBITS SOME GEARS OR SHIFT DOWN FUNCTIONS).•EVEN IN CASE OF AN ATX MALFUNCTION, THE FAIL-SAFE FUNCTION ALLOWS MINIMUM VEHICLE DRIVEABILITY. |
| 01-028-12-2722 | 2017-04-26. Service bulletin. ENGINE. SOME VEHICLES MAY EXPERIENCE A ROUGH IDLE WITH THE MIL ON AND DTC P0015 / P0524 STORED IN MEMORY. • P0015:00 - EXHAUST CMP TIMING OVER-RETARDED • P0524:00 - ENGINE OIL PRESSURE TOO LOW THIS IS CAUSED BY A DROP IN ENGINE OIL PRESSURE DUE TO A PIECE OF FOREIGN OBJECT STUCK ON THE OIL PUMP PRESSURE RELIEF VALVE OR OCV. THE TEMPORARY ENTRY OF THE FOREIGN OBJECT TRIGGERS A MIL ILLUMINATION, BUT ROUGH IDLE WILL NOT BE PRODUCED UNTIL A LATER TIME. |
| 01-021-12-2695B | 2017-04-25. Service bulletin. ENGINE. SOME VEHICLES MAY EXHIBIT A SQUEAK NOISE FROM THE ENGINE COMPARTMENT WHEN THE VEHICLE STARTS MOVING AND/OR AT THE TIME OF TRANSMISSION SHIFTING. THIS IS CAUSED BY STICK-SLIP NOISE OCCURING AT THE CONTACT SURFACES BETWEEN THE NO. 4 ENGINE MOUNT RUBBER AND THE NO. 4 ENGINE MOUNT BRACKET WHEN THE ENGINE SHAKES BACK AND FORTH. TO CORRECT THE PROBLEM, THE NO. 4 ENGINE MOUNT IS REPLACED AND GREASE IS APPLIED ON THE CONTACT SURFACES OF THE NO. 4 ENGINE MOUNT BRACKET. |
| 01-005-13-2738A | 2017-04-24. Service bulletin. ENGINE. SOME VEHICLES MAY EXPERIENCE DIFFICULTY WITH ENGINE STARTING IN THE WINTER (CRANKS BUT NO START), BUT CAN BE STARTED USING THE DE-CHOKE MODE WITH NO DTC RECORDED. THIS IS CAUSED BY IMPROPER CONTROL LOGIC OF THE PCM. TO CORRECT THE PROBLEM, THE CONTROL LOGIC OF THE PCM HAS BEEN CHANGED.DE-CHOKE MODE1.FULLY DEPRESS THE ACCELERATOR PEDAL AND CRANK THE ENGINE FOR 4 TO 5 SECONDS.2.TURN THE IGNITION SWITCH TO THE LOCK POSITION AND RELEASE THE ACCELERATOR PEDAL.3.START THE ENGINE WITHOUT DEPRESSING THE ACCELERATOR PEDAL. |
| 01-013-13-2791 | 2017-04-14. Service bulletin. ENGINE. SOME VEHICLES MAY EXHIBIT A SQUEAK NOISE FROM THE ENGINE COMPARTMENT WHEN THE VEHICLE STARTS MOVING AND/OR AT THE TIME OF TRANSMISSION SHIFTING. THIS IS CAUSED BY STICK-SLIP NOISE OCCURRING AT THE CONTACT SURFACES BETWEEN THE NO. 4 ENGINE MOUNT RUBBER AND THE NO. 4 ENGINE MOUNT BRACKET WHEN THE ENGINE SHAKES BACK AND FORTH. |
| 01-005-13-2738 | 2017-04-13. Service bulletin. ENGINE. SOME VEHICLES MAY EXPERIENCE DIFFICULTY WITH ENGINE STARTING IN THE WINTER (CRANKS BUT NO START), BUT CAN BE STARTED USING THE DE-CHOKE MODE WITH NO DTC RECORDED. THIS IS CAUSED BY IMPROPER CONTROL LOGIC OF THE PCM. TO CORRECT THE PROBLEM, THE CONTROL LOGIC OF THE PCM HAS BEEN CHANGED.DE-CHOKE MODE1.FULLY DEPRESS THE ACCELERATOR PEDAL AND CRANK THE ENGINE FOR 4 TO 5 SECONDS.2.TURN THE IGNITION SWITCH TO THE LOCK POSITION AND RELEASE THE ACCELERATOR PEDAL.3.START THE ENGINE WITHOUT DEPRESSING THE ACCELERATOR PEDAL. |
| 01-009-16-3172A | 2017-02-28. Service bulletin. ENGINE. SOME VEHICLES MAY EXPERIENCE A ROUGH IDLE WITH THE CHECK ENGINE LIGHT ON AND DTC P0015 / P0524 STORED IN MEMORY.•P0015:00 - EXHAUST CMP TIMING OVER-RETARDED•P0524:00 - ENGINE OIL PRESSURE TOO LOWTHIS IS CAUSED BY A DROP IN ENGINE OIL PRESSURE DUE TO A PIECE OF FOREIGN OBJECT STUCK ON THE OIL PUMP PRESSURE RELIEF VALVE OR OIL CONTROL VALVE (OCV). THE TEMPORARY ENTRY OF THE FOREIGN OBJECT TRIGGERS A CHECK ENGINE LIGHT ON, BUT ROUGH IDLE WILL NOT BE PRODUCED UNTIL A LATER TIME. |
| 01-009-16-3172B | 2017-02-24. Service bulletin. ENGINE. SOME VEHICLES MAY EXPERIENCE A ROUGH IDLE WITH THE CHECK ENGINE LIGHT ON AND DTC P0015 / P0524 STORED IN MEMORY.•P0015:00 - EXHAUST CMP TIMING OVER-RETARDED•P0524:00 - ENGINE OIL PRESSURE TOO LOWTHIS IS CAUSED BY A DROP IN ENGINE OIL PRESSURE DUE TO A PIECE OF FOREIGN OBJECT STUCK ON THE OIL PUMP PRESSURE RELIEF VALVE OR OIL CONTROL VALVE (OCV). THE TEMPORARY ENTRY OF THE FOREIGN OBJECT TRIGGERS A CHECK ENGINE LIGHT ON, BUT ROUGH IDLE WILL NOT BE PRODUCED UNTIL A LATER TIME. |
| 1080M | 2017-02-23. Service bulletin. ENGINE. IF AN ENGINE ASSEMBLY IS REPLACED AFTER A CATASTROPHIC INTERNAL MECHANICAL FAILURE, CLEAN THE INTAKE MANIFOLD INTERNALLY BEFORE INSTALLING A REPLACEMENT ENGINE ASSEMBLY. IF THE INTAKE MANIFOLD IS NOT CLEANED PROPERLY, THE REPLACEMENT ENGINE MAY FAIL PREMATURELY.METALLIC DEBRIS FROM THE OLD ENGINE (WITH CATASTROPHIC INTERNAL MECHANICAL FAILURE) MAY REST INSIDE THE INTAKE MANIFOLD. WHEN THE NEW ENGINE ASSEMBLY IS INSTALLED, DEBRIS IN THE INTAKE MANIFOLD WILL BE INGESTED INTO THE NEW ENGINE AND CAUSE INTERNAL DAMAGE.CLEAN THE INTAKE MANIFOLD INTERNALLY TO REMOVE ANY DEBRIS FROM OLD ENGINE BEFORE INSTALLING THE NEW REPLACEMENT ENGINE ASSEMBLY.IF THE INTAKE MANIFOLD CANNOT BE PROPERLY CLEANED INTERNALLY, REPLACE IT. |
| 01-016-16-3220 | 2017-02-23. Service bulletin. ENGINE. THERE IS A CONCERN THAT SOME WATER PUMPS ARE BEING REPLACED THAT ARE NOT FAULTY, DUE TO SIGNS OF A VERY SMALL COOLANT LEAK FROM THE BLEED HOLE. THIS SERVICE BULLETIN IS TO INFORM YOU ABOUT THE WATER PUMP SEALING MECHA-NISM AND THE CRITERIA IF REPLACEMENT IS NECESSARY OR NOT. |
| 1102M | 2017-02-21. Service bulletin. ENGINE. WORKSHOP MANUAL EVAP SYSTEM LEAK INSPECTION USING THE M-MDS HAS BEEN DISCONTINUED FOR SOME MODELS. INSTEAD, THE WORKSHOP MANUAL EVAP SYSTEM LEAK INSPECTION USING EVAP LEAK TESTER WILL BE USED TO TROUBLESHOOT EVAP SYSTEM LEAKS. |
| RF-16-03 | 2017-02-18. Service bulletin. ENGINE. THE 2016 CX-9 WITH THE SKYACTIV®-G 2.5T ENGINE REQUIRES A UNIQUE OIL FILTER (PY8W-14-302) WHICH IS NOT INTERCHANGEABLE WITH OTHER SKYACTIV® OIL FILTERS. THE UNIQUE OIL FILTER CAN BE IDENTIFIED WITH TWO WHITE BANDS AS SHOWN BELOW. |
The summaries are NHTSA's. Each bulletin's page links NHTSA's copy of the manufacturer's document.