WenmarOpen by Wenmar Pro

Service bulletins for the 2025 Jeep Grand Cherokee

A bulletin is a manufacturer's communication to its dealers, as NHTSA indexes it. The summary is NHTSA's. The document is the manufacturer's: read it at NHTSA. A bulletin is not a recall, and listing a model year does not mean every vehicle of it is concerned.

423 on file from NHTSA, as of 2026-10-19.

By type

By component

By trouble code

Bulletins, newest first
91005492025-04-16. Service bulletin. ELECTRICAL SYSTEM. "Keyfob WL/WS/LB Key fobs unable to be programmed at dealers. Please check current stock and verify a green check mark on part label. If not present send part back to Mopar under RMA 8925-792 and replace with clean stock from Mopar. Some vehicles may exhibit DTC B1A0A-00 that has set erroneously and with no associated owner complaints. It is not recommended to replace any parts for this concern, all service parts will perform the same. Engineering is aware of a software issue that may set this false DTC for FOB 3 Performance when there may not even be a FOB 3 programmed to the vehicle. A software update is expected to be released within the 1st quarter of 2025 to correct this concern."
08-111-252025-04-15. Service bulletin. ELECTRICAL SYSTEM; SEATS. "Right Front Heated Seat Inoperative Customers must experience a Malfunction Indicator Lamp (MIL) illumination and the vehicle must exhibit/set the following Diagnostic Trouble Code (DTC): ● B1E9A - Front Right Heater Control 1 – Circuit Open. Customers may experience the following: ● Right front heated seat will not activate or will shut off after a few seconds. This bulletin involves inspecting and possibly repairing the heated seat harness connector"
1045582025-04-11. Warranty extension. UNKNOWN OR OTHER. FCA Caribbean Warranty Newsletter – Volume 11, Issue 4
S25080000282025-04-10. Service bulletin. ELECTRICAL SYSTEM. Cluster Off-Road Pages Have A Delay In Updating Graphics And Data
1045572025-04-10. Warranty extension. UNKNOWN OR OTHER. Warranty Newsletter – Volume 11, Issue 4
91004752025-04-10. Service bulletin. ELECTRICAL SYSTEM. "Key Fob Some vehicles may exhibit DTC B1A0A-00 that has set erroneously and with no associated owner complaints. It is not recommended to replace any parts for this concern, all service parts will perform the same. Engineering is aware of a software issue that may set this false DTC for FOB 3 Performance when there may not even be a FOB 3 programmed to the vehicle. A software update is expected to be released within the 1st quarter of 2025 to correct this concern."
S25230000232025-04-07. Service bulletin. ELECTRICAL SYSTEM. Trailer Tow Lights Inoperative. Diagnostic Trouble Codes (DTCs) B166E-13 B17AD-13 May Be Set.
S25090000042025-04-03. Service bulletin. ENGINE. Misfire DTCs, Rough Idle, Valvetrain Noise
S2523000010 REV.A2025-04-03. Service bulletin. STRUCTURE:BODY. Exterior Rear View Mirror Stained And Will Not Clean.
S2508000014 REV.B2025-04-03. Service bulletin. ELECTRICAL SYSTEM. Security Gateway (SGW) Module is Setting Diagnostic Trouble Code (DTC) U3033-00 Control Module Security Certificate Missing or Invalid
1039532025-04-02. Service bulletin. UNKNOWN OR OTHER. VALVE - OIL CONTROL
S2509000001 REV.A2025-04-01. Service bulletin. ENGINE. Engine Rattle Noise
91005312025-04-01. Service bulletin. SEATS. "2nd row seat frame 2nd Row Seat is hard to put back In position after moving it forward to access the 3rd row seat. Add grease as noted in the SOL publication S2423000041"
91005322025-03-26. Service bulletin. STEERING; ELECTRICAL SYSTEM. "MODULE Steering Control Before replacing the steering column control module (SCCM) due to wipers inop, wipers not turning off, wipers not returning to position, heated steering wheel not working and/or steering controls inop, please follow these steps: 1.- Review if there is any active DTC. Refer to service library procedure and follow diagnosis steps. 2.- If failure still present, make sure all the switches', horn's, heated steering wheel, airbag's harness are properly connected and there is no corrosion or pinching, disconnect the switches & reconnect them, and reverify the issue. 3.- Verify if failure is still present, review if there is lack of communication between SCCM and BCM. For example, activate turn signals or wipers. 4.- Read at the BCM diagnosis session if BCM is receiving information from SCCM. Through diagnosis review if activation from horn, wipers or turn signal is requested and are working. 5.- Disconnect the SCCM fuse for around 30s,and repeat the previous steps to see if failure still present. 6.- Do a hard reset to BCM and evaluate if any DTC is set. Retest if failure still present. Review the active DTCs. 7.- Before replacing the SCCM disconnect it and reconnect it again. Note: Wipers position is not controlled by SCCM, verify motor wiper status if issue continues. If request from SCCM is sent to BCM, then verify if the communication to wipers is not working properly. If there are no DTC's active, physical defects, steering controls inop, wipers inop, heated steering wheel inop, then SCCM does not need to be replaced."
91005222025-03-21. Service bulletin. ENGINE. "Ebooster When replacing the brake ebooster under warranty. Please return all associated parts which includes the snap rings so that the parts can be review by engineering."
91004712025-03-19. Service bulletin. UNKNOWN OR OTHER. "CANISTER Vapor -If an issue is detected with the Evaporative System Integrity Module (ESIM) Detector and not the Vapor Canister, only replace the ESIM Detector. -Before replacing the Vapor Canister due to Hard to Fill condition, replicate the condition at the Gas Station. If the condition is replicated, then check: 1) for kinked or pinched Clean Air Hose between the ESIM and the EVAP Air Filter; 2) for plugged EVAP Air Filter; 3) for kinked or pinched Vapor Hose between the Fuel Tank and the Vapor Canister. If the EVAP Filter is restricted, the replace the Filter. -Check if the Vapor Canister is flooded with fuel or the Recirculation Line has fuel. If fuel is found in the Vapor Canister or the Recirculation Line, then drop the Fuel Tank, remove the FDM Lock Ring to check if the internal Vapor Line is properly connected to the FDM Port. If the Vapor Line is not connected, then drain the fuel from the internal Vapor Line and properly connect to the FDM. Replace the Vapor Canister and the ESIM."
S25080000202025-03-19. Service bulletin. ELECTRICAL SYSTEM. Odometer Blinking, Security Gateway (SGW) Diagnostic Trouble Codes (DTCs) Diagnostics
S2508000008 REV.C2025-03-17. Service bulletin. ELECTRICAL SYSTEM. Battery Drained, Ignition Off Draw (IOD), Cluster Display Goes Off and On, and/or Door Lock Indicator Lamps Stay Illuminated
S2508000014 REV.A2025-03-13. Service bulletin. ELECTRICAL SYSTEM. Security Gateway (SGW) Module is Setting Diagnostic Trouble Code (DTC) U3033-00 Control Module Security Certificate Missing or Invalid
91005022025-03-07. Service bulletin. STRUCTURE:BODY. LOWER ACTIVE GRILL SHUTTER If the upper or lower AGS seems to be inop please make sure you CLEAR the DTCs BEFORE swapping the old AGS for a new one, and test if the error code returns. Very often the wiring harness presents corrosion, so make sure to check it for any damage BEFORE swapping the AGS. Corrosion in the harness disrupts communication with the AGS, which sets up the DTCs for AGS performance and lights the CEL. If the AGS is inop and it will be replaced and sent back to Stellantis also send back the wiring harness with it. Make sure to fully perform the PRE-DIAGNOSTIC TROUBLESHOOTING PROCEDURE as indicated in the service library.
S258A0000092025-03-07. Service bulletin. ELECTRICAL SYSTEM. Apple CarPlay Does Not Complete The First Initial Wireless Connection.
S2508000008 REV.B2025-03-07. Service bulletin. ELECTRICAL SYSTEM. Battery Drained, Ignition Off Draw (IOD), Cluster Display Goes Off and On, and/or Door Lock Indicator Lamps Stay Illuminated
S25090000022025-03-07. Service bulletin. ENGINE. Engine Noise
S258A0000072025-03-07. Service bulletin. ELECTRICAL SYSTEM. Radio Display Screen Flicker
9100446 Rev 32025-03-05. Service bulletin. SUSPENSION. "Frt Stabilizer assembly(smartbar) BSR from the front end due to Smartbar (disconnecting front sway bar). Root cause was identified as anti-rotation bracket (connects the actuator to the stabar) coming loose due to inadequate clamp load at the joint and weld (holds the bolt shaft and bracket flange) was poorly designed. If any vehicle causes BSR because of this Bracket failure (loose joint/ bracket bends) DO NOT replace whole stabar assembly, instead replace with the service kit (PN#68730602AA). Dealer must need to order the parts from part ordering system for this claim. This kit contains 1 bracket (PN 68730603AA), 3 M10 Nut (PN 68730605AA), 2 M8X1.5 Bolt (PN 68730606AA) and 2 M10X1.5 bolt (PN 06513427AA). 1 M10 Bolt (PN 68730607AA). This kit will also contain a new torque instruction for the bolt which holds the clamp bracket to this failed anti-rotation bracket. DO NOT apply the old torque (45+/5Nm Direct torque). The new torque is Angle controlled torque monitor (20Nm Snug torque, 110 deg Angle, monitor torque within 40-70Nm). Please use Service Library for your reference."

The summaries are NHTSA's. Each bulletin's page links NHTSA's copy of the manufacturer's document.