WenmarOpen by Wenmar Pro

Service bulletins for the 2018 Jeep Compass

A bulletin is a manufacturer's communication to its dealers, as NHTSA indexes it. The summary is NHTSA's. The document is the manufacturer's: read it at NHTSA. A bulletin is not a recall, and listing a model year does not mean every vehicle of it is concerned.

333 on file from NHTSA, as of 2026-10-19.

By type

By component

By trouble code

By topic

Only bulletins with component: Body and frame are shown. Show all

Bulletins, newest first
S2523000003 REV.A2026-04-29. Service bulletin. STRUCTURE:BODY; ELECTRICAL SYSTEM. Door Latch, Handle And Ajar Additional Service Information.
08-075-262026-03-05. Service bulletin. STRUCTURE:BODY; ELECTRICAL SYSTEM. Rear Taillamp Condensation Clearing Procedure On occasion, vehicle exterior taillamp assemblies get fogged with a light layer of condensation on the SYMPTOM: inside of the lenses Fig. 1. This may be reported after the lamps have been turned on and brought up to operating temperature, turned off and then rapidly cooled by cold water (such as rain, or the water from a vehicle wash). Lens fogging can also occur under certain atmospheric conditions after a vehicle has been parked outside overnight (i.e. a warm humid day followed by clear cool night). This will usually clear as atmospheric conditions change to allow the condensation to change back into a vapor. Turning the taillamps on will usually accelerate this process. This bulletin is to communicate the procedure for rear taillamp condensation clearing.
31-001-25 REV. A2025-08-21. Service bulletin. STRUCTURE:BODY. Aluminum Body Panel Corrosion Repair Aluminum corrosion or bubbling along the leading edge of hood, hinges or other exterior surface areas of the hinges, doors, fenders, swing gates or liftgates.
31-001-25 REV. B2025-08-21. Service bulletin. STRUCTURE:BODY. Aluminum Body Panel Corrosion Repair Aluminum corrosion or bubbling along the leading edge of hood, hinges or other exterior surface areas of the hinges, doors, fenders, swing gates or liftgates.
31-001-252025-08-21. Service bulletin. STRUCTURE:BODY. Aluminum Body Panel Corrosion Repair Aluminum corrosion or bubbling along the leading edge of hood, hinges or other exterior surface areas of the hinges, doors, fenders, swing gates or liftgates
1057702025-08-06. Service bulletin. STRUCTURE:BODY. PROP - LIFTGATE
08-220-252025-07-31. Service bulletin. STRUCTURE:BODY. Rear Taillamp Condensation Clearing Procedure On occasion, vehicle exterior taillamp assemblies are fogged with a light layer of condensation on the inside of the lenses Fig. 1. This may be reported after the lamps have been turned on and brought up to operating temperature, turned off and then rapidly cooled by cold water (such as rain, or the water from a vehicle wash). Lens fogging can also occur under certain atmospheric conditions after a vehicle has been parked outside overnight (i.e. a warm humid day followed by clear cool night). This will usually clear as atmospheric conditions change to allow the condensation to change back into a vapor. Turning the taillamps on will usually accelerate this process. This bulletin is to communicate the procedure for rear taillamp condensation clearing.
S25230000032025-01-16. Service bulletin. STRUCTURE:BODY. Door Latch, Handle And Ajar Additional Service Information.
31-001-242024-07-30. Service bulletin. STRUCTURE:BODY. "Aluminum Body Panel Corrosion Repair Aluminum corrosion or bubbling along the leading edge of hood, hinges or other exterior surface areas of the hinges, doors, fenders, swing gates or liftgates. NOTE: Verify current warranty policy to determine if digital imaging pre-authorization is required or pre-approval is required from the Regional Office; depending on market. This bulletin involves inspecting and if necessary removing corrosion and refinishing the suspect aluminum panels on the vehicle, hood, door, fenders, hinges, swing gates or liftgate panels."
08-153-242024-07-02. Service bulletin. STRUCTURE:BODY. "Rear Taillamp Condensation Clearing Procedure On occasion, vehicle exterior taillamp assemblies are fogged with a light layer of condensation on the inside of the lenses Fig. 1. This may be reported after the lamps have been turned on and brought up to operating temperature, turned off and then rapidly cooled by cold water (such as rain, or the water from a vehicle wash). Lens fogging can also occur under certain atmospheric conditions after a vehicle has been parked outside overnight (i.e. a warm humid day followed by clear cool night). This will usually clear as atmospheric conditions change to allow the condensation to change back into a vapor. Turning the taillamps on will usually accelerate this process. This bulletin is to communicate the procedure for rear taillamp condensation clearing."
31001232024-01-02. Service bulletin. STRUCTURE. Aluminum Body Panel Corrosion Repair Aluminum corrosion or bubbling along the leading edge of hood, hinges or other exterior surface areas of the hinges, doors, fenders, swing gates or liftgates. NOTE: **Verify current warranty policy to determine if digital imaging pre authorization is required or Pre Approval is required from Regional Office depending on market.** This bulletin involves inspecting and if necessary removing corrosion and refinishing the suspect aluminum panels on the vehicle, hood, door, fenders, hinges, swing gates or liftgate panels.
31001232023-04-17. Service bulletin. STRUCTURE. Aluminum Body Panel Corrosion Repair Aluminum corrosion or bubbling along the leading edge of hood, hinges or other exterior surface areas of the hinges, doors, fenders, swing gates or liftgates. NOTE: **Verify current warranty policy to determine if digital imaging pre authorization is required or Pre Approval is required from Regional Office depending on market.** This bulletin involves inspecting and if necessary removing corrosion and refinishing the suspect aluminum panels on the vehicle, hood, door, fenders, hinges, swing gates or liftgate panels.
31-002-222023-01-17. Service bulletin. STRUCTURE. Aluminum Body Panel Corrosion Repair Aluminum corrosion or bubbling along the leading edge of hood, hinges or other exterior surface areas of the hinges, doors, fenders, swing gates or liftgates. NOTE: Digital imaging pre authorization is required for Smart Warranty Base dealers or Pre Approval is required from Regional Office depending on market. This bulletin involves inspecting and if necessary removing corrosion and refinishing the suspect aluminum panels on the vehicle, hood, door, fenders, hinges, swing gates or liftgate panels.
31001222023-01-09. Service bulletin. STRUCTURE. Approved Use of Weld Through Primers This bulletin documents the FCA US LLC position regarding the use of weld through primer when using Squeeze Type Resistance Spot Welding (STRSW) and Gas Metal Arc Welding (GMAW) processes when welding steel body panels and structural components.
08071202023-01-09. Service bulletin. FUEL SYSTEM, GASOLINE; STRUCTURE. Interior Water Intrusion Through HVAC Air Inlet This bulletin involves installing new stud clips on the headlamp wiring harness, inspecting and possibly replacing, the cowl panel cover, instrument panel insulator and front carpets for water intrusion. The customer may describe one or more of the following:The front passenger floor carpets or mats are wet. An unpleasant cabin odor. Water leakage from behind the instrument panel.
S20210000042023-01-09. Service bulletin. POWER TRAIN; STRUCTURE. Valve Body Learn Procedure On WiTech Shows The Transmission Is Not In The Proper Gear After Repairs
31001222022-10-31. Service bulletin. STRUCTURE. Approved Use of Weld Through Primers This bulletin documents the FCA US LLC position regarding the use of weld through primer when using Squeeze Type Resistance Spot Welding (STRSW) and Gas Metal Arc Welding (GMAW) processes when welding steel body panels and structural components.
31001222022-10-31. Service bulletin. STRUCTURE:INTERIOR PANELS:DOOR; STRUCTURE; UNKNOWN OR OTHER. Approved Use of Weld Through Primers This bulletin documents the FCA US LLC position regarding the use of weld through primer when using Squeeze Type Resistance Spot Welding (STRSW) and Gas Metal Arc Welding (GMAW) processes when welding steel body panels and structural components.
23046172022-10-31. Service bulletin. ELECTRICAL SYSTEM; STRUCTURE. Water Entering Body Grommet at A-Pillar Plug Area This bulletin involves removing two grommets at the body side A-pillar and installing Tesa tape covers, also with the potential need for terminal repair. The customer may experience an inoperable windows.
2304617REVA2022-10-31. Service bulletin. STRUCTURE; ELECTRICAL SYSTEM. Water Entering Body Grommet at A-Pillar Plug Area This bulletin involves removing two grommets at the body side A-pillar and installing Tesa tape covers, also with the potential need for terminal repair. The customer may experience an inoperable windows.
31002202022-10-17. Service bulletin. STRUCTURE. Aluminum Body Panel Corrosion Repair This bulletin involves inspecting and if necessary removing corrosion and refinishingthe suspect aluminum panels on the vehicle, hood, door, fenders, hinges, swing gates or liftgate panels.
08002222022-10-17. Service bulletin. STRUCTURE; ELECTRICAL SYSTEM. This bulletin involves reprogramming the Body Control Module (BCM) with the latest available software.
90044532022-10-17. Service bulletin. STRUCTURE; POWER TRAIN; BACK OVER PREVENTION; STEERING; WHEELS. GEAR, Rack and Pinion If looking to replace the rack and pinion due to a clunking / knocking noise, please use the Chassis Ear Tool to pinpoint the exact location of the noise following the proper diagnostics. The points where you should place the chassis ear tool in sequence are: steering column, rack and pinion, intermediate shaft or the outer tie rod of the rack and pinion. Also ensure all related components are properly torqued such as shock absorbers, steering column, lower ball joints, stabilizer links, sway bar links and cradle mount bolts (front and rear). Please contact FCA Redacted Content for feedback related ONLY to this GPOP Tech Tip. Do Not email regarding repair procedures unrelated to this Tech Tip or part order inquiries.
31005192022-09-15. Service bulletin. STRUCTURE. Use of Aftermarket Parts This bulletin involves discussing FCA US LLC position with regard to collision repair industry awareness regarding the use of aftermarket parts.
31003192022-09-15. Service bulletin. STRUCTURE. Use of Salvage/Recycled Parts This bulletin involves discussing FCA US LLC position with regard to collision repair industry awareness regarding the use of recycled or salvage parts.

The summaries are NHTSA's. Each bulletin's page links NHTSA's copy of the manufacturer's document.