WenmarOpen by Wenmar Pro

Service bulletins for the 2015 Jeep Cherokee

A bulletin is a manufacturer's communication to its dealers, as NHTSA indexes it. The summary is NHTSA's. The document is the manufacturer's: read it at NHTSA. A bulletin is not a recall, and listing a model year does not mean every vehicle of it is concerned.

613 on file from NHTSA, as of 2026-10-19.

By type

By component

By trouble code

Bulletins, newest first
08039162022-08-22. Service bulletin. ENGINE. This bulletin involves inspecting the wire harness and installing mastic patch. If rub through
08038162022-08-22. Service bulletin. PARKING BRAKE; ELECTRICAL SYSTEM. This bulletin involves updating the Electronic Parking Brake (EPB) module software.
08026162022-08-22. Service bulletin. ELECTRICAL SYSTEM: INSTRUMENT CLUSTER/PANEL. Flash: Instrument Cluster Displays Incorrect.
08022162022-08-22. Service bulletin. EQUIPMENT. Accessory Kit to Enhance Flat Tow Performance.
06001162022-08-22. Service bulletin. POWER TRAIN:AUTOMATIC TRANSMISSION:INTERNAL:CLUTCHES/BANDS. Clutch Pedal Operation X62 Extended Warranty.
68264880A2022-08-15. Service bulletin. EQUIPMENT; ELECTRICAL SYSTEM; SEAT BELTS. Occupant Restraint Controller (ORC) For PF, KL or UF Vehicles ONLY:~ Prior to replacing ORC part numbers, please contact FCA engineering if the following Diagnostic trouble codes are Stored or Active in the ORC module:~ DTC: B223D-00 - OCM DTC Present~ DTC: B0050-13 - Driver Seatbelt Sensor-Circuit Open~ DTC: B0052-13 - Passenger Seatbelt Sensor-Circuit Open~ DTC: B00B5-13 - Driver Seat Track Position Restraints Sensor-Circuit Open~ DTC: B00C5-13 - Passenger Seat Track Position Restraints Sensor-Circuit Open~ DTC: B0028-13 - Right Side Seat Deployment Squib 1-Circuit Open~ DTC: B0020-13 - Left Side Seat Deployment Squib 1-Circuit Open~ Execute DealerCONNECT / TechCONNECT Diagnostic Procedures to assess potential defects to devices connected to the ORC Module depending on the active or stored Diagnostic Trouble Code. If no defects are detected, verify wiring connectivity between the ORC Module and the component associated with the Diagnostic Trouble Code. Investigate connector pins and wire harness terminals for bent,corroded,or spread conditions. If no response within 15 minutes, proceed with repair.~ FCA Engineering Contacts:~ Jay Nagle (ORC Module, OCM module, Driver/passenger seat track position sensor for PF, KL or UF Vehicles ONLY) @ cell (248) 420-4294 or jay.nagle@external.fcagroup.com~ Bill Winfrey (Driver/Passenger Buckle Switch, Passenger/Driver Seat Thorax Airbags) @ cell (248) 941-9221 or william.winfrey@fcagroup.com
18-068-162022-08-08. Service bulletin. ELECTRICAL SYSTEM; ENGINE AND ENGINE COOLING. MIL Illumination: DTCs P112C and/or P112D This bulletin involves replacing the Post Catalyst Position O2 Sensor. A small number of customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find the following Diagnostic Trouble Codes (DTCs) stored or active: · P112C - O2 Sensor 2/1 Pumping Undercurrent. · P112D - O2 Sensor 2/1 Pumping Overcurrent.
23-028-162022-08-08. Service bulletin. EQUIPMENT; STRUCTURE. Rattle/Squeak From Rear Seat Armrest This bulletin involves inspecting the rear seat cushion frame for metal to metal contact, resulting in rattle noise. The customer may describe a rattle from the 60% portion of the rear seat. Metal to metal contact may be heard in either area.
08-039-16 REV. A2022-08-08. Service bulletin. POWER TRAIN; STEERING; ELECTRICAL SYSTEM; EXTERIOR LIGHTING. Transmission Wiring Harness Repair Or Replacement For No Start Or Stiff Steering This bulletin involves inspecting the transmission wire harness and installing mastic patch. If rub through is visible replace wire harness. A small number of customers may experience a no start condition, stiff steering or a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find the following Diagnostic Trouble Codes (DTCs): · U0131 - Lost Communication With Power Steering Control Module. · U0100-00 - Lost Communication With ECM/PCM. · P0512-00 - Starter Request Circuit.
08-028-172022-08-08. Service bulletin. EQUIPMENT:ELECTRICAL:RADIO/TAPE DECK/CD ETC.. RA3 And RA4 Radio Over The Air Software Updates This bulletin provides information regarding the latest Flash Over The Air update (FOTA) and provides a service technician an overview of the steps a customer will need to take to complete the update. The following improvements are included in this update: Adds Apple Siri® Eyes Free capability for iPhone® owners. Auto Play can now be configured. Adds do not disturb text message feature. The ability to drag and drop icons into the menu bar. Fix for radio locks up/frozen. Fix for stuck on black/blank screen. Human Machine Interface (HMI) improvements. Several navigation improvements. Fix for radio loses time. Charge Complete notification is not received (RU PHEV only). Media devices, Phone pairing and Bluetooth usage improvements. Improved tuner performance. Enhanced Voice recognition (VR) performance. Enhancements in Connectivity Apps (Yelp, Pandora, Aha, etc).
90036962022-08-08. Service bulletin. STRUCTURE:BODY:DOOR:HINGE AND ATTACHMENTS. Door Hinge Assembly Side door hinge noisy. Only replace the door hinge with the integral check device. Do not replace the simple hinge if it is not damaged it is not the source of the noise. Replacing it unnecessary and is an over-repair.
90036942022-08-08. Service bulletin. FUEL SYSTEM, GASOLINE. Oil Pump Assembly If error code P06DD present on any Pentastar V6 application, please inspect oil pump for relief valve failure. See photo attached. If valve is found out of place please call Bob Jackson (248) 944-0466 bob.jackson@fcagroup.com, or Joe Lovell (734) 309-6467 joe.lovell@fcagroup.com before proceeding. If unable to reach after 15 minutes record the following information and proceed with oil pump replacement and hold part for return to FCA via Fastrack system
08-019-17 REV. B2022-08-08. Service bulletin. AIR BAGS; BACK OVER PREVENTION; PARKING BRAKE; ELECTRICAL SYSTEM. RG3 RG4 RJ3 RJ4 Radio Enhancements This bulletin involves inspecting and if required, updating the radio software. A small number of customers may experience one or more of the following:Navigation failed message is displayed (WK and KL with RG3 and RG4). The clock not automatically updating to local time (WK and KL with RG3 and RG4). Poor or no connection to cellular network (WK and KL with RG3 and RG4). HVAC temperature out of sync with radio display (KL with RG3 and RG4). Some Uconnect App remote commands do not execute with the vehicle. Display goes blank/black (WK and KL with RG3 and RG4). Cyrillic keyboard is missing in phone book (WK and KL with RG3 or RG4). Wrong speed limit on NAV speed camera indication (WK and KL with RG3 or RG4). Blind Spot module beep or chime sound may be heard continuously (KL Only). Radio may keep the CAN bus network awake, causing a battery drain. Voice Recognition (VR) to set temperature, will indicate wrong setting to rear seat temperature. Not possible to set temperature in degrees Celsius using the VR (UK vehicles only). Teleprompter does not appear when pressing the VR button. VR operation cancels while in media mode. Radio may display camera?s previous image before displaying the current image. Navigation lost vehicle position during route calculation. Navigation displays are missing after vehicle heading changes. Navigation giving incorrect guidance to exit the highway. FM audio may switch to AM after ignition cycle. Text messages appear as sender?s phone number, not their name. VR phone button may not work at times. Audio muted after AUX device is disconnected. VR ?Listen? to text will only play first message. Drive Mode: Eco, Sport or Normal setting may not be saved after key cycle (LA, LD, LX and ZD Only). Drive Mode: Shift light On/Off, out of sync (LA, LD, LX and ZD Only). Speed adjusted volume may not work. AM/FM seek or tuner soft keys may be missing. Display screen shows ambient tempe
90038262022-08-08. Service bulletin. ENGINE AND ENGINE COOLING:COOLING SYSTEM:FAN. 2.4L KL Cooling fan If replacing the cooling fan for a P0480 -Cooling Fan 1 Control Circuit fault code or inoperative fan, please call Sam Zarnegar at (248) 944-5703 prior to removing any parts. If there is no response within 15 minutes, please leave a voicemail, or send an email to Sam.Zarnegar@fcagroup.com and continue with repair. Please include the VIN of the vehicle in all communication. Please return removed parts to FCA QEC for further analysis.
08-099-152022-08-08. Service bulletin. FUEL SYSTEM, GASOLINE. Incorrect Instrument Cluster Displays This Bulletin involves updating or replacing the Instrument Panel Cluster (IPC). A small number of customers may experience one or more of the following symptoms: ? Wrong language translations discovered ? Street names are being hyphenated incorrectly ? Fuel tank range till empty is to high The following software enhancements are also included in this software update. ? ECE market tire inflation value removed.
18-005-15 REV. E2022-08-08. Service bulletin. EXTERIOR LIGHTING; ENGINE AND ENGINE COOLING; ELECTRICAL SYSTEM. Flash: 2.4L Powertrain Diagnostic And System Improvements This bulletin involves reprogramming the Powertrain Control Module (PCM) with the latest available software. A small number of customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the Technician may find one or more of the following Diagnostic Trouble Codes (DTCs). 2015 KL Only ? U0402 - Implausible Data Received From TCM (ED6). ? P0116 - Engine Coolant Temperature Sensor 1 Performance. ? P050D - Cold Start Rough Idle. ? P2172 - High Airflow/Vacuum Leak Detected. ? P219A - Air-Fuel Ratio Cylinder Imbalance Bank 1 has been set in the PCM. 2014 KL Only ? P2172 - High Airflow/Vacuum Leak Detected. ? P219A - Air-Fuel Ratio Cylinder Imbalance Bank 1 has been set in the PCM. ? P106A - Cylinder 3 Oil Supply Solenoid Valve Switch Off Time Out Of Range. ? P2251 - O2 Sensor 1/1 Negative Current Control Circuit Open. ? P0031 - O2 Sensor 1/1 Heater Circuit Low. In addition, some customers may experience one or more of the following conditions. These conditions apply to 2015 model year vehicles only. ? Cold Engine Startup Flare and Idle Surge (ED6). ? Intermittent elevated engine RPM at start up. ? Less than desired gear engagement in lower ambient temperatures. ? Less than desired idle performance.
08-097-152022-08-08. Service bulletin. ELECTRICAL SYSTEM. FLASH: ABS Module Enhancements This bulletin involves updating the ABS Module software. New software is available to optimize Advanced Brake Assist (ABA) performance in low tractions situations.
21-053-152022-08-08. Service bulletin. POWER TRAIN. 948TE 9 Speed Transmission Quick Learn Procedure This bulletin provides information on how to perform the new scan tool based transmission Quick Learn procedure. This procedure is required after certain transmission repairs or to improve a customer?s concern of poor shift quality. Customers may indicate that their transmission shift quality may be erratic.
21-021-15 REV. E2022-08-08. Service bulletin. BACK OVER PREVENTION; EXTERIOR LIGHTING; ELECTRICAL SYSTEM; POWER TRAIN. Flash: Transmission Diagnostic And Shift Enhancements This bulletin involves reprogramming the Transmission Control Module (TCM) with the latest available software. A small number of customers may experience a Malfunction Indicator Lamp (MIL) illumination and/or one of the following conditions. Upon further investigation, a technician may find one or more of the following Diagnostic Trouble Codes (DTCs) stored in the TCM memory. 2015 KL Vehicles ? When driving on grades, the 3-2 downshift is hard to achieve or not available (ED6). ? P0711-00 - Transmission Fluid Temperature Sensor A Circuit Range-Performance (ED6). ? P0887-00 - TCM Power Control Circuit High. ? U0401-00 - Implausible Data Received From ECM/PCM. ? P1DAD-00 - Input Shaft-Output Shaft Direction Correlation. 2015 UF Vehicles ? When driving on grades, the 3-2 downshift is hard to achieve or not available (ED6). ? P0711-00 - Transmission Fluid Temperature Sensor A Circuit Range-Performance (ED6). ? P0885-00 - TCM Power Control Circuit (ED6). ? P0975-00 - Shift Solenoid B Control Circuit Performance (ED6). ? P0887-00 - TCM Power Control Circuit High (ED6). ? P0978-00 - Shift Solenoid 3 Control Circuit Performance (ED6). ? P0981-00 - Shift Solenoid 4 Control Circuit Performance (ED6). ? P0984-00 - Shift Solenoid 5 Control Circuit Performance (ED6). ? P1634-00 - TCM Internal Watchdog Performance (ERB). ? U0401-00 - Implausible Data Received From ECM/PCM. ? P1DAD-00 - Input Shaft-Output Shaft Direction Correlation. ? Garage shift improvements. Any shifting combination into or out of, Park, Drive, Reverse or Neutral (shifting at little or no vehicle speed). ? Up shift improvements, 2-3, 3-4 or 4-5 (ERB). This TCM calibration update being released also enables the new wiTECH based ?Transmission Quick Learn? procedure to be performed anytime the transmission adaptation memory cells are cleared or when addressing customer concerns of poor shift quality. It is also being rel
RL317270A$2022-08-08. Service bulletin. ELECTRICAL SYSTEM; POWER TRAIN. Part Description: 2014 KL 9-Speed service transaxle with 2015 common hardware Issue Description: This 9-speed transaxle must ordered thru Mopar?s Powertrain Service Center (PSC) for a specific VIN and must be installed in that vehicle or the correct calibration will not load to the Engine Control Module (ECM) and Transmission Control Module (TCM). This 9-speed transaxle assembly requires an update to the Engine Control Module AND the Transmission Control Module using WiTech. Failure to complete both updates will result in possible damage and/or incorrect operation of this unit.
5XN09DX9A$2022-08-08. Service bulletin. SEATS; EQUIPMENT. Part Description: Front seat trim covers Issue Description: For vehicles built prior to 7/13/2015, if the customer complaint is related to a hard spot or wear mark at the rear/center location of the front seat cushion cover, replace the heated seat element with a minimum AE level part. Remove adhered element with care to avoid damage to cushion foam pad. If replacement of the passenger cushion foam pad is necessary, The Occupant Detection System (ODS) module and foam pad must be ordered and replaced as a paired assembly. Not to be replaced independently.
08-019-17 REV. B2022-07-25. Service bulletin. AIR BAGS; BACK OVER PREVENTION; PARKING BRAKE; ELECTRICAL SYSTEM. RG3 RG4 RJ3 RJ4 Radio Enhancements This bulletin involves inspecting and if required, updating the radio software. A small number of customers may experience one or more of the following: Navigation failed message is displayed (WK and KL with RG3 and RG4). The clock not automatically updating to local time (WK and KL with RG3 and RG4). Poor or no connection to cellular network (WK and KL with RG3 and RG4). HVAC temperature out of sync with radio display (KL with RG3 and RG4). Some Uconnect App remote commands do not execute with the vehicle. Display goes blank/black (WK and KL with RG3 and RG4). Cyrillic keyboard is missing in phone book (WK and KL with RG3 or RG4). Wrong speed limit on NAV speed camera indication (WK and KL with RG3 or RG4). Blind Spot module beep or chime sound may be heard continuously (KL Only). Radio may keep the CAN bus network awake, causing a battery drain. Voice Recognition (VR) to set temperature, will indicate wrong setting to rear seat temperature. Not possible to set temperature in degrees Celsius using the VR (UK vehicles only). Teleprompter does not appear when pressing the VR button. VR operation cancels while in media mode. Radio may display camera?s previous image before displaying the current image. Navigation lost vehicle position during route calculation. Navigation displays are missing after vehicle heading changes. Navigation giving incorrect guidance to exit the highway. FM audio may switch to AM after ignition cycle. Text messages appear as sender?s phone number, not their name. VR phone button may not work at times. Audio muted after AUX device is disconnected. VR ?Listen? to text will only play first message. Drive Mode: Eco, Sport or Normal setting may not be saved after key cycle (LA, LD, LX and ZD Only). Drive Mode: Shift light On/Off, out of sync (LA, LD, LX and ZD Only). Speed adjusted volume may not work. AM/FM seek or tuner soft keys may be missing. Display screen shows ambient temperature as ?- - ? not n
90038262022-07-25. Service bulletin. EQUIPMENT; ENGINE AND ENGINE COOLING:COOLING SYSTEM:FAN. 2.4L KL Cooling fan If replacing the cooling fan for a P0480 -Cooling Fan 1 Control Circuit fault code or inoperative fan, please call Sam Zarnegar at (248) 944-5703 prior to removing any parts. If there is no response within 15 minutes, please leave a voicemail, or send an email to Sam.Zarnegar@fcagroup.com and continue with repair. Please include the VIN of the vehicle in all communication. Please return removed parts to FCA QEC for further analysis.
08-099-152022-07-25. Service bulletin. FUEL SYSTEM, GASOLINE. Incorrect Instrument Cluster Displays This Bulletin involves updating or replacing the Instrument Panel Cluster (IPC). A small number of customers may experience one or more of the following symptoms: ? Wrong language translations discovered ? Street names are being hyphenated incorrectly ? Fuel tank range till empty is to high The following software enhancements are also included in this software update. ? ECE market tire inflation value removed.
18-005-15 REV. E2022-07-25. Service bulletin. POWER TRAIN:AUTOMATIC TRANSMISSION; EQUIPMENT; ENGINE AND ENGINE COOLING. Flash: 2.4L Powertrain Diagnostic And System Improvements This bulletin involves reprogramming the Powertrain Control Module (PCM) with the latest available software. A small number of customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the Technician may find one or more of the following Diagnostic Trouble Codes (DTCs). 2015 KL Only ? U0402 - Implausible Data Received From TCM (ED6). ? P0116 - Engine Coolant Temperature Sensor 1 Performance. ? P050D - Cold Start Rough Idle. ? P2172 - High Airflow/Vacuum Leak Detected. ? P219A - Air-Fuel Ratio Cylinder Imbalance Bank 1 has been set in the PCM. 2014 KL Only ? P2172 - High Airflow/Vacuum Leak Detected. ? P219A - Air-Fuel Ratio Cylinder Imbalance Bank 1 has been set in the PCM. ? P106A - Cylinder 3 Oil Supply Solenoid Valve Switch Off Time Out Of Range. ? P2251 - O2 Sensor 1/1 Negative Current Control Circuit Open. ? P0031 - O2 Sensor 1/1 Heater Circuit Low. In addition, some customers may experience one or more of the following conditions. These conditions apply to 2015 model year vehicles only. ? Cold Engine Startup Flare and Idle Surge (ED6). ? Intermittent elevated engine RPM at start up. ? Less than desired gear engagement in lower ambient temperatures. ? Less than desired idle performance.

The summaries are NHTSA's. Each bulletin's page links NHTSA's copy of the manufacturer's document.