P05F8 on the 2014 Jeep Grand Cherokee
The bulletins listed name this code in NHTSA's summary, or are about the same components. A bulletin or a recall listed here may apply to the model year. None of it is a diagnosis.
Nobody has written a description of this code yet.
| 1801814REVE | 2022-09-26. Service bulletin. Flash: 3.0 L MIL Illumination Diagnostic and System Improvements This bulletin involves reprogramming the Powertrain Control Module (PCM) with the latest available software. A small number of customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the Technician may find one or more of the following Diagnostic P0087-00 - Fuel Rail Pressure Too Low. P20EE-00 - SCR NOX Catalyst Efficiency Below Threshold Bank 1. P0171-00 - System Too Lean (Bank 1). P0172-00 - System Too Rich (Bank 1). P225C-00 - NOX Sensor Performance - Signal Stuck High Bank 1 Sensor 1. P225D-00 - NOX Sensor 1/1 Performance - Signal Stuck Low. P1288-00 - NOX Sensor 1/2 Zero Offset Too High. P1289-00 - NOX Sensor 1/2 Zero Offset Too Low. P1296-00 - EGR Slow Response - Increasing Flow. P1297-00 - EGR Slow Response - Decreasing Flow. P2BA9-00 - NOX Exceedence - Insufficient Reagent Quality. P2080-00 - Exhaust Gas Temperature Sensor Circuit Performance. P2084-00 - Exhaust Gas Temperature Sensor Circuit Performance-Bank 1 Sensor 2. P0426-00 - Catalyst Temperature Sensor Circuit Performance Bank 1 Sensor 1. P242B-00 - Exhaust Gas Temperature Sensor Circuit Performance-Bank 1 Sensor 3. P062B-00 - Internal Control Module Fuel Injector Control Circuit Performance. P0088-00 - Fuel Rail Pressure Too High. P016F-00 - Closed Loop fuel Pressure Control At Limit - Pressure Too Low. P009A-00 - Intake Air Temperature / Ambient Air Temperature Correlation. P0234-00 - Turbocharger Overboost Condition. P0420-00 - Catalyst Efficiency (Bank 1). P050E-00 - Cold Start Engine Exhaust Temperature Too Low. P05F8-00 - Reductant Heater Control Module Performance. P061B-00 - Internal Control Module Torque Calculation Performance. P0128-00 - Thermostat Rationality. P1D30-00 - Oil Viscosity Too Low. P200A-00 - Intake Manifold Runner Performance - Bank 1. P200B-00 - Intake Manifold Runner Performance - Bank 2. P202E-00 - Reductant Injection Valve Circui |
|---|---|
| 18-018-14 | 2022-08-29. Service bulletin. Flash: MIL Illumination - Diagnostic and System Improvements This bulletin involves selectively erasing and reprogramming the Powertrain Control Module (PCM) with new software. Some customers may experience a condition that the Oil Life Monitor shows faster then expected oil life deterioration. Software enhancements will address this issue. Some customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the Technician may find that any of the following Diagnostic Trouble Code(s) may have been set erroneously: ? P0087-00 - FUEL RAIL PRESSURE TOO LOW ? P0088-00 - FUEL RAIL PRESSURE TOO HIGH ? P016F-00 - CLOSED LOOP FUEL PRESSURE CONTROL AT LIMIT - PRESSURE TOO LOW ? P009A-00 - INTAKE AIR TEMPERATURE / AMBIENT AIR TEMPERATURE CORRELATION ? P0234-00 - TURBOCHARGER OVERBOOST CONDITION ? P0420-00 - CATALYST EFFICIENCY (BANK 1) ? P0426-00 - CATALYST TEMPERATURE SENSOR CIRCUIT PERFORMANCE (BANK 1 SENSOR 1) ? P050E-00 - COLD START ENGINE EXHAUST TEMPERATURE TOO LOW ? P05F8-00 REDUCTANT HEATER CONTROL MODULE PERFORMANCE ? P061B-00 - INTERNAL CONTROL MODULE TORQUE CALCULATION PERFORMANCE ? P062B-00 - INTERNAL CONTROL MODULE FUEL INJECTOR CONTROL CIRCUIT PERFORMANCE ? P0128-00 - THERMOSTAT RATIONALITY ? P1D30-00 - OIL VISCOSITY TOO LOW ? P200A-00 - INTAKE MANIFOLD RUNNER PERFORMANCE - BANK 1 ? P200B-00 - INTAKE MANIFOLD RUNNER PERFORMANCE - BANK 2 ? P202E-00 - REDUCTANT INJECTION VALVE CIRCUIT PERFORMANCE ? P203E-00 - REDUCTANT LEVEL SENSOR 1 CIRCUIT INTERMITTENT/ERRATIC ? P204F-00 - REDUCTANT SYSTEM PERFORMANCE ? P2080-00 - EXHAUST GAS TEMPERATURE SENSOR CIRCUIT PERFORMANCE ? P2084-00 - EXHAUST GAS TEMPERATURE SENSOR CIRCUIT PERFORMANCE - BANK 1 SENSOR 2 ? P20BA-00 - REDUCTANT HEATER 1 CONTROL CIRCUIT PERFORMANCE ? P20BE-00 - REDUCTANT PRESSURE LINE HEATER CONTROL CIRCUIT PERFORMANCE ? P20EE-00 - SCR NOX CATALYST EFFICIENCY BELOW THRESHOLD BANK 1 ? P20C2-00 - REDUCTANT HE |
| 18-018-14 REV. B | 2022-08-22. Service bulletin. Flash: MIL Illumination - Diagnostic and System Improvements This bulletin involves selectively erasing and reprogramming the Powertrain Control Module (PCM) with new software. Some customers may experience a condition that the Oil Life Monitor shows faster then expected oil life deterioration. Software enhancements will address this issue. Some customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the Technician may find that any of the following Diagnostic Trouble Code(s) may have been set erroneously: ? P0087-00 - FUEL RAIL PRESSURE TOO LOW ? P0088-00 - FUEL RAIL PRESSURE TOO HIGH ? P016F-00 - CLOSED LOOP FUEL PRESSURE CONTROL AT LIMIT - PRESSURE TOO LOW ? P009A-00 - INTAKE AIR TEMPERATURE / AMBIENT AIR TEMPERATURE CORRELATION ? P0234-00 - TURBOCHARGER OVERBOOST CONDITION ? P0420-00 - CATALYST EFFICIENCY (BANK 1) ? P0426-00 - CATALYST TEMPERATURE SENSOR CIRCUIT PERFORMANCE (BANK 1 SENSOR 1) ? P050E-00 - COLD START ENGINE EXHAUST TEMPERATURE TOO LOW ? P05F8-00 REDUCTANT HEATER CONTROL MODULE PERFORMANCE ? P061B-00 - INTERNAL CONTROL MODULE TORQUE CALCULATION PERFORMANCE ? P062B-00 - INTERNAL CONTROL MODULE FUEL INJECTOR CONTROL CIRCUIT PERFORMANCE ? P0128-00 - THERMOSTAT RATIONALITY ? P1D30-00 - OIL VISCOSITY TOO LOW ? P200A-00 - INTAKE MANIFOLD RUNNER PERFORMANCE - BANK 1 ? P200B-00 - INTAKE MANIFOLD RUNNER PERFORMANCE - BANK 2 ? P202E-00 - REDUCTANT INJECTION VALVE CIRCUIT PERFORMANCE ? P203E-00 - REDUCTANT LEVEL SENSOR 1 CIRCUIT INTERMITTENT/ERRATIC ? P204F-00 - REDUCTANT SYSTEM PERFORMANCE ? P2080-00 - EXHAUST GAS TEMPERATURE SENSOR CIRCUIT PERFORMANCE ? P2084-00 - EXHAUST GAS TEMPERATURE SENSOR CIRCUIT PERFORMANCE - BANK 1 SENSOR 2 ? P20BA-00 - REDUCTANT HEATER 1 CONTROL CIRCUIT PERFORMANCE ? P20BE-00 - REDUCTANT PRESSURE LINE HEATER CONTROL CIRCUIT PERFORMANCE ? P20EE-00 - SCR NOX CATALYST EFFICIENCY BELOW THRESHOLD BANK 1 ? P20C2-00 - REDUCTANT HE |
| 18-018-14 REV. C | 2022-08-15. Service bulletin. Flash: MIL Illumination - Remote Start, Diagnostic and System Improvements This bulletin involves selectively erasing and reprogramming the Powertrain Control Module (PCM) with new software. Some customers may experience a condition that the Remote Start will not start the vehicle in cold 14° F (-10° C) ambient temperatures. Software enhancements will help this issue. Some customers may experience a condition that the Oil Life Monitor shows faster then expected oil life deterioration. Software enhancements will address this issue. Some customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the Technician may find that any of the following Diagnostic Trouble Code(s) may have been set erroneously: ? P0087-00 - FUEL RAIL PRESSURE TOO LOW ? P0088-00 - FUEL RAIL PRESSURE TOO HIGH ? P016F-00 - CLOSED LOOP FUEL PRESSURE CONTROL AT LIMIT - PRESSURE TOO LOW ? P009A-00 - INTAKE AIR TEMPERATURE / AMBIENT AIR TEMPERATURE CORRELATION ? P0234-00 - TURBOCHARGER OVERBOOST CONDITION ? P0420-00 - CATALYST EFFICIENCY (BANK 1) ? P0426-00 - CATALYST TEMPERATURE SENSOR CIRCUIT PERFORMANCE (BANK 1 SENSOR 1) ? P050E-00 - COLD START ENGINE EXHAUST TEMPERATURE TOO LOW ? P05F8-00 REDUCTANT HEATER CONTROL MODULE PERFORMANCE ? P061B-00 - INTERNAL CONTROL MODULE TORQUE CALCULATION PERFORMANCE ? P062B-00 - INTERNAL CONTROL MODULE FUEL INJECTOR CONTROL CIRCUIT PERFORMANCE ? P0128-00 - THERMOSTAT RATIONALITY ? P1D30-00 - OIL VISCOSITY TOO LOW ? P200A-00 - INTAKE MANIFOLD RUNNER PERFORMANCE - BANK 1 ? P200B-00 - INTAKE MANIFOLD RUNNER PERFORMANCE - BANK 2 ? P202E-00 - REDUCTANT INJECTION VALVE CIRCUIT PERFORMANCE ? P203E-00 - REDUCTANT LEVEL SENSOR 1 CIRCUIT INTERMITTENT/ERRATIC ? P204F-00 - REDUCTANT SYSTEM PERFORMANCE ? P2080-00 - EXHAUST GAS TEMPERATURE SENSOR CIRCUIT PERFORMANCE ? P2084-00 - EXHAUST GAS TEMPERATURE SENSOR CIRCUIT PERFORMANCE - BANK 1 SENSOR 2 ? P20BA-00 - REDUCTANT HEATER 1 CONTROL CIRCUI |
| 18-023-15 | 2018-09-24. Service bulletin. Flash: 3.0 L MIL Illumination Diagnostic and System Improvements This bulletin involves reprogramming the Powertrain Control Module (PCM) with the latest available software. A small number of customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the Technician may find one or more of the following Diagnostic Trouble Code(s) may have been set: ? P20C2 - Reductant Heater 3 Control Circuit Performance. ? P204F - Reductant System Performance. ? P20E9 - Reductant Pressure Too High. ? P0087-00 - Fuel Rail Pressure Too Low. ? P20EE-00 - SCR NOX Catalyst Efficiency Below Threshold Bank 1. ? P0171-00 - System Too Lean (Bank 1). ? P0172-00 - System Too Rich (Bank 1). ? P225C-00 - NOX Sensor Performance - Signal Stuck High Bank 1 Sensor 1. ? P225D-00 - NOX Sensor 1/1 Performance - Signal Stuck Low. ? P1288-00 - NOX Sensor 1/2 Zero Offset Too High. ? P1289-00 - NOX Sensor 1/2 Zero Offset Too Low. ? P1296-00 - EGR Slow Response - Increasing Flow. ? P1297-00 - EGR Slow Response - Decreasing Flow. ? P2BA9-00 - NOX Exceedence - Insufficient Reagent Quality. ? P2080-00 - Exhaust Gas Temperature Sensor Circuit Performance. ? P2084-00 - Exhaust Gas Temperature Sensor Circuit Performance-Bank 1 Sensor 2. ? P0426-00 - Catalyst Temperature Sensor Circuit Performance Bank 1 Sensor 1. ? P242B-00 - Exhaust Gas Temperature Sensor Circuit Performance-Bank 1 Sensor 3. ? P062B-00 - Internal Control Module Fuel Injector Control Circuit Performance. ? P0088-00 - Fuel Rail Pressure Too High. ? P016F-00 - Closed Loop fuel Pressure Control At Limit - Pressure Too Low. ? P009A-00 - Intake Air Temperature / Ambient Air Temperature Correlation. ? P0234-00 - Turbocharger Overboost Condition. ? P0420-00 - Catalyst Efficiency (Bank 1). ? P050E-00 - Cold Start Engine Exhaust Temperature Too Low. ? P05F8-00 - Reductant Heater Control Module Performance. ? P061B-00 - Internal Control Module Torque Calculation |
| 18-018-14 REV. C | 2018-06-18. Service bulletin. Flash: MIL Illumination - Remote Start, Diagnostic and System Improvements This bulletin involves selectively erasing and reprogramming the Powertrain Control Module (PCM) with new software. Some customers may experience a condition that the Remote Start will not start the vehicle in cold 14° F (-10° C) ambient temperatures. Software enhancements will help this issue. Some customers may experience a condition that the Oil Life Monitor shows faster then expected oil life deterioration. Software enhancements will address this issue. Some customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the Technician may find that any of the following Diagnostic Trouble Code(s) may have been set erroneously: ? P0087-00 - FUEL RAIL PRESSURE TOO LOW ? P0088-00 - FUEL RAIL PRESSURE TOO HIGH ? P016F-00 - CLOSED LOOP FUEL PRESSURE CONTROL AT LIMIT - PRESSURE TOO LOW ? P009A-00 - INTAKE AIR TEMPERATURE / AMBIENT AIR TEMPERATURE CORRELATION ? P0234-00 - TURBOCHARGER OVERBOOST CONDITION ? P0420-00 - CATALYST EFFICIENCY (BANK 1) ? P0426-00 - CATALYST TEMPERATURE SENSOR CIRCUIT PERFORMANCE (BANK 1 SENSOR 1) ? P050E-00 - COLD START ENGINE EXHAUST TEMPERATURE TOO LOW ? P05F8-00 REDUCTANT HEATER CONTROL MODULE PERFORMANCE ? P061B-00 - INTERNAL CONTROL MODULE TORQUE CALCULATION PERFORMANCE ? P062B-00 - INTERNAL CONTROL MODULE FUEL INJECTOR CONTROL CIRCUIT PERFORMANCE ? P0128-00 - THERMOSTAT RATIONALITY ? P1D30-00 - OIL VISCOSITY TOO LOW ? P200A-00 - INTAKE MANIFOLD RUNNER PERFORMANCE - BANK 1 ? P200B-00 - INTAKE MANIFOLD RUNNER PERFORMANCE - BANK 2 ? P202E-00 - REDUCTANT INJECTION VALVE CIRCUIT PERFORMANCE ? P203E-00 - REDUCTANT LEVEL SENSOR 1 CIRCUIT INTERMITTENT/ERRATIC ? P204F-00 - REDUCTANT SYSTEM PERFORMANCE ? P2080-00 - EXHAUST GAS TEMPERATURE SENSOR CIRCUIT PERFORMANCE ? P2084-00 - EXHAUST GAS TEMPERATURE SENSOR CIRCUIT PERFORMANCE - BANK 1 SENSOR 2 ? P20BA-00 - REDUCTANT HEATER 1 CONTROL CIRCUI |
| 18-018-14 REV. E | 2018-06-11. Service bulletin. Flash: 3.0 L MIL Illumination Diagnostic and System Improvements This bulletin involves reprogramming the Powertrain Control Module (PCM) with the latest available software. A small number of customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the Technician may find one or more of the following Diagnostic Trouble Code(s) may have been set: P0087-00 - Fuel Rail Pressure Too Low. P20EE-00 - SCR NOX Catalyst Efficiency Below Threshold Bank 1. P0171-00 - System Too Lean (Bank 1). P0172-00 - System Too Rich (Bank 1). P225C-00 - NOX Sensor Performance - Signal Stuck High Bank 1 Sensor 1. P225D-00 - NOX Sensor 1/1 Performance - Signal Stuck Low. P1288-00 - NOX Sensor 1/2 Zero Offset Too High. P1289-00 - NOX Sensor 1/2 Zero Offset Too Low. P1296-00 - EGR Slow Response - Increasing Flow. P1297-00 - EGR Slow Response - Decreasing Flow. P2BA9-00 - NOX Exceedence - Insufficient Reagent Quality. P2080-00 - Exhaust Gas Temperature Sensor Circuit Performance. P2084-00 - Exhaust Gas Temperature Sensor Circuit Performance-Bank 1 Sensor 2. P0426-00 - Catalyst Temperature Sensor Circuit Performance Bank 1 Sensor 1. P242B-00 - Exhaust Gas Temperature Sensor Circuit Performance-Bank 1 Sensor 3. P062B-00 - Internal Control Module Fuel Injector Control Circuit Performance. P0088-00 - Fuel Rail Pressure Too High. P016F-00 - Closed Loop fuel Pressure Control At Limit - Pressure Too Low. P009A-00 - Intake Air Temperature / Ambient Air Temperature Correlation. P0234-00 - Turbocharger Overboost Condition. P0420-00 - Catalyst Efficiency (Bank 1). P050E-00 - Cold Start Engine Exhaust Temperature Too Low. P05F8-00 - Reductant Heater Control Module Performance. P061B-00 - Internal Control Module Torque Calculation Performance. P0128-00 - Thermostat Rationality P1D30-00 - Oil Viscosity Too Low P200A-00 - Intake Manifold Runner Performance - Bank 1 P200B-00 - Intake Manifold Runner Performance - Bank 2 |
| 18-018-14 REV. D | 2018-06-11. Service bulletin. Flash: MIL Illumination Diagnostic and System Improvements This bulletin involves selectively erasing and reprogramming the Powertrain Control Module (PCM) with new software. A small number of customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the Technician may find one or more of the following Diagnostic Trouble Code(s) may have been set erroneously: ? P0087-00 - Fuel Rail Pressure Too Low. ? P20EE-00 - SCR NOX Catalyst Efficiency Below Threshold Bank 1. ? P0171-00 - System Too Lean (Bank 1). ? P0172-00 - System Too Rich (Bank 1). ? P225C-00 - NOX Sensor Performance - Signal Stuck High Bank 1 Sensor 1. ? P225D-00 - NOX Sensor 1/1 Performance - Signal Stuck Low. ? P1288-00 - NOX Sensor 1/2 Zero Offset Too High. ? P1289-00 - NOX Sensor 1/2 Zero Offset Too High. ? P1296-00 - EGR Slow Response - Increasing Flow. ? P1297-00 - EGR Slow Response - Decreasing Flow. ? P2BA9-00 - NOX Exceedence - Insufficient Reagent Quality. ? P2080-00 - Exhaust Gas Temperature Sensor Circuit Performance. ? P2084-00 - Exhaust Gas Temperature Sensor Circuit Performance-Bank 1 Sensor 2. ? P0426-00 - Catalyst Temperature Sensor Circuit Performance Bank 1 Sensor 1. ? P242B-00 - Exhaust Gas Temperature Sensor Circuit Performance-Bank 1 Sensor 3. ? P062B-00 - Internal Control Module Fuel Injector Control Circuit Performance. ? P0088-00 - Fuel Rail Pressure Too High. ? P016F-00 - Closed Loop fuel Pressure Control At Limit - Pressure Too Low. ? P009A-00 - Intake Air Temperature / Ambient Air Temperature Correlation. ? P0234-00 - Turbocharger Overboost Condition. ? P0420-00 - Catalyst Efficiency (Bank 1). ? P050E-00 - Cold Start Engine Exhaust Temperature Too Low. ? P05F8-00 - Reductant Heater Control Module Performance. ? P061B-00 - Internal Control Module Torque Calculation Performance. ? P0128-00 - Thermostat Rationality. ? P1D30-00 - Oil Viscosity Too Low. ? P200A-00 - Intake Manifold Runne |
| 18-018-14 REV. B | 2018-06-11. Service bulletin. Flash: MIL Illumination - Diagnostic and System Improvements This bulletin involves selectively erasing and reprogramming the Powertrain Control Module (PCM) with new software. Some customers may experience a condition that the Oil Life Monitor shows faster then expected oil life deterioration. Software enhancements will address this issue. Some customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the Technician may find that any of the following Diagnostic Trouble Code(s) may have been set erroneously: ? P0087-00 - FUEL RAIL PRESSURE TOO LOW ? P0088-00 - FUEL RAIL PRESSURE TOO HIGH ? P016F-00 - CLOSED LOOP FUEL PRESSURE CONTROL AT LIMIT - PRESSURE TOO LOW ? P009A-00 - INTAKE AIR TEMPERATURE / AMBIENT AIR TEMPERATURE CORRELATION ? P0234-00 - TURBOCHARGER OVERBOOST CONDITION ? P0420-00 - CATALYST EFFICIENCY (BANK 1) ? P0426-00 - CATALYST TEMPERATURE SENSOR CIRCUIT PERFORMANCE (BANK 1 SENSOR 1) ? P050E-00 - COLD START ENGINE EXHAUST TEMPERATURE TOO LOW ? P05F8-00 REDUCTANT HEATER CONTROL MODULE PERFORMANCE ? P061B-00 - INTERNAL CONTROL MODULE TORQUE CALCULATION PERFORMANCE ? P062B-00 - INTERNAL CONTROL MODULE FUEL INJECTOR CONTROL CIRCUIT PERFORMANCE ? P0128-00 - THERMOSTAT RATIONALITY ? P1D30-00 - OIL VISCOSITY TOO LOW ? P200A-00 - INTAKE MANIFOLD RUNNER PERFORMANCE - BANK 1 ? P200B-00 - INTAKE MANIFOLD RUNNER PERFORMANCE - BANK 2 ? P202E-00 - REDUCTANT INJECTION VALVE CIRCUIT PERFORMANCE ? P203E-00 - REDUCTANT LEVEL SENSOR 1 CIRCUIT INTERMITTENT/ERRATIC ? P204F-00 - REDUCTANT SYSTEM PERFORMANCE ? P2080-00 - EXHAUST GAS TEMPERATURE SENSOR CIRCUIT PERFORMANCE ? P2084-00 - EXHAUST GAS TEMPERATURE SENSOR CIRCUIT PERFORMANCE - BANK 1 SENSOR 2 ? P20BA-00 - REDUCTANT HEATER 1 CONTROL CIRCUIT PERFORMANCE ? P20BE-00 - REDUCTANT PRESSURE LINE HEATER CONTROL CIRCUIT PERFORMANCE ? P20EE-00 - SCR NOX CATALYST EFFICIENCY BELOW THRESHOLD BANK 1 ? P20C2-00 - REDUCTANT HE |
| 18-018-14 REV. A | 2018-05-21. Service bulletin. Flash: MIL Illumination - Diagnostic and System Improvements This bulletin involves selectively erasing and reprogramming the Powertrain Control Module (PCM) with new software. Some customers may experience a condition that the Oil Life Monitor shows faster then expected oil life deterioration. Software enhancements will address this issue. Some customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the Technician may find that any of the following Diagnostic Trouble Code(s) may have been set: ? P0073 - AMBIENT AIR TEMPERATURE SENSOR CIRCUIT HIGH ? P0088 - FUEL RAIL PRESSURE TOO HIGH ? P016F - CLOSED LOOP FUEL PRESSURE CONTROL AT LIMIT - PRESSURE TOO LOW ? P0420 - CATALYST EFFICIENCY (BANK 1) ? P0426 - CATALYST TEMPERATURE SENSOR CIRCUIT PERFORMANCE (BANK 1 SENSOR 1) ? P05F8 - REDUCTANT HEATER CONTROL MODULE PERFORMANCE ? P061B - INTERNAL CONTROL MODULE TORQUE CALCULATION PERFORMANCE ? P062B - INTERNAL CONTROL MODULE FUEL INJECTOR CONTROL CIRCUIT PERFORMANCE ? P1D30 - OIL VISCOSITY TOO LOW ? P200A - INTAKE MANIFOLD RUNNER PERFORMANCE - BANK 1 ? P200B - INTAKE MANIFOLD RUNNER PERFORMANCE - BANK 2 ? P20BA - REDUCTANT HEATER 1 CONTROL CIRCUIT PERFORMANCE ? P20EE - SCR NOX CATALYST EFFICIENCY BELOW THRESHOLD BANK 1 ? P203E - REDUCTANT LEVEL SENSOR 1 CIRCUIT INTERMITTENT/ERRATIC ? P2080 - EXHAUST GAS TEMPERATURE SENSOR CIRCUIT PERFORMANCE ? P2084 - EXHAUST GAS TEMPERATURE SENSOR CIRCUIT PERFORMANCE - BANK 1 SENSOR 2 ? P242B - EXHAUST GAS TEMPERATURE SENSOR CIRCUIT PERFORMANCE - BANK1 SENSOR 3 ? P2463 - DIESEL PARTICULATE FILTER - SOOT ACCUMULATION ? P24C2 - EXHAUST GAS TEMPERATURE MEASUREMENT SYSTEM - MULTIPLE SENSOR CORRELATION BANK 1 ? P24F2 - EGR TEMPERATURE/CHARGE AIR COOLER TEMPERATURE CORRELATION ? U12A3 - LOST COMMUNICATION WITH PM SENSOR |
11 on file from NHTSA, as of 2026-10-19. See them in the bulletin list. A bulletin lists model years: read the document for which vehicles it concerns.