WenmarOpen by Wenmar Pro

Service bulletins for the 2015 Jeep Cherokee

A bulletin is a manufacturer's communication to its dealers, as NHTSA indexes it. The summary is NHTSA's. The document is the manufacturer's: read it at NHTSA. A bulletin is not a recall, and listing a model year does not mean every vehicle of it is concerned.

613 on file from NHTSA, as of 2026-10-19.

By type

By component

By trouble code

Only bulletins with component: Engine are shown. Show all

Bulletins, newest first
21-002-152018-11-19. Service bulletin. POWER TRAIN; ENGINE; ELECTRICAL SYSTEM. Start Stop Feature Inoperative After Transmission Replacement This bulletin involves verifying the Transmission Control Module (TCM) calibration and if necessary, replacing the TCM. A small number of customers may come in with a concern that their Start/Stop feature is no longer functional. Upon further investigation, it may be noted that this condition started after a transmission replacement.
07-002-152018-11-19. Service bulletin. ENGINE. Idler Pulley Noise During Cold Start This bulletin involves replacing the idler pulley. The customer may describe a loud high frequency noise that happens within 20 seconds of engine startup and lasts about 90 seconds intermittently during a cold engine start, approximately 0 degrees C (32 degrees F) and below.
07-002-15 REV. A2018-09-24. Service bulletin. ENGINE. Idler Pulley Noise During Cold Start This bulletin involves replacing the idler pulley. The customer may describe a loud high frequency noise that happens within 20 seconds of engine startup and lasts about 90 seconds intermittently during a cold engine start, approximately 0 degrees C (32 degrees F) and below.
18-005-15 REV. B2018-09-24. Service bulletin. POWER TRAIN; ELECTRICAL SYSTEM; ENGINE AND ENGINE COOLING:ENGINE. Flash: 2.4L Powertrain Diagnostic And System Improvements This bulletin involves selectively erasing and reprogramming the Powertrain Control Module (PCM) with new software. A small number of customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the Technician may find one of the following Diagnostic Trouble Codes (DTCs). Additionally this PCM update includes the enhancements listed below. 2015 KL Vehicles equipped with a 2.4L engine (Sales Code ED6 or ED8) built on or before October 21, 2014 (MDH 1021XX). ? P2172 - High Airflow/Vacuum Leak Detected. ? P219A - Air-Fuel Ratio Cylinder Imbalance Bank 1 has been set in the PCM. ? Improved software to enable Transmission Control Module (TCM) quick learn enhancements once TCM is updated. 2014 KL Vehicles equipped with a 2.4L engine (Sales Code ED6). ? P2172 - High Airflow/Vacuum Leak Detected. ? P219A - Air-Fuel Ratio Cylinder Imbalance Bank 1 has been set in the PCM. ? P106A - Cylinder 3 Oil Supply Solenoid Valve Switch Off Time Out Of Range. ? P2251 - O2 Sensor 1/1 Negative Current Control Circuit Open. ? P0031 - O2 Sensor 1/1 Heater Circuit Low.
18-004-16 REV. A2018-06-18. Service bulletin. POWER TRAIN:AUTOMATIC TRANSMISSION; POWER TRAIN:AUTOMATIC TRANSMISSION:CONTROL MODULE (TCM/PCM/TECM); EQUIPMENT; ENGINE. Flash: 2.4L Powertrain Diagnostic And System Improvements This bulletin involves reprogramming the Powertrain Control Module (PCM) with the latest available software. Some customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find one or more of the following DTCs: 2015 KL Only · **P0335 - Crankshaft Position Sensor Circuit.** · P0456 - EVAP System Small Leak. · P0300 - Multiple Cylinder Misfire. · P0301 - Cylinder 1 Misfire. · P0302 - Cylinder 2 Misfire. · P0303 - Cylinder 3 Misfire. · P0304 - Cylinder 4 Misfire. · P2610 - PCM Internal Engine Off Timer Performance. · P1607 - PCM Internal Shutdown Timer Rationality. · U0402 - Implausible Data Received From TCM (ED6). · P0116 - Engine Coolant Temperature Sensor 1 Performance. · P050D - Cold Start Rough Idle. · P2172 - High Airflow/Vacuum Leak Detected. · P219A - Air-Fuel Ratio Cylinder Imbalance Bank 1 has been set in the PCM. 2014 KL Only · P2172 - High Airflow/Vacuum Leak Detected. · P219A - Air-Fuel Ratio Cylinder Imbalance Bank 1 has been set in the PCM. · P106A - Cylinder 3 Oil Supply Solenoid Valve Switch Off Time Out Of Range. · P2251 - O2 Sensor 1/1 Negative Current Control Circuit Open. · P0031 - O2 Sensor 1/1 Heater Circuit Low. In addition, some customers may experience one or more of the following conditions: · Cold Engine Startup Flare and Idle Surge (ED6). · Intermittent elevated engine RPM at start up. · Less than desired gear engagement in lower ambient temperatures. · Less than desired idle performance.
05047457A2018-06-11. Service bulletin. ENGINE AND ENGINE COOLING. Multi-Air Actuator Assembly For 2.4 Tigershark Engine ONLY: When attempting to diagnose P Codes related to the MultiAir Unit, please note that there are multiple causes listed for each in the diagnostic procedure. This procedure must be followed to ensure the correct condition is being addressed. ~ Please verify the following (as listed in the first step in diagnostics) is not present before attempting repair:~ - Low Engine Oil - Incorrect oil filter that does not meet OEM specifications - Oil Dirty or Deteriorated (Lack of scheduled oil changes) - Incorrect Oil Viscosity/Weight - Engine Oil Contaminated (i.e. coolant and/or fuel) - Clogged Oil Galley Screen/Filter (top of block - feeds Multi-Air Unit) If there are any questions please contact: Seth Nankee at cell: (248) 303-5434 seth.nankee@fcagroup.com If no response within 15 minutes, please continue with diagnostics/repair.
18-035-162018-06-11. Service bulletin. ENGINE AND ENGINE COOLING; POWER TRAIN; ELECTRICAL SYSTEM. Flash: Powertrain Diagnostic And System Improvements This bulletin involves reprogramming the Powertrain Control Module (PCM) with the latest available software. A small number of customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation, the technician may find the following Diagnostic Trouble Codes (DTCs) set in the PCM memory: · **P1D83 - Implausible Engine Oil Temperature Signal Received.** · P0456 - EVAP System Small Leak. · P0335 - Crankshaft Position Sensor Circuit. · U0402 - Implausible Data Received From TCM - (Transmission Control Module).** · B10EA - Blower Motor Control Circuit High. · B10E9 - Blower Motor Control Circuit Low. · P0441 - EVAP Purge System Performance. · P0116 - Engine Coolant Temperature Sensor Performance. · P2067 - Fuel Level Sensor 2 Circuit Low (International Only). In addition the customer may notice one of the following conditions: · **A push sensation when the transmission is downshifting from eighth to seventh gear.** · Vehicle shudder at stop/start with A/C on.
18-068-162018-06-11. Service bulletin. ENGINE AND ENGINE COOLING. MIL Illumination: DTCs P112C and/or P112D This bulletin involves replacing the Post Catalyst Position O2 Sensor. A small number of customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find the following Diagnostic Trouble Codes (DTCs) stored or active: · P112C - O2 Sensor 2/1 Pumping Undercurrent. · P112D - O2 Sensor 2/1 Pumping Overcurrent.
90036942018-06-11. Service bulletin. ENGINE AND ENGINE COOLING. Oil Pump Assembly If error code P06DD present on any Pentastar V6 application, please inspect oil pump for relief valve failure. See photo attached. If valve is found out of place please call Bob Jackson (248) 944-0466 bob.jackson@fcagroup.com, or Joe Lovell (734) 309-6467 joe.lovell@fcagroup.com before proceeding. If unable to reach after 15 minutes record the following information and proceed with oil pump replacement and hold part for return to FCA via Fastrack system
68105583A2018-06-11. Service bulletin. ENGINE AND ENGINE COOLING. Pentastar Oil Filter Adapter: Before replacing this part, please call any one of the following people. Engineering is seeking information regarding this part.~ Dye must be used to determine where the leak is coming from before replacing. Also please check the recently updated Service Bulletin Number 09-008-15. ~ First: Nick Morand Cell (248) 410-8078 - Nick.morand@fcagroup.com Second: Bob Jackson Cell (248) 944-0466 - bob.jackson@fcagroup.com Third: Joe Lovell Cell (734 309-6467 - joe.lovell@fcagroup.com If a response is not received within 15 mins, then proceed with the necessary repair.~
08-094-142018-06-11. Service bulletin. STEERING; ENGINE AND ENGINE COOLING. Engine Does Not Start at The First Attempt This bulletin involves upgrading the software in the Electronic Steering Lock (ESL). The customer may experience where the engine fails to start at the first attempt. Initial cranking is inhibited but able to start/crank on the second attempt. On further inspection the technician may find DTC B1A92-09- ?Steering Lock Motor - Component Failures? stored in the ESL Module.
18-055-142018-06-11. Service bulletin. POWER TRAIN; ENGINE AND ENGINE COOLING. Flash: Malfunction Indicator Lamp (MIL) Illumination, P06EF-Engine Restart Performance This bulletin involves reprogramming the Powertrain Control Module (PCM) with new software. The customer may experience that the vehicle may not auto-start after the first auto-stop. This condition may occur if someone tried to start the vehicle with the engine already running. The vehicle will restart if the ignition is cycled off and than back on. A MIL lamp may turn on and a message ?Service start/stop? may be displayed. On further inspection DTC P06EF-Engine Restart Performance, may be found.
09-006-142018-06-11. Service bulletin. ENGINE AND ENGINE COOLING. Blue Smoke At Start Up This bulletin involves replacing the cylinder head, if required. Customers may notice blue smoke coming from the tail pipe at start up.
09-005-142018-06-11. Service bulletin. ENGINE AND ENGINE COOLING. Replace Engine Drive Belt This bulletin involves replacing the engine serpentine belt. The engine drive belt may exhibit a noise.
23-015-162018-06-04. Service bulletin. ENGINE AND ENGINE COOLING; STRUCTURE:BODY. Water On Front Carpet Or In Rocker Side Sill This bulletin involves visually inspecting the sealer on the engine bulkhead area and water testing to diagnose leak path. Then repairing body seam leaks with sealer. The customer may describe damp or wet carpet in the front footwell or in the rocker sill. This condition is primarily found on the left side but may be on the right (Fig. 1) or both footwells. The cause of this leak may be due to a sealant void on the body seam, allowing water to enter the vehicle interior.
23-015-16 REV. A2018-06-04. Service bulletin. ENGINE AND ENGINE COOLING; EQUIPMENT; STRUCTURE. Water On Front Carpet Or In Rocker Side Sill This bulletin involves visually inspecting the sealer on the engine bulkhead area and water testing to diagnose leak path. Then repairing body seam leaks with sealer. The customer may describe damp or wet carpet in the front footwell or in the rocker sill. This condition is primarily found on the left side but may be on the right (Fig. 1) or both footwells. The cause of this leak may be due to a sealant void on the body seam, allowing water to enter the vehicle interior.
RL108213A$2017-11-03. Service bulletin. ENGINE AND ENGINE COOLING. NAG1 (5A580) Valve Body As per Warranty Bulletin D-13-22, please use R2108213A$ valve body for all Warranty (W), Mopar (M) and Mopar Vehicle Protection (F) claims.~ Assembly also includes Filter (52108325AA) and Gasket (52108332AA).~
18-085-172017-11-03. Service bulletin. POWER TRAIN; ENGINE AND ENGINE COOLING; ELECTRICAL SYSTEM. Flash: Powertrain Diagnostic and System Improvements This bulletin involves reprogramming the Powertrain Control Module (PCM) with the latest available software. A small number of customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation, the technician may find the following DTCs set in the PCM memory:P1D83 - Implausible Engine Oil Temperature Signal Received (Software has been updated to better address this DTC). U1504 - Implausible Message Data Length Received From Steering Angle Sensor. U1424 - Implausible Engine Torque Signal Received. P0456 - EVAP System Small Leak. P0335 - Crankshaft Position Sensor Circuit. U0402 - Implausible Data Received From TCM - (Transmission Control Module). B10EA - Blower Motor Control Circuit High. B10E9 - Blower Motor Control Circuit Low. P0441 - EVAP Purge System Performance. P0116 - Engine Coolant Temperature Sensor Performance. P2067 - Fuel Level Sensor 2 Circuit Low (International Only). In addition the customer may notice one of the following conditions:A push/bump feeling when the transmission is downshifting from eighth to seventh gear. Vehicle shudder at stop/start with A/C on. Software enhancement also includes:Calibration update to allow the throttle body to be cycled while the engine is off, for diagnostic purposes.
90033552017-11-03. Service bulletin. ENGINE AND ENGINE COOLING. 3.2L - 3.6L Cylinder Head Assy Multiple cylinder head replacement. If a cylinder head is replaced on a vehicle more than 1 time for any reason, please call any of the following people. First: Joe Lovell - Cell (734) 309-6467 joe.lovell@fcagroup.com Second: Kevin Refalo - Cell (248) 260-0738 Kevin.refalo@facgroup.com If no response in 15 minutes, proceed with repair.
68103198A$2017-11-03. Service bulletin. ENGINE AND ENGINE COOLING. A/C Compressor This applies to 2015 and 2016 KL, UF and PF. Before replacing the AC compressor for noise, leaks , or for an inop condition:~ After these questions have been answered please call one of the individuals below.~ 1) Check all AC plumbing connection for leaks with UV light. Any leaks found?~ 2) Does compressor pulley and clutch hub turn freely, or are they seized?~ 3) What was the amount of the recovered refrigerant?~ After these questions have been answered please call one of the individuals below:~ Stev at cell (248) 867-0061~ Mark Briolat at cell (248) 345-0127~ If no response in 15 minutes, please continue with repair.~ If the compressor is replaced, then:~ 4) Drain oil from compressor. What was quantity of oil recovered?
18-007-16 REV. A2017-10-21. Service bulletin. ENGINE; ELECTRICAL SYSTEM. Flash: 2.4L Powertrain Diagnostic And System Improvements This bulletin involves reprogramming the Powertrain Control Module (PCM) with the latest available software. Some customers may experience an engine stop start failure while driving. The customer may describe that when the brake pedal is released immediately after the vehicle enters Electronic Start Stop Mode (ESS), the engine turns off and wont restart until you shift to park and cycle the key.
18-068-162016-09-14. Service bulletin. ELECTRICAL SYSTEM; ENGINE. " MIL ILLUMINATION: DTCS P112C AND/OR P112D THIS BULLETIN INVOLVES REPLACING THE POST CATALYST POSITION O2 SENSOR. A SMALL NUMBER OF CUSTOMERS MAY EXPERIENCE A MALFUNCTION INDICATOR LAMP (MIL) ILLUMINATION. UPON FURTHER INVESTIGATION THE TECHNICIAN MAY FIND THE FOLLOWING DIAGNOSTIC TROUBLE CODES (DTCS) STORED OR ACTIVE: · P112C - O2 SENSOR 2/1 PUMPING UNDERCURRENT. · P112D - O2 SENSOR 2/1 PUMPING OVERCURRENT. "
09-006-142016-04-26. Service bulletin. ENGINE. SUMMARY TO BE PROVIDED ON A FUTURE DATE.
09-005-142016-04-26. Service bulletin. ENGINE. SUMMARY TO BE PROVIDED ON A FUTURE DATE.
09-005-14REV.A2016-04-26. Service bulletin. ENGINE. SUMMARY TO BE PROVIDED ON A FUTURE DATE.

The summaries are NHTSA's. Each bulletin's page links NHTSA's copy of the manufacturer's document.