WenmarOpen by Wenmar Pro

Service bulletins for the 2020 Jeep Wrangler

A bulletin is a manufacturer's communication to its dealers, as NHTSA indexes it. The summary is NHTSA's. The document is the manufacturer's: read it at NHTSA. A bulletin is not a recall, and listing a model year does not mean every vehicle of it is concerned.

1020 on file from NHTSA, as of 2026-10-19.

By type

By component

By trouble code

Only bulletins with component: Backup camera are shown. Show all

Bulletins, newest first
03002242024-03-18. Service bulletin. EXTERIOR LIGHTING; BACK OVER PREVENTION. Front and Rear Axle Sensor Kit **Customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find that the following Diagnostic Trouble Code (DTC) has been set: ? C1451-11 - Service Axle Locker System** Customers may also comment on a Service Axle Locker message displayed in the Electronic Vehicle Information Center (EVIC) for this condition.
S23190000072024-01-08. Service bulletin. BACK OVER PREVENTION; STEERING:CRITICAL FASTENERS; STEERING. Squeak Noise From Dash Area When Turning The Steering Wheel.
08045232024-01-02. Service bulletin. BACK OVER PREVENTION:SOFTWARE. Radio Over The Air Updating to 34.42 Software Version ? Mobile Wi-Fi inoperative upon start up. ? Hotspot gives 9No Internet9 connection message on phone when trying to connect to a device. This bulletin provides information regarding the latest Firmware Over The Air (FOTA) update and provides the service technician an overview of the steps a customer will need to take to complete the update. The radio software will be updated from 34.4 to 34.42.
S20250000012024-01-02. Service bulletin. EXTERIOR LIGHTING; BACK OVER PREVENTION. Malfunction Indicator Lamp Illumination (MIL). Diagnostic Trouble Code (DTC) P203E ? Reductant Level Sensor 1 Circuit Intermittent-Erratic Set.
90033572024-01-02. Service bulletin. BACK OVER PREVENTION. ADAPTER, Engine Oil Filter (Pentastar V6) For all 2014MY replace the Oil Filter Adapter (OFA). For any other MY (with mileage above 30,000) review and follow instructions from STAR Online S1809000007 REV. C available on Dealer Connect. Also, consider the following: 1) Remove OFA 2) Replace only the oil inlet O-ring and gaskets (seals kit in SOL above). 3) Re-install the OFA. For 2023MY and beyond use black O-ring. For 2022MY and prior use red O-ring. Note: When replacing OFA, it may be necessary to transfer the Oil Temp/Pressure Sensor from the old OFA to the new OFA.
91001342024-01-02. Service bulletin. SERVICE BRAKES; FUEL SYSTEM, GASOLINE; BACK OVER PREVENTION. Engine When replacing a GMET4 long block from a 2021 JL or older, you will need to carry over the injector wiring harness from the original engine, and the Fuel pressure sensor should be replaced with part number: 68212572AB.
91002472023-12-18. Service bulletin. BACK OVER PREVENTION; VEHICLE SPEED CONTROL. ERG Hydraulic Tensioner Before replacing any FEAD components, please check FEAD belt layout as per the engine sales code. Customer complaint may include a noise from under the hood described as a squeal, screech, squeak, chirp or belt-related noise and/or noisy tensioner/pulley. Please refer to SOL# S2309000007.
S18080001522023-10-02. Service bulletin. VEHICLE SPEED CONTROL:ACCELERATOR PEDAL; BACK OVER PREVENTION. CEL (Check Engine Lamp) Illuminated, P057B Brake Pedal Position Sensor Performance
91001332023-07-31. Service bulletin. BACK OVER PREVENTION. ROCKER ARM ASSY - ROLLER ROCKER Case 1.- Before replacing the intake or exhaust rocker arms due to an abnormal ticking noise, please check that the INTAKE Hydraulic Lash Adjusters are not "collapsed". If a collapsed INTAKE HLA is found, replace all INTAKE HLAs on the suspect cylinder head (no need to replace rocker arms). The noise can occur at low or high RPMs, and at low or high temperatures. There are no Diagnostic Trouble Codes (DTC)s present. Case 2.- If the INTAKE camshaft or INTAKE rocker arm has excessive wear on the high lift profile (Rocker arm: slider, Camshaft: central lobe), replace the intake camshaft (1) in that cylinder head and all intake rocker arms (6).
S20250000012023-04-17. Service bulletin. BACK OVER PREVENTION; EXTERIOR LIGHTING. Malfunction Indicator Lamp Illumination (MIL). Diagnostic Trouble Code (DTC) P203E ? Reductant Level Sensor 1 Circuit Intermittent-Erratic Set.
08-038-232023-02-13. Service bulletin. BACK OVER PREVENTION:SOFTWARE. Radio Over The Air JR34.3 Updating to JR34.32.Software Version Customers may experience one or more of the following: Not be able to use Mobile Wi-Fi upon start up. Hotspot gives a no Internet connection message on phone when trying to connect to a device. This bulletin provides information regarding the latest Firmware Over The Air (FOTA) update and provides the service technician an overview of the steps a customer will need to take to complete the update. The radio software will be updated from JR34.3 to JR34.32. NOTE: National launch for this FOTA update is expected to begin February 20, 2023.
08-022-232023-02-13. Service bulletin. BACK OVER PREVENTION:SOFTWARE. Radio Over The Air Updating to 40.12 Software Version Mobile Wi-Fi inoperative upon start up. Hotspot gives 9No Internet9 connection message on phone when trying to connect to a device. This bulletin provides information regarding the latest Firmware Over The Air (FOTA) update and provides the service technician an overview of the steps a customer will need to take to complete the update. The radio software will be updated from 39.5 to 40.12.
18-003-232023-02-13. Service bulletin. ELECTRONIC STABILITY CONTROL:AUTOMATIC (ASC); SERVICE BRAKES, HYDRAULIC; ENGINE AND ENGINE COOLING; POWER TRAIN; FUEL SYSTEM, GASOLINE; PARKING BRAKE; EXTERIOR LIGHTING; ELECTRICAL SYSTEM; BACK OVER PREVENTION. Flash: Powertrain Control Module (PCM) Updates Customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find that one or more of the following Diagnostic Trouble Codes (DTCs) have been set: **P016F - Closed Loop Fuel Pressure Control At Limit - Pressure Too Low. P025C - Fuel Pump Module Control Circuit Low. P208B - Reductant Pump 1 Control Performance. P0300-00 - Multiple Cylinder Misfire (MIL Illuminated During 4WD-LO Only). P0301-00 - Cylinder 1 Misfire (MIL Illuminated During 4WD-LO Only). P0302-00 - Cylinder 2 Misfire (MIL Illuminated During 4WD-LO Only). P0303-00 - Cylinder 3 Misfire (MIL Illuminated During 4WD-LO Only). P0304-00 - Cylinder 4 Misfire (MIL Illuminated During 4WD-LO Only). P0305-00 - Cylinder 5 Misfire (MIL Illuminated During 4WD-LO Only). P0403-00 - EGR Control Circuit Open ? Disabled Fault.** P225D-00 - NOX Sensor 1/1 Performance Signal Stuck Low. P249C-00 - Excessive Time To Enter Closed Loop Reductant Injection Control. P065A - Generator System Performance. P00F4-00 - Humidity Sensor Circuit Low. P20FB-00 - Reductant Pump 2 Control Performance. P200A-00 - Intake Manifold Runner Performance Bank 1. P200B-00 - Intake Manifold Runner Performance Bank 2. P2610 - PCM Internal Engine Off Timer Performance. P0534-00 - AC Refrigerant System A Charge Loss. P04DB-00 - Crankcase Ventilation System Disconnected. P204F-00 - Reductant System Performance. P2199-00 - Intake Air Temperature Sensor 1/2 Correlation. P0087-00 - Fuel Rail Pressure Too Low (with rapid apply and release of accelerator pedal). P0306-00 - Cylinder 6 Misfire. P01CB-00 - Cylinder 1 Injection Timing Performance Over Retarded. P01CC-00 - Cylinder 1 Injection Timing Performance Over Advanced. P01CD-00 - Cylinder 2 Injection Timing Performance Over Retarded. P01CE-00 - Cylinder 2 Injection Timing Performance Over Advanced. P01CF-00 - Cylinder 3 Injection Timing Performance Over Retarded. P01D0-00 - Cylinder 3 Injection Timi
24007212023-01-17. Service bulletin. ELECTRICAL SYSTEM; BACK OVER PREVENTION:SOFTWARE. Flash: HVAC Diagnostic and System Updates This bulletin involves reprogramming the HVAC control module with the latest available software. The customer may notice one or more of the following:Intermittent change of smell or humidity level in vehicle. An intermittent blast of warm air when A/C is on. Intermittent increase of outside air through the HVAC system. In addition, the following software enhancement is also available:Improvements for customer concerns of 'cabin too warm', specifically in the mid ambient temperature range 4.5-15.5 °C (40-60 °F).
18049212023-01-17. Service bulletin. EXTERIOR LIGHTING; ELECTRICAL SYSTEM; BACK OVER PREVENTION; SERVICE BRAKES; FUEL SYSTEM, GASOLINE. Flash: Powertrain Control Module (PCM) Updates This bulletin involves reprogramming the PCM with the latest available software. Customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation, a technician may find one or more of the following DTCs have been set: P225D-00 - Nox Sensor 1/1 Performance - Signal Stuck Low. P249C-00 - Excessive Time To Enter Closed Loop Reductant Injection Control. P065A - Generator System Performance. P00F4-00 - Humidity Sensor Circuit Low. P00AF-00 -Turbocharger Boost Control Module "A" Performance. P0106-00 - Manifold Absolute Pressure Sensor Performance. P20FB-00 - Reductant Pump 2 Control Performance. P200A-00 - Intake Manifold Runner Performance - Bank 1. P200B-00 - Intake Manifold Runner Performance - Bank 2. P2610 - PCM Internal Engine Off Timer Performance. P0087-00 - Fuel Rail Pressure Too Low (with rapid apply and release of accelerator pedal). P015E-00 - Excessive Time To Enter Closed Loop Fuel Timing Control. P01CB-00 - Cylinder 1 Injection Timing Performance - Over Retarded. P01CC-00 -
S20230000112023-01-17. Service bulletin. BACK OVER PREVENTION; VISIBILITY; VEHICLE SPEED CONTROL. Wind Noise And Or Gap At Front Door Mirror Flag
S21230000292023-01-17. Service bulletin. BACK OVER PREVENTION. Squeak and or Chirp Noise From Lift Gate Glass
08-003-22 REV. A2023-01-17. Service bulletin. STEERING; EQUIPMENT:ELECTRICAL:INFOTAINMENT; BACK OVER PREVENTION. UAQ and UCQ Radio Enhancements Customers may experience one or more of the following: ? **Wi-Fi hotspot connection failure. ? Speaker popping, crackle noise during Voice Recognition (VR) response and navigation guidance. ? Mobile Station Integrated Services Digital Network (MSISDN) missing from radio, no connected services working.** ? Intermittent, black radio display screen (Rear View Camera (RVC) not affected). ? Intermittent, radio freezes (RVC not affected). ? Wireless connectivity pairing and/or connection issues. ? Lost radio presets. ? Radio channels change by itself. ? SXMT icon inoperative. ? SXMT favorite song not displaying/playing. ? Incorrect navigation address/location/directions. ? Backup camera has black display screen or only displays Check Entire Surroundings with black screen (occurs when vehicle is shifted immediately to reverse upon key-on before RVC signal is received, recoverable with key cycle) . ? High pitch chime noise. ? Contact list not loading. ? Device not supported message. ? Remote app inoperative. ? Travel-Link fuel price incorrect. ? Backup camera gridlines missing. ? Unable to adjust volume. In addition, the following enhancement are included in this update: ? Enables map updates. ? Heavy Duty (HD) Truck USB HUB improvements. ? HD Truck heated steering wheel improvements This bulletin involves inspecting and if required, updating the radio software level to 40.1. Depending on the radio?s current software level the radio may need a one or two USB update.
S20080001122023-01-09. Service bulletin. BACK OVER PREVENTION:DISPLAY FUNCTION; STRUCTURE:INTERIOR PANELS:DASHBOARD. MIL Lamp On Setting DTC?s P0441, P0456, P0457, P0440
S20250000062023-01-09. Service bulletin. BACK OVER PREVENTION; EXTERIOR LIGHTING. Malfunction Indicator Lamp (MIL) Illumination. Diagnostic Trouble Code (DTC) P206D ? Reductant Quality Sensor Circuit High Set.
18049222023-01-09. Service bulletin. BACK OVER PREVENTION; EXTERIOR LIGHTING; ELECTRICAL SYSTEM. Flash: Powertrain Control Module (PCM) Updates This bulletin involves reprogramming the PCM with the latest available software. Customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find the following (DTC): P0441- EVAP Purge System Performance. The customer may comment on one or more of the following: Abnormal Engine noise heard periodically. This noise is caused by Variable Valve Timing (VVT) cleaning cycle. A misfire condition with no Malfunction Indicator Lamp (MIL) illuminationor Diagnostic Trouble Codes (DTCs) set. In addition, the following software enhancements are available: Updates to include misfire DTCs.
S22230000292023-01-09. Service bulletin. BACK OVER PREVENTION. Rattle Noise From Door
91000102022-10-31. Service bulletin. POWER TRAIN:AXLE ASSEMBLY; WHEELS; BACK OVER PREVENTION. Axle Assembly A parts kit (SENSOR KIT, Axle: 68544629A$) is available to repair the Axle Locker Sensor on JL/JT equipped with the M210 and M220 Tru-Lok axles (DSE). This parts kit must be used when only the Axle Locker Sensor fails. Do not replace the axle for sensor failure.
S20250000012022-10-17. Service bulletin. EXTERIOR LIGHTING; BACK OVER PREVENTION. (Rev. B) Malfunction Indicator Lamp Illumination (MIL). Diagnostic Trouble Code (DTC) P203E ? Reductant Level Sensor 1 Circuit Intermittent-Erratic Set.
18049212022-10-17. Service bulletin. SERVICE BRAKES, HYDRAULIC; ELECTRICAL SYSTEM:SOFTWARE; FUEL SYSTEM, GASOLINE; EXTERIOR LIGHTING; ELECTRICAL SYSTEM; BACK OVER PREVENTION. Flash: Powertrain Control Module (PCM) Updates This bulletin involves reprogramming the PCM with the latest available software. Customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation, a technician may find one or more of the following DTCs have been set: P225D-00 - Nox Sensor 1/1 Performance - Signal Stuck Low. P249C-00 - Excessive Time To Enter Closed Loop Reductant Injection Control. P065A - Generator System Performance. P00F4-00 - Humidity Sensor Circuit Low. P00AF-00 -Turbocharger Boost Control Module "A" Performance. P0106-00 - Manifold Absolute Pressure Sensor Performance. P20FB-00 - Reductant Pump 2 Control Performance. P200A-00 - Intake Manifold Runner Performance - Bank 1. P200B-00 - Intake Manifold Runner Performance - Bank 2. P2610 - PCM Internal Engine Off Timer Performance. P0087-00 - Fuel Rail Pressure Too Low (with rapid apply and release of accelerator pedal). P015E-00 - Excessive Time To Enter Closed Loop Fuel Timing Control. P01CB-00 - Cylinder 1 Injection Timing Performance - Over Retarded. P01CC-00 - Cylinder 1 Injection Timing Performance - Over Advanced. P01CD-00 - Cylinder 2 Injection Timing Performance - Over Retarded. P01CE-00 - Cylinder 2 Injection Timing Performance - Over Advanced. P01CF-00 - Cylinder 3 Injection Timing Performance - Over Retarded. P01D0-00 - Cylinder 3 Injection Timing Performance - Over Advanced. P01DL-00 - Cylinder 4 Injection Timing Performance - Over Retarded. P01D2-00 - Cylinder 4 Injection Timing Performance - Over Advanced. P01D3-00 - Cylinder 5 Injection Timing Performance - Over Retarded. P01D4-00 - Cylinder 5 Injection Timing Performance - Over Advanced. P01D5-00 - Cylinder 6 Injection Timing Performance - Over Retarded. P01D6-00 - Cylinder 6 Injection Timing Performance - Over Advanced. P0534-00 - A/C Refrigerant System "A" Charge Loss. P204F-00 - Reductant System Performance. P2199-00 - Intake Air Temperature Sensor 1/2 Correlation.

The summaries are NHTSA's. Each bulletin's page links NHTSA's copy of the manufacturer's document.