WenmarOpen by Wenmar Pro

Service bulletins for the 2026 Mazda CX-70

A bulletin is a manufacturer's communication to its dealers, as NHTSA indexes it. The summary is NHTSA's. The document is the manufacturer's: read it at NHTSA. A bulletin is not a recall, and listing a model year does not mean every vehicle of it is concerned.

121 on file from NHTSA, as of 2026-10-19.

By type

By component

By trouble code

By topic

Only bulletins with component: Body and frame are shown. Show all

Bulletins, newest first
SA-056-262026-09-04. Service bulletin. STRUCTURE:BODY; FUEL/PROPULSION SYSTEM. DESCRIPTION Some customers will report that their fuel filler lid (door) was stuck closed and would not open to refuel the vehicle. The fuel door may or may not be missing. REPAIR PROCEDURE 1. Check the system operation as noted in the PHEV Refueling Procedure and check for DTC.
09-018-262026-06-02. Service bulletin. STRUCTURE:BODY. This bulletin supersedes the previously issued bulletin(s) listed below. The changes are noted in Red. 09-031/25 08/05/25 DESCRIPTION While driving on gravel or dusty roads, dust accumulates at the lower inner edge of the door garnish. When the rear door is opened, the dust may be blown up and enter the cabin, adhering to the seats and the floor. This is caused by a large gap at the lower part of the boundary between the rear door and the front door, and air containing dust and/or sand is sucked up into the gap, accumulating at the lower edge of the rear door garnish while driving. To eliminate this concern, a mass production change is under study. NOTE: In environments where passengers frequently enter and exit the vehicle under dusty conditions (e.g. dirt or gravel roads, off-road driving), a certain amount of dust will enter into the cabin, even in other types of vehicles. Therefore, this phenomenon is not limited to the causes described in this document. Customers having this concern should have their vehicle repaired using the following repair procedure. NOTE: This repair procedure is an interim countermeasure. After a mass production change is implemented, the repair procedure will be updated. Attach the protectors (urethane pads, deflectors and protectors) to both sides of the designated locations according to the following steps.
SA-031-262026-05-05. Service bulletin. STRUCTURE:BODY; UNKNOWN OR OTHER. DESCRIPTION Some vehicles may require the replacement of a damaged VIN plate or vehicle certification label. To obtain a replacement VIN plate (bulkhead-mounted and visible through the lower-left area of the windshield), contact DAG (Dealer Assistance Group) using VIN Plate Request Form available on One Mazda. To obtain a replacement vehicle certification label (located on the B􀀀pillar or front door), contact your assigned DSM (District Service Manager) to place the order. If DSM contact information is not available, refer to the Dealer & Field Contact Directory.
09-009-262026-03-03. Service bulletin. STRUCTURE:BODY. Some vehicles exhibit creaking noise from the left side power liftgate (PLG) drive unit when moving (opening/closing) the power liftgate by hand and /or automatically. The noise tends to occur during moving, particularly at the start of opening or closing. As the condition progresses, it may be accompanied by functional issues such as increased operating effort, a “hard to move” feeling, or the PLG stops partway during opening or closing.
SA-003-262026-02-03. Service bulletin. ELECTRICAL SYSTEM; STRUCTURE:BODY. Customers may report that the liftgate does not open or unlatch (from closed or an ajar position). This may happen after a discharged battery or after charging a dead battery.
SA-011-25a2025-11-05. Service bulletin. STRUCTURE:BODY. Some customers will report that their fuel door (AKA, fuel filler door, fuel lid, and fuel-filler lid) was stuck closed and would not open to refuel the vehicle. Follow the repair steps below unless the conditions outlined in TSB 09-007/25 - FUEL-FILLER LID PANEL IS DEFORMED for 2019-2025 Mazda3 and 2020-2025 CX-30 are present.
SA-039/252025-09-05. Service bulletin. UNKNOWN OR OTHER; STRUCTURE:BODY. Some vehicles may experience exterior trim heat damage such (melted, separating, etc.) when parked near a glass building or Low-E windows. This may be caused by the sun's reflection. If a structure's windows create enough of a curve, the concave glass can focus the sun's rays onto a small area and acting like magnifiying glass direct the sunbeams into a hot pinpoint of light. This magnifcation of the sun's rays can cause damage to vehicle trim (see examples). Additional information and exemplar images regarding this phenomenon can be found by performing a google search.
09-031-252025-09-04. Service bulletin. STRUCTURE:BODY. While driving on gravel or dusty roads, dust accumulates at the lower inner edge of the door garnish. When the rear door is opened, the dust may be blown up and enter the cabin, adhering to the seats and the floor. This is caused by a large gap at the lower part of the boundary between the rear door and the front door, and air containing dust and/or sand is sucked up into the gap, accumulating at the lower edge of the rear door garnish while driving. To eliminate this concern, a mass production change is under study.

The summaries are NHTSA's. Each bulletin's page links NHTSA's copy of the manufacturer's document.