Service bulletins for the 2016 Jeep Cherokee
A bulletin is a manufacturer's communication to its dealers, as NHTSA indexes it. The summary is NHTSA's. The document is the manufacturer's: read it at NHTSA. A bulletin is not a recall, and listing a model year does not mean every vehicle of it is concerned.
450 on file from NHTSA, as of 2026-10-19.
By type
By component
By trouble code
Only bulletins with component: Engine are shown. Show all
| S1809000007 Rev. | 2021-04-26. Service bulletin. ENGINE AND ENGINE COOLING. Customer complaint may include engine oil leak/consumption. |
|---|---|
| 9003357 | 2021-04-26. Service bulletin. ENGINE AND ENGINE COOLING. ADAPTER, Engine Oil Filter (Pentastar V6) All vehicles equipped with a 3.2L or 3.6L except for model year 2014 vehicles with leak concern: 1) Ensure the Oil Filter Adapter (OFA) Cap O-ring is seated in the proper groove in the cap and not damaged or cut. 2) If replacing the (OFA) due to a leak detected between (OFA) and block. Ensure the torque on the 5 bolts are torqued to 12nm. If not record the actual values, torque to 12nm and contact the FCA employees listed below. 3) Remove the (OFA) and replace the O-ring and gaskets only (Kit #68191356A$), NOT THE OFA. 4) If oil was drained, add oil dye to ensure the leak is repaired. For model year 2014 vehicles replace the Oil Filter Adaptor. 5) When replacing PN's 68310865A$ & 68308741A$, it may be necessary to transfer the Oil Temp/Pressure Sensor from the old OFA to the new OFA. |
| 09-002-21 | 2021-03-15. Service bulletin. ENGINE AND ENGINE COOLING. 2.0L or 2.4L Engine Replacement This bulletin involves replacing the long block due to a crankshaft imbalance condition. These vehicles may exhibit a vibration in the engine. |
| 18-002-16 REV. C | 2020-10-26. Service bulletin. ELECTRICAL SYSTEM; POWER TRAIN; EQUIPMENT:APPLIANCE:AIR CONDITIONER; ENGINE AND ENGINE COOLING. Flash: Diagnostic And System Improvements This bulletin involves reprogramming the Powertrain Control Module (PCM) with the latest available software. Customers may experience a Malfunction Indicator Lamp (MIL) illumination, or a slight push in the vehicle may be felt when coasting down while the transmission shifts from 8th to 7th gear. Upon further investigation, the technician may find the following Diagnostic Trouble Codes (DTCs) set in the PCM memory: · **U1424 - Implausible Engine Torque Signal Received DTC False Failure. · P2097 - Downstream Fuel Trim System 1 Rich DTC Calibration Robustness Improvement. · P2099 - Downstream Fuel Trim System 2 Rich DTC Calibration Robustness Improvement.** · U0402 - Implausible Data Received. · B10EA - Blower Motor Control Circuit High. · B10E9 - Blower Motor Control Circuit Low. · P0456 - EVAP System Small Leak. In addition the following enhancements is included: · Vehicle shudder at stop/start with A/C on. |
| 18-064-20 | 2020-09-28. Service bulletin. STEERING; ENGINE AND ENGINE COOLING; POWER TRAIN:AUTOMATIC TRANSMISSION:CONTROL MODULE (TCM/PCM/TECM); ELECTRICAL SYSTEM. Flash: Powertrain Control Module (PCM) Updates This bulletin involves reprogramming the PCM with the latest available software. Customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find one or more of the following DTCs:P2610 - PCM Internal Engine Off Timer Performance. U1504 - Implausible Message Data Length Received From Steering Angle Sensor. U1424 - Implausible Engine Torque Signal Received DTC False Failure. P2097 - Downstream Fuel Trim System 1 Rich DTC Calibration Robustness Improvement. P2099 - Downstream Fuel Trim System 2 Rich DTC Calibration Robustness Improvement. U0402 - Implausible Data Received. B10EA - Blower Motor Control Circuit High. B10E9 - Blower Motor Control Circuit Low. P0456 - EVAP System Small Leak. In addition, the following software enhancements are available:Calibration update to allow the throttle body to be cycled while the engine is off, for diagnostic purposes. Calibration update for a slight push in the vehicle that may be felt when coasting down during a 8th to 7th gear downshift. Vehicle shudder at stop/start with A/C on. |
| S2008000113 | 2020-09-28. Service bulletin. ENGINE; ELECTRICAL SYSTEM. No Start Intermittently, Vehicle Requires Multiple Keyless Push To Start Attempts To Start Vehicle |
| 09-006-20 REV. B | 2020-08-24. Service bulletin. ENGINE AND ENGINE COOLING. 2.4L Engine Oil Consumption Test This bulletin involves performing an oil consumption verification test. The customer may comment that the vehicles engine oil level is low or they need to add oil between oil change intervals and no visible signs of oil leaking from the engine. |
| 09-006-20 REV. A | 2020-06-22. Service bulletin. ENGINE. 2.4L Engine Oil Consumption Test This bulletin involves performing an oil consumption verification test. The customer may comment that the vehicles engine oil level is low or they need to add oil between oil change intervals and no visible signs of oil leaking from the engine. |
| 09-006-20 | 2020-06-22. Service bulletin. ENGINE. 2.4L Engine Oil Consumption Test This bulletin involves performing an oil consumption verification test. The customer may comment that the vehicles engine oil level is low or they need to add oil between oil change intervals and no visible signs of oil leaking from the engine. |
| 18-089-19 | 2019-12-16. Service bulletin. FUEL SYSTEM, GASOLINE; ENGINE. wiTECH Small Leak Verification Test (SLVT) - P0456-EVAP SYSTEM SMALL LEAK |
| 9003968 | 2019-10-28. Service bulletin. ENGINE AND ENGINE COOLING; ELECTRICAL SYSTEM; ENGINE. CONDENSER, Air Conditioning If it is determined that the A/C compressor does not engage due to a refrigerant leak at the receiver/drier plug on the A/C condenser, order the receiver/drier plug kit P/N 68447796A$ and follow the repair instructions included on the instruction sheet. |
| 18-107-15 | 2019-05-20. Service bulletin. ELECTRICAL SYSTEM; ENGINE AND ENGINE COOLING; POWER TRAIN. Flash: Diagnostic And System Improvements This bulletin involves reprogramming the Powertrain Control Module (PCM) with the latest available software. A small number of customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation, the technician may find the following Diagnostic Trouble Codes (DTCs) set in the PCM memory: ? B10EA - Blower Motor Control Circuit High. ? B10E9 - Blower Motor Control Circuit Low. ? P0456 - EVAP System Small Leak. In addition the customer may notice the following condition: ? Vehicle shudder at stop/start with A/C on. |
| 21-059-15 | 2019-05-20. Service bulletin. ENGINE; EQUIPMENT; POWER TRAIN. Flash: Transmission Diagnostic And Shift Enhancements This bulletin involves reprogramming the Transmission Control Module (TCM) with the latest available software. 2.4L Engine (Sales Code ED6) Some customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation, a technician may find the following Diagnostic Trouble Code (DTC) stored in the TCM memory: ? P061B - Internal Control Module Torque Calculation Performance. In addition, some customers may experience one or more of the following conditions: ? Less than desired low speed drivability and response to accelerator pedal input. ? Less than desired 5-4 coast down transmission shift quality. ? Less than desired transmission shift quality. ? Transmission is slow to upshift after releasing the accelerator pedal. 3.2L Engine (Sales Code EBH) Some customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation, a technician may find the following Diagnostic Trouble Code (DTC) stored in the TCM memory: ? P061B - Internal Control Module Torque Calculation Performance. In addition, some customers may experience one or more of the following conditions: ? Less than desired low speed drivability and response to accelerator pedal input. ? Less than desired 5-4 coast down transmission shift quality. ? Less than desired transmission shift quality. ? Less than optimal transmission shift timing, driving up and down hills. ? Less than desired Engine Stop/Start re-engagement or smoothness. ? Transmission is slow to upshift after releasing the accelerator pedal. |
| 18-068-16 | 2018-06-11. Service bulletin. ENGINE AND ENGINE COOLING. MIL Illumination: DTCs P112C and/or P112D This bulletin involves replacing the Post Catalyst Position O2 Sensor. A small number of customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find the following Diagnostic Trouble Codes (DTCs) stored or active: · P112C - O2 Sensor 2/1 Pumping Undercurrent. · P112D - O2 Sensor 2/1 Pumping Overcurrent. |
| 09-008-16 | 2018-06-11. Service bulletin. ENGINE AND ENGINE COOLING. 2.0L Or 2.4L Engine Replacement This bulletin involves replacing the long block due to a crankshaft imbalance condition. These vehicles may exhibit a vibration in the engine. |
| 9003694 | 2018-06-11. Service bulletin. ENGINE AND ENGINE COOLING. Oil Pump Assembly If error code P06DD present on any Pentastar V6 application, please inspect oil pump for relief valve failure. See photo attached. If valve is found out of place please call Bob Jackson (248) 944-0466 bob.jackson@fcagroup.com, or Joe Lovell (734) 309-6467 joe.lovell@fcagroup.com before proceeding. If unable to reach after 15 minutes record the following information and proceed with oil pump replacement and hold part for return to FCA via Fastrack system |
| 05184546A | 2018-06-11. Service bulletin. ENGINE AND ENGINE COOLING. 3.6L Oil Pan Drain Plug and Pan: When an oil pan leak is detected and the oil drain plug is loose please on JK/KL models call one of the following people. If your call in not answered within 15 minutes please proceed with the repair. First: Joe Lovell Cell (734) 309-6467 - joe.lovell@fcagroup.com Second: Scott Kucharek Cell (248) 260-0725 - scott.kucharek@fcagroup.com Third: Jermanjit Dhillon Cell (248) 260-0725 - jermanjit.dhillon@fcagroup.com |
| 23-015-16 | 2018-06-04. Service bulletin. ENGINE AND ENGINE COOLING; STRUCTURE:BODY. Water On Front Carpet Or In Rocker Side Sill This bulletin involves visually inspecting the sealer on the engine bulkhead area and water testing to diagnose leak path. Then repairing body seam leaks with sealer. The customer may describe damp or wet carpet in the front footwell or in the rocker sill. This condition is primarily found on the left side but may be on the right (Fig. 1) or both footwells. The cause of this leak may be due to a sealant void on the body seam, allowing water to enter the vehicle interior. |
| 23-015-16 REV. A | 2018-06-04. Service bulletin. ENGINE AND ENGINE COOLING; EQUIPMENT; STRUCTURE. Water On Front Carpet Or In Rocker Side Sill This bulletin involves visually inspecting the sealer on the engine bulkhead area and water testing to diagnose leak path. Then repairing body seam leaks with sealer. The customer may describe damp or wet carpet in the front footwell or in the rocker sill. This condition is primarily found on the left side but may be on the right (Fig. 1) or both footwells. The cause of this leak may be due to a sealant void on the body seam, allowing water to enter the vehicle interior. |
| 18-014-16 REV. A | 2018-06-04. Service bulletin. POWER TRAIN; ELECTRICAL SYSTEM; EQUIPMENT; ENGINE. Flash: 2.4L Powertrain Diagnostic And System Improvements This bulletin involves reprogramming the Powertrain Control Module (PCM) with the latest available software. A small number of customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation, the technician may find one or more of the following Diagnostic Trouble Codes (DTCs): · P0101 - Mass Air Flow Sensor "A" Circuit Performance. · P0335 - Crankshaft Position Sensor Circuit. · P0133 - O2 Sensor 1/1 Slow Response. · P1607 - PCM Internal Shutdown Timer Rationality. · P2610 - PCM Internal Engine Off Timer Performance. · B104D - Blend Door Control Circuit Low. · U0402 - Implausible Data Received From TCM. · U1424 - Implausible Engine Torque Signal Received. In addition, some customers may experience the following: · A Transmission Tip-In Bump (when accelerating out of 4th gear). |
| 9003357 | 2018-06-04. Service bulletin. ENGINE AND ENGINE COOLING. Pentastar Oil Filter Adapter All vehicles equipped with a 3.2L or 3.6L engine; If replacing the Oil Filter Adapter (OFA) due to a leak detected between OFA and block, an O-ring kit (68191356AA) is now available to repair OFA/Block Interface leaks. Using dye will assist in determining source of leak. Ensure OFA Cap Oring is seated in the proper groove in the cap and not damaged or cut. Engineering is seeking information regarding OFA leaks. Questions/info can be directed to: Bob Jackson Cell (248) 944-0466 - bob.jackson@fcagroup.com Ron Dallison Cell (248-292-9510) ron.dallison@fcagroup.com Joe Lovell Cell (734) 309-6467 - joe.lovell@fcagroup.com If a response is not received within 15 mins, then proceed with the necessary repair. |
| RL108213A$ | 2017-11-03. Service bulletin. ENGINE AND ENGINE COOLING. NAG1 (5A580) Valve Body As per Warranty Bulletin D-13-22, please use R2108213A$ valve body for all Warranty (W), Mopar (M) and Mopar Vehicle Protection (F) claims.~ Assembly also includes Filter (52108325AA) and Gasket (52108332AA).~ |
| 68103198A$ | 2017-11-03. Service bulletin. ENGINE AND ENGINE COOLING. A/C Compressor This applies to 2015 and 2016 KL, UF and PF. Before replacing the AC compressor for noise, leaks , or for an inop condition:~ After these questions have been answered please call one of the individuals below.~ 1) Check all AC plumbing connection for leaks with UV light. Any leaks found?~ 2) Does compressor pulley and clutch hub turn freely, or are they seized?~ 3) What was the amount of the recovered refrigerant?~ After these questions have been answered please call one of the individuals below:~ Stev at cell (248) 867-0061~ Mark Briolat at cell (248) 345-0127~ If no response in 15 minutes, please continue with repair.~ If the compressor is replaced, then:~ 4) Drain oil from compressor. What was quantity of oil recovered? |
| 68232614A$ | 2017-11-03. Service bulletin. ENGINE AND ENGINE COOLING. Intake Manifold Gasket Intake Manifold Gaskets on Pentastar Upgrade (Sales Code ERC/ERF) are reusable provided they are not cut, torn or melted. The gaskets are not required by warranty to be replaced like they are on Pentastar Classic (ERB/EHB). The new gaskets are not interchangeable with Pentastar Classic Intake Manifold Gaskets. |
| 18-007-16 | 2017-10-21. Service bulletin. ENGINE; ELECTRICAL SYSTEM. Flash: 2.4L Powertrain Diagnostic And System Improvements This bulletin involves reprogramming the Powertrain Control Module (PCM) with the latest available software. Some customers may experience an engine stop start failure while driving. The customer may describe that when the brake pedal is released immediately after the vehicle enters Electronic Start Stop Mode (ESS), the engine turns off and wont restart until you shift to park and cycle the key. |
The summaries are NHTSA's. Each bulletin's page links NHTSA's copy of the manufacturer's document.