WenmarOpen by Wenmar Pro

Service bulletins for the 2015 Jeep Grand Cherokee

A bulletin is a manufacturer's communication to its dealers, as NHTSA indexes it. The summary is NHTSA's. The document is the manufacturer's: read it at NHTSA. A bulletin is not a recall, and listing a model year does not mean every vehicle of it is concerned.

513 on file from NHTSA, as of 2026-10-19.

About P2299 on the 2015 Jeep Grand Cherokee: what the code means, and the bulletins and recalls about the same components.

By type

By component

By trouble code

Only bulletins with trouble code: P2299 are shown. Show all

Bulletins, newest first
90034132022-09-15. Service bulletin. VEHICLE SPEED CONTROL:ACCELERATOR PEDAL. Accelerator Pedal Before replacing accelerator pedal, be sure to follow fault code diagnostic procedures in service manual. Make sure to check wiring and connectors. P2122 and P2127 will set if accelerator pedal connector is disconnected during diagnosis. Make sure codes are active before replacing pedal. DTC P2299 is usually caused by a two footed driver and accelerator pedal should not be replaced for this fault.
18-047-15 REV. A2022-08-08. Service bulletin. EXTERIOR LIGHTING; SERVICE BRAKES, HYDRAULIC; FUEL SYSTEM, DIESEL; BACK OVER PREVENTION; ELECTRICAL SYSTEM; FUEL SYSTEM, GASOLINE. Flash: 3.0L Powertrain Diagnostic And System Enhancements This bulletin involves reprogramming the Powertrain Control Module (PCM) with the latest available software. A small number of customers may experience a Malfunction Indicator Lamp (MIL) Illumination. Upon further investigation, a technician may find one or more of the following Diagnostic Trouble Codes (DTCs) stored in the PCM memory. ? P204F-00 - Reductant System Performance ? P20E9-00 - Reductant Pressure Too High ? P249C-00 - Excessive Time To Enter Closed Loop Reductant Injection Control ? P2002-00 - Diesel Particulate Filter Efficiency Below Threshold ? P20C2-00 - Reductant Heater 3 Control Circuit Performance ? P2299-00 - Brake Pedal Position/Accelerator Pedal Position Incompatible ? P208B-00 - Reductant Pump 1 Control Performance ? P1288-00 - NOX Sensor 1/2 Zero Offset Too High
18-047-15 REV. A2022-07-25. Service bulletin. EQUIPMENT; POWER TRAIN:AUTOMATIC TRANSMISSION; BACK OVER PREVENTION; ELECTRICAL SYSTEM. Flash: 3.0L Powertrain Diagnostic And System Enhancements This bulletin involves reprogramming the Powertrain Control Module (PCM) with the latest available software. A small number of customers may experience a Malfunction Indicator Lamp (MIL) Illumination. Upon further investigation, a technician may find one or more of the following Diagnostic Trouble Codes (DTCs) stored in the PCM memory. ? P204F-00 - Reductant System Performance ? P20E9-00 - Reductant Pressure Too High ? P249C-00 - Excessive Time To Enter Closed Loop Reductant Injection Control ? P2002-00 - Diesel Particulate Filter Efficiency Below Threshold ? P20C2-00 - Reductant Heater 3 Control Circuit Performance ? P2299-00 - Brake Pedal Position/Accelerator Pedal Position Incompatible ? P208B-00 - Reductant Pump 1 Control Performance ? P1288-00 - NOX Sensor 1/2 Zero Offset Too High
53034160A2019-05-20. Service bulletin. VEHICLE SPEED CONTROL; VEHICLE SPEED CONTROL:ACCELERATOR PEDAL. Part Description: Accelerator Pedal Issue Description: Vehicle has accelerator pedal fault code. Before replacing accelerator pedal, be sure to follow fault code diagnostic procedures in service manual. Make sure to check wiring and connectors. DTC P2299 is usually caused by a two footed driver and accelerator pedal should not be replaced for this fault.
18-095-152019-05-20. Service bulletin. ELECTRICAL SYSTEM:SOFTWARE; POWER TRAIN; FUEL SYSTEM, OTHER. Flash: 3.0L Powertrain Diagnostic And System Enhancements This bulletin involves reprogramming Powertrain Control Module (PCM) with latest available software. It also involves cleaning or replacement of Exhaust Gas Temperature (EGT) Sensor 1/2 and/or Catalyst Temperature Sensor if necessary depending on Diagnostic Trouble Codes (DTCs) that may have set. A small number of customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation a technician may find one or more of the following Diagnostic Trouble Codes (DTCs) set in PCM memory: ? P1296-00 - EGR Slow Response - Increasing Flow. ? P249C-00 - Excessive Time To Enter Closed Loop Reductant Injection Timing Control. ? P20C2-00 - Reductant Heater 3 Control Circuit Performance. ? P1297-00 - EGR Slow Response - Decreasing Flow. ? P0420-00 - Catalyst Efficiency (Bank 1). ? P2237-00 - O2 Sensor 1/1 Pump Cell Current Circuit Open. ? P24D1-00 - Particulate Matter Sensor Regeneration Incomplete. ? U0422-00 - Implausible Data Received From Body Control Module. ? P1E0C-00 - Empty Fuel Tank. ? P2463-00 - Diesel Particulate Filter - Soot Accumulation. ? P24A4-00 - Particulate Filter Restriction - Soot Accumulation Too High. ? P2299-00 - Brake Pedal Position/Accelerator Pedal Position Incompatible. ? P208B-00 - Redundant Pump 1 Control Performance. ? P1288-00 - NOX Sensor 1/2 Zero Offset Too High. ? P2002-00 - Diesel Particulate Filter Efficiency Below Threshold. ? P204F - Reductant System Performance. ? P241D-00 - SCR Inducement - Forced Engine Shutdown. ? P20E9 - Reductant Pressure Too High. Upon further investigation a technician may find following Diagnostic Trouble Code (DTC) set in TCM memory: ? U1424-00 - Implausible Engine Torque Signal Received. The following enhancements are also included in this software update. ? DTC P0171-00 System Too Lean (Bank 1) has now changed to P026C-00 Fuel Injection Quantity Lower Than Expected. • DTC P0172-00 System Too Rich
18-047-15 REV-A2018-12-17. Service bulletin. ELECTRICAL SYSTEM; SERVICE BRAKES, HYDRAULIC; ENGINE; POWER TRAIN:AUTOMATIC TRANSMISSION:CONTROL MODULE (TCM/PCM/TECM); FUEL SYSTEM, GASOLINE. Flash: 3.0L Powertrain Diagnostic And System Enhancements This bulletin involves reprogramming the Powertrain Control Module (PCM) with the latest available software. A small number of customers may experience a Malfunction Indicator Lamp (MIL) Illumination. Upon further investigation, a technician may find one or more of the following Diagnostic Trouble Codes (DTCs) stored in the PCM memory. ? P204F-00 - Reductant System Performance ? P20E9-00 - Reductant Pressure Too High ? P249C-00 - Excessive Time To Enter Closed Loop Reductant Injection Control ? P2002-00 - Diesel Particulate Filter Efficiency Below Threshold ? P20C2-00 - Reductant Heater 3 Control Circuit Performance ? P2299-00 - Brake Pedal Position/Accelerator Pedal Position Incompatible ? P208B-00 - Reductant Pump 1 Control Performance ? P1288-00 - NOX Sensor 1/2 Zero Offset Too High
18-022-15 REVA2018-12-03. Service bulletin. POWER TRAIN:AUTOMATIC TRANSMISSION:CONTROL MODULE (TCM/PCM/TECM). Flash: 3.0L Powertrain Diagnostic And System Enhancements This bulletin involves reprogramming the Powertrain Control Module (PCM) with the latest available software. A small number of customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation a technician may find one of more of the following Diagnostic Trouble Codes (DTCs) set in the PCM memory. ? P2299-00 - Brake Pedal Position/Accelerator Pedal Position Incompatible. ? P208B-00 - Redundant Pump 1 Control Performance. ? P1288-00 - NOX Sensor 1/2 Zero Offset Too High. ? P249C-00 - Excessive Time To Enter Closed Loop Reductant Injection Timing Control. ? P2002-00 - Diesel Particulate Filter Efficiency Below Threshold. ? P20C2 - Reductant Heater 3 Control Circuit Performance. ? P204F - Reductant System Performance. ? P20E9 - Reductant Pressure Too High.
18-047-152018-11-26. Service bulletin. POWER TRAIN:AUTOMATIC TRANSMISSION:CONTROL MODULE (TCM/PCM/TECM). Flash: 3.0L Powertrain Diagnostic And System Enhancements This bulletin involves reprogramming the Powertrain Control Module (PCM) with the latest available software. A small number of customers may experience a Malfunction Indicator Lamp (MIL) Illumination. Upon further investigation, a technician may find one or more of the following Diagnostic Trouble Codes (DTCs) stored in the PCM memory. ? P204F-00 - Reductant System Performance ? P20E9-00 - Reductant Pressure Too High ? P249C-00 - Excessive Time To Enter Closed Loop Reductant Injection Control ? P2002-00 - Diesel Particulate Filter Efficiency Below Threshold ? P20C2-00 - Reductant Heater 3 Control Circuit Performance ? P2299-00 - Brake Pedal Position/Accelerator Pedal Position Incompatible ? P208B-00 - Reductant Pump 1 Control Performance ? P1288-00 - NOX Sensor 1/2 Zero Offset Too High
18-022-15 REV-B2018-11-19. Service bulletin. EQUIPMENT; ELECTRICAL SYSTEM; VEHICLE SPEED CONTROL:ACCELERATOR PEDAL; SERVICE BRAKES, HYDRAULIC:PEDALS AND LINKAGES. Flash: 3.0L Powertrain Diagnostic And System Enhancements This bulletin involves reprogramming the Powertrain Control Module (PCM) with the latest available software. A small number of customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation a technician may find one of more of the following Diagnostic Trouble Codes (DTCs) set in the PCM memory. ? P2299-00 - Brake Pedal Position/Accelerator Pedal Position Incompatible. ? P208B-00 - Redundant Pump 1 Control Performance. ? P1288-00 - NOX Sensor 1/2 Zero Offset Too High. ? P249C-00 - Excessive Time To Enter Closed Loop Reductant Injection Timing Control. ? P2002-00 - Diesel Particulate Filter Efficiency Below Threshold. ? P20C2 - Reductant Heater 3 Control Circuit Performance. ? P204F - Reductant System Performance. ? P20E9 - Reductant Pressure Too High.
90034132018-06-04. Service bulletin. VEHICLE SPEED CONTROL:ACCELERATOR PEDAL. Accelerator Pedal Before replacing accelerator pedal, be sure to follow fault code diagnostic procedures in service manual. Make sure to check wiring and connectors. P2122 and P2127 will set if accelerator pedal connector is disconnected during diagnosis. Make sure codes are active before replacing pedal. DTC P2299 is usually caused by a two footed driver and accelerator pedal should not be replaced for this fault.
18-098-162017-11-03. Service bulletin. POWER TRAIN; FUEL SYSTEM, GASOLINE; ELECTRICAL SYSTEM. Flash: Powertrain Diagnostic And System Enhancements This bulletin involves reprogramming the PCM with the latest available software. Customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find that the following Diagnostic Trouble Codes (DTCs) have been set: · **P1115 - General Temperature Rationality. · P0441 - EVAP Purge System Performance. · P0456 - EVAP System Small Leak. · P030X - Cylinder x Misfire Detection. · P0335 - Crankshaft Position Sensor Circuit. · P0122 - Throttle Position Sensor 1 Circuit Low. · P0123 - Throttle Position Sensor 1 Circuit High. · P0222 - Throttle Position Sensor 2 Circuit Low. · P0223 - Throttle Position Sensor 2 Circuit High. · P2299 - Brake Pedal Position/Accelerator Pedal Position Incompatible. · P2172 - High Airflow/Vacuum Leak Detected (Instantaneous Accumulation). · P2610 - PCM Internal Engine Off Timer Performance.** · P0300 - Multiple Cylinder Misfire. · P2096 - Downstream Fuel Trim System 1 Lean. · P2097 - Downstream Fuel Trim System 1 Rich. · P2098 - Downstream Fuel Trim System 2 Lean. · P2099 - Downstream Fuel Trim System 2 Rich. · P0513 - Invalid Skim Key - May set when pressing the remote start button on the Frequency Operated Button/Integrated Key (FOBIK) and Keyless Ignition Node (KIN) at the same time. Customers may also experience one or more of the following conditions: · Unable to obtain top vehicle speed during aggressive Wide Open Throttle (WOT) operation due to false spark knock/detonation detection. · Less then desired engine performance on cold start.

The summaries are NHTSA's. Each bulletin's page links NHTSA's copy of the manufacturer's document.