Service bulletins for the 2013 Mazda CX-9
A bulletin is a manufacturer's communication to its dealers, as NHTSA indexes it. The summary is NHTSA's. The document is the manufacturer's: read it at NHTSA. A bulletin is not a recall, and listing a model year does not mean every vehicle of it is concerned.
319 on file from NHTSA, as of 2026-10-19.
By type
By component
By trouble code
By topic
| 01-024-15-3110 | 2017-06-08. Service bulletin. EQUIPMENT ADAPTIVE/MOBILITY. SOME VEHICLES MAY EXHIBIT AN UNUSUAL RATTLE/BUZZING TYPE NOISE FROM THE PRESILENCER WHEN DRIVING AT APPROXIMATELY 1800 RPM. THE LOWER (REAR-SIDE) OF THE PRE-SILENCER MAY BE THERMALLY DEFORMED DUE TO INSUFFICIENT RIGIDITY (FEWER WELD SPOTS). THE DEFORMED PORTION MAY RESONATE EXHAUST GAS PULSATIONS, WHICH CAUSES NOISE. A REINFORCED PLATE HAS BEEN ADDED TO THE PRE-SILENCER TO INCREASE THE RIGIDITY, THEREBY ELIMINATING DEFORMATION. |
|---|---|
| 03-007-15-3091 | 2017-06-07. Service bulletin. ENGINE AND ENGINE COOLING:EXHAUST SYSTEM. SOME VEHICLES MAY EXPERIENCE VIBRATION DURING ACCELERATION AND/OR NOISE COMING FROM THE REAR OF THE VEHICLE. DUE TO ENVIRONMENTAL HEAT AND HEAT FROM THE EXHAUST SYSTEM, THE REAR DIFFERENTIAL MOUNTING RUBBER MAY BECOME HARDENED AND CRACKED, RESULTING IN VIBRATION AND/OR NOISE. TO ELIMINATE THIS CONCERN, THE RUBBER MATERIAL HAS BEEN IMPROVED. |
| 09-030-15-3073 | 2017-06-07. Service bulletin. EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL. MAZDA INFOTAINMENT SYSTEMS REQUIRE CONTACTING THE PROPER SOURCE FOR DIAGNOSTIC SUPPORT, PARTS AUTHORIZATION, AND PARTS EXCHANGE. SOME COMPONENTS REQUIRE PRIOR AUTHORIZATION BEFORE ORDERING AS EXCHANGE. REFER TO DAG EXCHANGE CENTRAL (MXCONNECT>PARTS AND ACCESSORIES>PARTS>PROGRAMS>EXCHANGE CENTRAL) FOR COMPONENT AVAILABILITY, SOURCE OF TECHNICAL SUPPORT AND PRIOR AUTHORIZATION REQUIREMENT. NOTE: ALWAYS CHECK FOR A TSB THAT MAY MODIFY OR ELIMINATE PRIOR AUTHORIZATION FOR A SPECIFIC SYMPTOM FOR A GIVEN COMPONENT. |
| 09-031-15-3076 | 2017-06-07. Service bulletin. EQUIPMENT:ELECTRICAL:NAVIGATIONAL SYSTEM(GLOBAL POSITIONING SYSTEM). THE NAVIGATION SYSTEM SUPPORT FOR DIAGNOSTICS, PARTS AUTHORIZATION, AND PARTS EXCHANGE REQUIRE CONTACTING THE PROPER SOURCE. • TOMTOM NAVIGATION HELP DESK AT 866-486-6866 FROM 7AM-11PM (M-F) AND 9AM-8PM (SAT) EASTERN STANDARD TIME. NOTE: ONE OF THE FIRST STEPS FOR TROUBLESHOOTING THE NAVIGATION SYSTEM IS FOR THE CUSTOMER OR DEALER TO CALL TOMTOM. IF THE TOMTOM CALL CENTER CANNOT SOLVE THE CUSTOMER’S PROBLEM, THEY WILL PROVIDE A CASE NUMBER TO THE CUSTOMER THAT CAN BE REFERRED TO IF NEEDED. SERVICE ADVISORS SHOULD GET THIS CASE NUMBER FROM THE CUSTOMER IF THE VEHICLE COMES INTO THE DEALER FOR FURTHER DIAGNOSIS SO THE TECHNICIAN CAN HAVE IT WHEN CALLING TOMTOM. |
| 09-008-15-2991C | 2017-06-07. Service bulletin. EQUIPMENT:ELECTRICAL:RADIO/TAPE DECK/CD ETC.. SOME CUSTOMERS MAY COMPLAIN ABOUT ONE OR MORE OF THE FOLLOWING CONCERNS. 1. SMS/TEXT CANNOT BE DOWNLOADED WHEN ONNECTED VIA BLUETOOTH. 2. OPERATIONAL CONCERNS WHEN PLAYING A MEDIA DEVICE (IPOD, USB STICK ETC.) CONNECTED VIA THE USB PORT. A. AFTER THE IGNITION IS TURNED ON, IT TAKES A LONG TIME TO LOAD ALL THE DATA FROM THE DEVICE BEFORE STARTING PLAYBACK. DEPENDING ON THE DATA VOLUME, IT CAN TAKE UP TO SEVERAL MINUTES. B. AFTER THE IGNITION IS TURNED ON, THE PLAYBACK ALWAYS STARTS FROM THE FIRST TRACK. IT DOES NOT START FROM THE LAST PLAYING TRACK/POSITION WHEN THE IGNITION WAS TURNED OFF. C. “IPOD ERROR” MESSAGE FOR THE APPLE® IOS 8.0 OR HIGHER SOFTWARE ON IPHONE 4, 5, OR 6. THESE CONCERNS MAY BE CAUSED BY THE SOFTWARE OF THE BLUETOOTH/HANDS-FREE MODULE THAT CONTROLS THE USB CONNECTION. TO IMPROVE THESE CONCERNS, THE SOFTWARE OF THE BLUETOOTH/HANDS-FREE MODULE HAS BEEN CHANGED. NOTE: • THE UPDATED SOFTWARE OF THE BLUETOOTH/HANDS-FREE MODULE WILL ONLY ADDRESS SMS/TEXT CONCERNS FOR THE APPLE® IPHONE AT THIS TIME. |
| 01-008-15-3045 | 2017-06-07. Service bulletin. EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL. SOME VEHICLES MAY EXHIBIT THE CHECK ENGINE LIGHT ON WITH DTC P0456 STORED IN THE PCM MEMORY. • P0456: EVAP SYSTEM LEAK DETECTED (VERY SMALL LEAK) THE CONCERN IS MOST LIKELY THE RESULT OF THE CUSTOMER NOT GETTING THE FUEL CAP COMPLETELY CLOSED AFTER FUELING THE VEHICLE. THIS CAUSES A SMALL FUEL VAPOR LEAK AND TURNS DTC P0456 ON. |
| 09-017-15-3023 | 2017-06-07. Service bulletin. VISIBILITY:POWER WINDOW DEVICES AND CONTROLS. SOME CUSTOMERS MAY NOTICE THE POWER WINDOW(S) ARE EITHER NOISY OR COMPLETELY INOPERATIVE WHILE OPERATING THE POWER WINDOW SWITCH. THIS MAY BE DUE TO THE POWER WINDOW MOTOR GEAR HAVING CHIPPED OR DAMAGED TEETH. TO ELIMINATE THIS CONCERN, THE POWER WINDOW MOTOR HAS BEEN IMPROVED BY REDUCING THE FORCE APPLIED TO THE GEAR WHEN THE WINDOW IS CLOSED. |
| 01-010-15-3040 | 2017-06-07. Service bulletin. FUEL SYSTEM, OTHER. SOME VEHICLES MAY EXHIBIT AN UNUSUAL NOISE WHILE DRIVING THE VEHICLE. THE NOISE MAY BE CAUSED BY A BROKEN FUEL TANK (B) INSULATOR (A) THAT IS HANGING DOWN AND CONTACTING THE PROPELLER SHAFT. THE RIVETS (C) MAY BREAK WHEN A LOAD OCCURS. THE RIVET MATERIAL HAS BEEN CHANGED TO ELIMINATE THIS CONCERN. |
| 01-008-16-3162 | 2017-06-06. Service bulletin. ENGINE. SOME VEHICLES MAY EXHIBIT AN ENGINE COOLANT LEAK (A) BETWEEN THE LOWER RADIATOR HOSE (B) AND THE THERMOSTAT HOUSING (C). THE LOWER RADIATOR HOSE HAS BEEN MODIFIED TO IMPROVE SEALING PERFORMANCE. |
| 09-038-15-3080 | 2017-05-31. Service bulletin. LATCHES/LOCKS/LINKAGES:DOORS:LATCH. SOME CUSTOMERS MAY COMPLAIN THAT THE DOORS DO NOT LOCK / UNLOCK WHEN PRESSING THE REQUEST SWITCH. THIS MAY BE CAUSED BY A TORN OR CRACKED REQUEST SWITCH RUBBER BUTTON (A). THE RUBBER SURFACE OF THE REQUEST SWITCH MAY BECOME GRADUALLY WORN OUT BY REPEATED USE. WATER MAY ENTER THE REQUEST SWITCH AND CAUSE A SHORT-CIRCUIT OF THE ELECTRICAL SYSTEM. TO ELIMINATE THIS CONCERN, THE THICKNESS OF THE RUBBER BUTTON HAS BEEN INCREASED FROM 0.6 MM TO 1.8 MM TO IMPROVE WEAR RESISTANCE. |
| 09-017-16-3169 | 2017-05-30. Service bulletin. VISIBILITY:GLASS, SIDE/REAR; STRUCTURE:BODY:DOOR. SOME VEHICLES MAY EXHIBIT A RATTLE NOISE AND/OR WIND NOISE FROM THE FRONT DOOR GLASS AREA WHILE DRIVING THE VEHI-CLE. THIS IS CAUSED BY A DEFORMED GLASS RUN CHANNEL (A). THE DEFORMED AREA IS LOCATED AT THE UPPER REAR CORNER OF THE RUN CHANNEL AND IS CAUSED BY REPEATED DOOR GLASS CLOSURES IN VERY HOT CLIMATES. THE DEFORMED AREA CAUSES POOR CONTACT BETWEEN THE GLASS RUN CHANNEL AND THE DOOR SASH, WHICH RESULTS IN RATTLE NOISE AND/OR WIND NOISE. |
| 02-009-16-3155 | 2017-05-30. Service bulletin. STEERING: STEERING WHEEL/HANDLE BAR. SOME CUSTOMERS MAY COMPLAIN THAT THE STEERING WHEEL IS OFF CENTER MORE THAN 3° EVEN WHEN DRIVING STRAIGHT ON A FLAT ROAD. |
| 05-001-16-3128 | 2017-05-26. Service bulletin. EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL. ALWAYS BE SURE TO USE THE CORRECT AUTOMATIC TRANSMISSION FLUID WHEN REPLACING ATF. USING THE WRONG ATF MAY CAUSE SHIFT QUALITY COMPLAINTS OR MAY EVEN DAMAGE THE TRANSMISSION.NOTE:• ATF M-V (TYPE M5) IS NOT THE SAME FLUID AS MERCON®V OR MERCON®LV ATF.• ATF M-V (TYPE M5) HAS A GREATER VISCOSITY THAN MERCON®V AND MERCON®LV ATF IN LOW TEMPERATURES.• ATF M-V (TYPE M5) HAS A GREATER ANTI-JUDDER SPECIFICATION THAN MERCON®V AND MERCON®LV ATF.• TRANSMISSION FLUID FLUSHING SHOULD ONLY BE PERFORMED WHEN INSTRUCTED BY THE WORKSHOP MANUAL OR ANY OTHER MAZDA PUBLICATION. CAUTION:• USING ATF OTHER THAN ATF M-V (TYPE M5) IN AUTOMATIC TRANSMISSIONS DESIGNED TO USE ATF M-V (TYPE M5) MAY CAUSE SHIFT QUALITY COMPLAINTS.• USING ANY OTHER ATF OTHER THAN THE SPECIFIED ATF IN AUTOMATIC TRANSMISSIONS MAY CAUSE TRANSMISSION DAMAGE.• USING A GENERIC, MULTI-PURPOSE OR UNIVERSAL ATF MAY CAUSE TRANSMISSION DAMAGE.• DAMAGE TO THE TRANSMISSION CAUSED BY USING THE INCORRECT ATF, OR A GENERIC, MULTI-PURPOSE OR UNIVERSAL ATF WILL NOT BE COVERED BY WARRANTY. |
| 09-003-16-3130 | 2017-05-26. Service bulletin. EXTERIOR LIGHTING:TAIL LIGHTS; EXTERIOR LIGHTING:HEADLIGHTS. SOME CUSTOMERS MAY COMPLAIN OF CONDENSATION/FOG INSIDE THE FRONT (HEADLAMP/HEADLIGHT) OR REAR (TAILLAMP/TAIL-LIGHT) COMBINATION LIGHTS. THE RECENT NEW MODELS HAVE BEEN FITTED WITH A CLEAR LENS WHICH CAN CAUSE THE SYMP-TOM TO BE MORE NOTICEABLE, HOWEVER, IT DOES NOT AFFECT THE PERFORMANCE OF THE LIGHT. THIS CONDENSATION/FOG IS A NATURAL PHENOMENON THAT OCCURS WHEN THERE IS A FAIRLY LARGE TEMPERATURE DIFFERENCE BETWEEN THE INSIDE AND THE OUTSIDE OF THE LIGHT HOUSING. IT IS NORMAL FOR VERY SMALL WATER DROPS TO APPEAR IN CERTAIN LOCATIONS ON THE LIGHT UNITS WHERE THE AIR IS STAGNANT (CONDENSATION), MAKING THE LENS LOOK WHITISH (FOG). THIS HAPPENS MOSTLY IN THE CORNERS AND NARROW SPACES, AND WILL TYPICALLY CLEAR DURING WARMER AMBIENT TEMPERATURES, OR WHEN THE LIGHTS HAVE BEEN ON FOR SOME TIME. EXPLAIN TO THE CUSTOMER THAT THIS IS A NATURAL PHENOMENON AND NOT A QUALITY DEFECT. DO NOT ATTEMPT REPAIRS AS THIS IS CONSIDERED NORMAL, AND IS NOT COVERED UNDER WARRANTY. REPLACING THE LIGHT UNIT WILL NOT CORRECT THIS SYMPTOM. |
| 09-007-15-3011 | 2017-05-25. Service bulletin. ELECTRICAL SYSTEM:SOFTWARE. SOME VEHICLES MAY HAVE THE BLIND SPOT MONITORING (BSM) OFF INDICATOR LIGHT FLASHING AND DTC U3000:54 STORED IN MEMORY. THE CONCERN IS CAUSED BY INADEQUATE BSM CONTROL MODULE CONTROL LOGIC. THE BSM CONTROL MODULE SOFTWARE HAS BEEN UPDATED TO ELIMINATE THIS CONCERN. |
| 09-008-15-2991 | 2017-05-25. Service bulletin. ELECTRICAL SYSTEM:SOFTWARE. SOME CUSTOMERS MAY COMPLAIN ABOUT ONE OR MORE OF THE FOLLOWING CONCERNS. 1. SMS/TEXT CANNOT BE DOWNLOADED WHEN CONNECTED VIA BLUETOOTH. 2. OPERATIONAL CONCERNS WHEN PLAYING A MEDIA DEVICE (IPOD, USB STICK ETC.) CONNECTED VIA THE USB PORT. A. AFTER THE IGNITION IS TURNED ON, IT TAKES A LONG TIME TO LOAD ALL THE DATA FROM THE DEVICE BEFORE STARTING PLAYBACK. DEPENDING ON THE DATA VOLUME, IT CAN TAKE UP TO SEVERAL MINUTES. B. AFTER THE IGNITION IS TURNED ON, THE PLAYBACK ALWAYS STARTS FROM THE FIRST TRACK. IT DOES NOT START FROM THE LAST PLAYING TRACK/POSITION WHEN THE IGNITION WAS TURNED OFF. THESE CONCERN MAY BE CAUSED BY THE SOFTWARE OF THE BLUETOOTH/HANDS-FREE MODULE THAT CONTROLS THE USB CONNECTION. TO IMPROVE THESE CONCERNS, THE SOFTWARE OF THE BLUETOOTH/HANDS-FREE MODULE HAS BEEN CHANGED. NOTE: THE UPDATED SOFTWARE OF THE BLUETOOTH/HANDS-FREE MODULE WILL ONLY ADDRESS SMS/TEXT CONCERNS FOR THE APPLE® IPHONE AT THIS TIME. |
| 01-003-15-3014 | 2017-05-25. Service bulletin. EQUIPMENT. USE THE FOLLOWING REPAIR PROCEDURE TO MINIMIZE THE NEED TO REPLACE THE CATALYST CONVERTER/EXHAUST PIPE WHEN REMOVING OXYGEN SENSORS AND/OR AIR FUEL RATIO SENSORS. |
| 03-005-15-3016 | 2017-05-25. Service bulletin. EQUIPMENT ADAPTIVE/MOBILITY. IF REPLACEMENT OF THE RIGHT SIDE (RH) TRANSFER OIL SEAL (A), AND TRANSFER DUST SEAL (B) ARE NECESSARY, USE THE FOLLOWING REPAIR PROCEDURE TO INSTALL THE NEW OIL SEALS. |
| 01-006-15-3039 | 2017-05-19. Service bulletin. EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL. SOME VEHICLES MAY EXPERIENCE MIL ILLUMINATION WITH DTC P219A:00 AND/OR P219B:00 STORED IN PCM MEMORY. THE DTCS MAY BE CAUSED BY ABNORMAL ELECTRICAL NOISE WITHIN THE ENGINE HARNESS OF CERTAIN VEHICLES. TO ELIMINATE THIS CONCERN, SEPARATE THE A/F SENSOR SIGNAL LINES FROM THE EMISSION HARNESS BY INSTALLING THE SHORT CORD SERVICE PART DETAILED IN THIS BULLETIN. |
| 06-003-14-2984 | 2017-05-19. Service bulletin. EQUIPMENT ADAPTIVE/MOBILITY. SOME VEHICLES MAY EXHIBIT AN ABNORMAL STEERING FEEL AND/OR NOISE WHILE DRIVING THE VEHICLE IN FREEZING TEMPERA-TURES, HOWEVER, THERE IS NO LOSS OF STEERING CONTROL.THIS MAY BE DUE TO OIL SEEPAGE FROM THE POWER STEERING OIL PUMP PRESSURE SWITCH (A). THE OIL SEEPAGE IS CAUSED BY POOR SEALING OF THE OIL PRESSURE SWITCH O-RING AT LOW TEMPERATURE. THE SHAPE AND MATERIAL OF THE O-RING HAS BEEN CHANGED TO IMPROVE LOW TEMPERATURE SEALING PERFORMANCE. |
| 09-008-15-2991A | 2017-05-18. Service bulletin. ELECTRICAL SYSTEM:SOFTWARE; EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL. SOME CUSTOMERS MAY COMPLAIN ABOUT ONE OR MORE OF THE FOLLOWING CONCERNS. 1. SMS/TEXT CANNOT BE DOWNLOADED WHEN CONNECTED VIA BLUETOOTH. 2. OPERATIONAL CONCERNS WHEN PLAYING A MEDIA DEVICE (IPOD, USB STICK ETC.) CONNECTED VIA THE USB PORT. A. AFTER THE IGNITION IS TURNED ON, IT TAKES A LONG TIME TO LOAD ALL THE DATA FROM THE DEVICE BEFORE STARTING PLAYBACK. DEPENDING ON THE DATA VOLUME, IT CAN TAKE UP TO SEVERAL MINUTES. B. AFTER THE IGNITION IS TURNED ON, THE PLAYBACK ALWAYS STARTS FROM THE FIRST TRACK. IT DOES NOT START FROM THE LAST PLAYING TRACK/POSITION WHEN THE IGNITION WAS TURNED OFF. THESE CONCERN MAY BE CAUSED BY THE SOFTWARE OF THE BLUETOOTH/HANDS-FREE MODULE THAT CONTROLS THE USB CONNECTION. TO IMPROVE THESE CONCERNS, THE SOFTWARE OF THE BLUETOOTH/HANDS-FREE MODULE HAS BEEN CHANGED. NOTE: • THE UPDATED SOFTWARE OF THE BLUETOOTH/HANDS-FREE MODULE WILL ONLY ADDRESS SMS/TEXT CONCERNS FOR THE APPLE® IPHONE AT THIS TIME. • THE UPDATED SOFTWARE OF THE BLUETOOTH/HANDSFREE MODULE WILL NOT ADDRESS THE “IPOD ERROR” MESSAGE CONCERN FOR THE APPLE® IOS 8.0 OR HIGHER SOFTWARE ON IPHONE 4, 5, OR 6 AT THIS TIME. |
| 09-008-15-2991B | 2017-05-18. Service bulletin. EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL; ELECTRICAL SYSTEM:SOFTWARE. SOME CUSTOMERS MAY COMPLAIN ABOUT ONE OR MORE OF THE FOLLOWING CONCERNS. 1. SMS/TEXT CANNOT BE DOWNLOADED WHEN CONNECTED VIA BLUETOOTH. 2. OPERATIONAL CONCERNS WHEN PLAYING A MEDIA DEVICE (IPOD, USB STICK ETC.) CONNECTED VIA THE USB PORT. A. AFTER THE IGNITION IS TURNED ON, IT TAKES A LONG TIME TO LOAD ALL THE DATA FROM THE DEVICE EFORE STARTING PLAYBACK. DEPENDING ON THE DATA VOLUME, IT CAN TAKE UP TO SEVERAL MINUTES. B. AFTER THE IGNITION IS TURNED ON, THE PLAYBACK ALWAYS STARTS FROM THE FIRST TRACK. IT DOES NOT START FROM THE LAST PLAYING TRACK/POSITION WHEN THE IGNITION WAS TURNED OFF. C. “IPOD ERROR” MESSAGE FOR THE APPLE® IOS 8.0 OR HIGHER SOFTWARE ON IPHONE 4, 5, OR 6. THESE CONCERNS MAY BE CAUSED BY THE SOFTWARE OF THE BLUETOOTH/HANDS-FREE MODULE THAT CONTROLS THE USB CONNECTION. TO IMPROVE THESE CONCERNS, THE SOFTWARE OF THE BLUETOOTH/HANDS-FREE MODULE HAS BEEN CHANGED. NOTE: • THE UPDATED SOFTWARE OF THE BLUETOOTH/HANDS-FREE MODULE WILL ONLY ADDRESS SMS/TEXT CONCERNS FOR THE APPLE® IPHONE AT THIS TIME. |
| 04-001-15-3053 | 2017-05-17. Service bulletin. SERVICE BRAKES, HYDRAULIC:FLUID. SOME VEHICLES MAY EXHIBIT BRAKE FLUID SEEPAGE FROM THE BRAKE MASTER CYLINDER RESERVE TANK CAP. THE UPPER SURFACE OF THE RESERVE TANK MAY APPEAR DUSTY OR DIRTY WHERE THE BRAKE FLUID SEEPAGE HAS OCCURRED. THIS CONCERN MAY BE CAUSED BY A DECREASE IN SEALING PERFORMANCE OF CAP DUE TO AGING DETERIORATION. A NEW CAP WITH IMPROVED SEALING PERFORMANCE HAS BEEN ESTABLISHED AS A SERVICE PART |
| 09-024-15-3050 | 2017-05-17. Service bulletin. VISIBILITY:POWER WINDOW DEVICES AND CONTROLS. SOME CUSTOMERS MAY EXPERIENCE INOPERATIVE FRONT DOOR WINDOW AUTO-CLOSING OPERATION WHEN USING THE WINDOW SWITCHES (A). THE WINDOW MOVES UPWARD, BUT AUTOMATICALLY RETURNS TO THE HALFWAY POSITION (AS IF THE JAM-SAFE WINDOW FUNCTION IS OPERATING). THE GLASS RUN CHANNEL MAY BE DEFORMED CAUSING INCREASED SLIDING RESISTANCE AGAINST THE WINDOW GLASS. THIS MAY CAUSE THE SYSTEM TO MIS-JUDGE THAT SOMETHING IS BLOCKING THE WINDOW CLOSE MOVEMENT AND OPERATES THE JAM-SAFE WINDOW FUNCTION. |
| 01-012-15-3052 | 2017-05-16. Service bulletin. EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL. SOME VEHICLES MAY EXPERIENCE A LACK OF POWER AND THE WRENCH LIGHT COMES ON WITH DTCS P0123 / P0222 STORED IN MEMORY. WRENCH LIGHT: POWERTRAIN MALFUNCTION / REDUCED POWER WARNING LIGHT • DTC: P0123:00 TP SENSOR NO.1 CIRCUIT HIGH INPUT. • DTC: P0222:00 TP SENSOR NO. 2 CIRCUIT LOW INPUT. TO ELIMINATE THIS CONCERN, THE EMISSIONS HARNESS HAS BEEN IMPROVED. |
The summaries are NHTSA's. Each bulletin's page links NHTSA's copy of the manufacturer's document.