WenmarOpen by Wenmar Pro

Service bulletins for the 2025 Jeep Grand Wagoneer

A bulletin is a manufacturer's communication to its dealers, as NHTSA indexes it. The summary is NHTSA's. The document is the manufacturer's: read it at NHTSA. A bulletin is not a recall, and listing a model year does not mean every vehicle of it is concerned.

344 on file from NHTSA, as of 2026-10-19.

By type

By component

By trouble code

Only bulletins with component: Steering are shown. Show all

Bulletins, newest first
S2523000053 REV.C2026-08-13. Service bulletin. STEERING. Service Electric Power Steering (EPS) Message On Instrument Cluster. Rev B.
S2523000053 REV.B2026-07-23. Service bulletin. ELECTRICAL SYSTEM; STEERING. Service Electric Power Steering (EPS) Message On Instrument Cluster. Rev B.
9100532 REV12026-05-20. Service bulletin. ELECTRICAL SYSTEM; STEERING. Before replacing the steering column control module (SCCM) due to wipers inop, wipers not turning off, wipers not returning to position, heated steering wheel not working and/or steering controls inop, Electronic Stability Control (ESC) light on, please follow these steps: 1.- Review if there is any active DTC. Refer to service library procedure and follow diagnosis steps. 2.- If failure still present, make sure all the switches', horn's, heated steering wheel, airbag's harness are properly connected and there is no corrosion or pinching, disconnect the switches & reconnect them, and reverify the issue. 3.- Verify if failure is still present, review if there is lack of communication between SCCM and BCM. For example, activate turn signals or wipers. 4.- Read at the BCM diagnosis session if BCM is receiving information from SCCM. Through diagnosis review if activation from horn, wipers or turn signal is requested and are working. 5.- Disconnect the SCCM fuse for around 30s,and repeat the previous steps to see if failure still present. 6.- Do a hard reset to BCM and evaluate if any DTC is set. Retest if failure still present. Review the active DTCs. 7.- Before replacing the SCCM disconnect it and reconnect it again. Note: Wipers position is not controlled by SCCM, verify motor wiper status if issue continues. If request from SCCM is sent to BCM, then verify if the communication to wipers is not working properly. If there are no DTC's active, physical defects, steering controls inop, wipers inop, heated steering wheel inop, then SCCM does not need to be replaced. Note: WL / WS SCCMs do not contain a Steering Angle Sensor (SAS) The Steering Angle is computed within the Electronic Power Steering (EPS) module. See Electronic Power Steering (EPS) module for diagnosis and repair procedures.
S2219000004 REV.A2026-03-25. Service bulletin. STEERING. Service Electric Power Steering Message On Cluster. C0051-54 Steering Wheel Position Sensor Calibration, C0051-64 Steering Angle Set.
1089422025-12-11. Service bulletin. STEERING. MODULE - STEERING CONTROL
1089412025-12-11. Service bulletin. STEERING. MODULE - STEERING CONTROL
1056462025-10-15. Service bulletin. STEERING. MODULE - STEERING CONTROL & COLUMN
S2523000053 REV.A2025-07-31. Service bulletin. ELECTRICAL SYSTEM; STEERING. Service Electric Power Steering (EPS) Message On Instrument Cluster.
S25190000062025-07-23. Service bulletin. ELECTRICAL SYSTEM; STEERING. Steering Repair Information Involving Toe Angle. Tie Rod And Or Electric Power Steering (EPS) Units.
S25190000052025-07-17. Service bulletin. STEERING; ELECTRICAL SYSTEM. Service Electric Power Steering Message On Cluster.
S2219000005 REV.D2025-07-09. Service bulletin. STEERING; ELECTRICAL SYSTEM. Check Engine Lamp On. Warning Messages in the Cluster. U0131 Lost Communication with Power Steering Control Module Set.
08-185-252025-06-18. Service bulletin. STEERING. "Loss Of Power Steering Assist Customers must experience a Malfunction Indicator Lamp (MIL) illumination and the vehicle must exhibit/set one or more of the following Diagnostic Trouble Codes (DTCs) as active: ● C1593-00 - Steering Torque Sensor Circuit. ● C0051-64 - Steering Angle Sensor (EPS) - Signal Plausibility Failure. Customers may experience one or more of the following: ● ""EPS"" indicator is illuminated on the Instrument Panel Cluster (IPC). ● Partial or full loss of power steering assist. ● Once the DTC is set, the reduction or loss of assist will remain for the remainder of the key cycle This bulletin involves involved inspecting the Electronic Power Steering (EPS) wire harness connector, cleaning the connector or possibly replacing the electric rack and pinion gea"
S25230000542025-06-11. Service bulletin. LANE DEPARTURE: ASSIST; STEERING; LANE DEPARTURE: WARNING. Intermittent Vibration Buzz Squeak Rattle (BSR) Shaking Felt In Steering Wheel.
S25230000532025-06-11. Service bulletin. ELECTRICAL SYSTEM; STEERING. Service Electric Power Steering (EPS) Message On Instrument Cluster.
91005962025-06-10. Service bulletin. STEERING. "Gear Assy - Steering Rack 1) If below DTCs are observed, please refer to 08-095-25 REV. B (For MY24) and 08-094-25 REV. A (For MY25) U0420-00 - Invalid Data Received from Power Steering Control Module. (Set by CADM2) C2217-00 - Electric Power Steering Module Internal. C221F-00 - ECU Not Initialized. C1592-00 - Electronic Power Steering Motor Circuit. C1593-00 - Steering Torque Sensor Circuit. 2) IF C2217 DTC is observed to be active, please make sure that both connectors on EPS are receiving voltage ranging between 10V-16V"
08-094-25 REV. A2025-05-30. Service bulletin. STEERING; ELECTRICAL SYSTEM. "Flash: Electric Power Steering (EPS) Module Updates Customers must experience a Malfunction Indicator Lamp (MIL) illumination and the vehicle must exhibit/set one or more of the following Diagnostic Trouble Codes (DTCs): ● **U0420-00 - Invalid Data Received From Power Steering Control Module.** ● C2217-00 - Electric Power Steering Module Internal. ● C221F-00 - ECU Not Initialized. ● C1592-00 - Electronic Power Steering Motor Circuit. ● C1593-00 - Steering Torque Sensor Circuit. Customers may also experience the following: ● Loss of steering assist and/or a steering warning light on in the Instrument Panel Cluster (IPC). NOTE: **If the power steering assist is lost, it will remain out until the next key cycle. This bulletin involves updating the EPS module with the latest available software. "
08-094-252025-04-08. Service bulletin. ELECTRICAL SYSTEM; STEERING. "Flash: Electronic Power Steering (EPS) Module Updates Customers must experience a Malfunction Indicator Lamp (MIL) illumination and the vehicle must exhibit/set one or more of the following Diagnostic Trouble Codes (DTCs): ● C2217-00 - Electric Power Steering Module Internal. ● C221F-00 - ECU Not Initialized. ● C1592-00 - Electronic Power Steering Motor Circuit. ● C1593-00 - Steering Torque Sensor Circuit. Customers may also experience the following: ● Loss of steering assist and/or a steering warning light on in the Instrument Panel Cluster (IPC ) This bulletin involves updating the EPS module with the latest available software"
91005322025-03-26. Service bulletin. STEERING; ELECTRICAL SYSTEM. "MODULE Steering Control Before replacing the steering column control module (SCCM) due to wipers inop, wipers not turning off, wipers not returning to position, heated steering wheel not working and/or steering controls inop, please follow these steps: 1.- Review if there is any active DTC. Refer to service library procedure and follow diagnosis steps. 2.- If failure still present, make sure all the switches', horn's, heated steering wheel, airbag's harness are properly connected and there is no corrosion or pinching, disconnect the switches & reconnect them, and reverify the issue. 3.- Verify if failure is still present, review if there is lack of communication between SCCM and BCM. For example, activate turn signals or wipers. 4.- Read at the BCM diagnosis session if BCM is receiving information from SCCM. Through diagnosis review if activation from horn, wipers or turn signal is requested and are working. 5.- Disconnect the SCCM fuse for around 30s,and repeat the previous steps to see if failure still present. 6.- Do a hard reset to BCM and evaluate if any DTC is set. Retest if failure still present. Review the active DTCs. 7.- Before replacing the SCCM disconnect it and reconnect it again. Note: Wipers position is not controlled by SCCM, verify motor wiper status if issue continues. If request from SCCM is sent to BCM, then verify if the communication to wipers is not working properly. If there are no DTC's active, physical defects, steering controls inop, wipers inop, heated steering wheel inop, then SCCM does not need to be replaced."
S2219000005 REV.C2025-02-14. Service bulletin. ENGINE; ELECTRICAL SYSTEM; STEERING. Check Engine Lamp On. Warning Messages In The Cluster. U0131 Lost Communication With Power Steering Control Module Set.
S2219000007 REV.A2024-10-09. Service bulletin. STEERING. Service Electric Power Steering (EPS) Message Displayed on Cluster Upon Start Up
S2319000005 REV.A2024-10-03. Service bulletin. STEERING. Customer Complaint Of Loss Of Power Steering Assist.

The summaries are NHTSA's. Each bulletin's page links NHTSA's copy of the manufacturer's document.