Service bulletins for the 2018 Mazda Mazda2
A bulletin is a manufacturer's communication to its dealers, as NHTSA indexes it. The summary is NHTSA's. The document is the manufacturer's: read it at NHTSA. A bulletin is not a recall, and listing a model year does not mean every vehicle of it is concerned.
108 on file from NHTSA, as of 2026-10-19.
By type
By component
By trouble code
By topic
Only bulletins with component: Equipment and accessories are shown. Show all
| 09-003-20-3671 | 2020-01-23. Service bulletin. EQUIPMENT; ELECTRICAL SYSTEM. In accordance with Federal regulations, follow the procedure listed below when replacing a speedometer. NOTE: Tampering with a motor vehicle odometer is strictly prohibited by Federal, and State laws. It is the dealer’s responsibility to comply with Federal, State, and local laws concerning odometer and related documentation requirements when providing a repair or replacement. • Mazda vehicles are manufactured with tamper-proof speedometers. • When a speedometer is replaced, the new speedometer will read zero (0) miles. • This procedure is extremely important to accurately represent actual vehicle mileage. • Prior to speedometer removal, complete the information required on the “Speedometer Replacement Label”. Labels can only be ordered through Mazda eStore. • In an effort to achieve a higher level of Customer Experience and retain the value of Mazda’s vehicles, MNAO Warranty Operations is allowing all Mazda dealers to utilize a third party, SPECMO Enterprises, Inc., for Instrument Panel Cluster (IPC) odometer setting service. With the use of SPECMO’s services, it is possible that the odometer will be set between 10 to 31 miles over the odometer mileage at the time of replacement for both warranty and customer pay repairs. Please make sure that the customer is aware that there may be a slight variance to the odometer, in which case the customer may have to accept the slightly higher mileage. Since odometer setting service is not part of the warranty repair, it is not warrantable nor required, but optional. However, Mazda Warranty policy provides after- warranty assistance (AWA) or DSA that can be utilized to cover this service expense. |
|---|---|
| MT-002-19 | 2019-12-20. Service bulletin. ENGINE AND ENGINE COOLING; EQUIPMENT. If an engine assembly is replaced after a catastrophic internal mechanical failure, clean the intake manifold internally before installing a replacement engine assembly. If the intake manifold is not cleaned properly, the replacement engine may fail prematurely. Metallic debris from the old engine (with catastrophic internal mechanical failure) may rest inside the intake manifold. When the new engine assembly is installed, debris in the intake manifold will be ingested into the new engine and cause internal damage. |
| 09-031-19-3625 | 2019-08-15. Service bulletin. ELECTRICAL SYSTEM; EQUIPMENT. After the installation of a new instrument cluster, the message "Fctry" or “Factory” is displayed instead of the odometer. This concern may also occur when a room fuse is installed in a new vehicle. Some new instrument clusters are in the factory mode setting. Factory mode cancellation is required. NOTE: The concern is applicable to Calsonic Kansei instrument clusters. Not all trim levels are affected. |
| MT-001-18 | 2018-04-23. Service bulletin. EQUIPMENT:ELECTRICAL. When installing a navigation SD card, the center display may show error message "Invalid SD Card". |
| SA-065-17 | 2017-10-04. Service bulletin. EQUIPMENT:ELECTRICAL. Use the symptom troubleshooting tables below to diagnose MAZDA CONNECT concerns. MAZDA CONNECT Symptom Troubleshooting Table Sections: Audio System, Bluetooth®, Center Display, DTC, i-ACTIVESENSE, Maintenance Monitor, Navigation, Noise, Reboot / Frozen Screen / Slow Response, USB / Aux, Voice Command |
| MT-015-17 | 2017-08-10. Service bulletin. EQUIPMENT:ELECTRICAL; EQUIPMENT ADAPTIVE/MOBILITY. Some customers may complain about the following MAZDA CONNECT Temperature Warning message: Display is too Hot. Screen performance may be decreased until it cools. The warning message displays when the MAZDA CONNECT screen temperature is above 176 degrees Fahrenheit (80 degrees Celsius). |
| SA-063-17 | 2017-08-10. Service bulletin. ELECTRICAL SYSTEM:SOFTWARE; EQUIPMENT:ELECTRICAL. Some customers may complain about the "wrong" phone is connected to the infotainment system. MAZDA CONNECT bluetooth will connect all profiles to devices in order of priority if the last device is not available. This concern may be a normal operation of the CMU connecting to available devices on start up. |
The summaries are NHTSA's. Each bulletin's page links NHTSA's copy of the manufacturer's document.