Service bulletins for the 2014 Jeep Cherokee
A bulletin is a manufacturer's communication to its dealers, as NHTSA indexes it. The summary is NHTSA's. The document is the manufacturer's: read it at NHTSA. A bulletin is not a recall, and listing a model year does not mean every vehicle of it is concerned.
563 on file from NHTSA, as of 2026-10-19.
By type
By component
By trouble code
Only bulletins with component: Transmission and driveline are shown. Show all
| S1721000016 | 2022-10-17. Service bulletin. POWER TRAIN. Service 4wd Light On, Message AWD System Service Required |
|---|---|
| 2101721 | 2022-10-17. Service bulletin. BACK OVER PREVENTION; WHEELS; POWER TRAIN:TRANSFER CASE (4-WHEEL DRIVE); EXTERIOR LIGHTING. Power Transfer Unit (PTU) Broken Input Spline - X89 Warranty Extension This bulletin involves replacing the PTU assembly with an updated part. Customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find that one or more of the following Diagnostic Trouble Codes (DTCs) have been set: P1720-00 - Output Speed Sensor-Wheel Speed Rationality. P215C-00 - Output Shaft Speed Wheel Speed Correlation. The customer may also describe one or more of the following: Grinding noise coming from under the vehicle while driving. Vehicle will not move. |
| 2101721RevA | 2022-10-17. Service bulletin. EXTERIOR LIGHTING; BACK OVER PREVENTION; WHEELS; POWER TRAIN:TRANSMISSION CASE/HOUSING; POWER TRAIN:TRANSFER CASE (4-WHEEL DRIVE). Power Transfer Unit (PTU) Broken Input Spline - X89 Warranty Extension This bulletin involves replacing the PTU assembly with an updated part. Customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find that one or more of the following Diagnostic Trouble Codes (DTCs) have been set: P1720-00 - Output Speed Sensor-Wheel Speed Rationality. P215C-00 - Output Shaft Speed Wheel Speed Correlation. The customer may also describe one or more of the following:Grinding noise coming from under the vehicle while driving. Vehicle will not move. |
| 74595 | 2022-10-17. Service bulletin. POWER TRAIN:AUTOMATIC TRANSMISSION; POWER TRAIN. Warranty Bulletin D-21-07 (X89) Power Transfer Unit - 2014-2017 Jeep Cherokee (KL) |
| 2101721 | 2022-10-17. Service bulletin. POWER TRAIN; ELECTRICAL SYSTEM. Power Transfer Unit (PTU) Broken Input Spline - X89 Warranty Extension This bulletin involves replacing the PTU assembly with an updated part. Customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find that one or more of the following Diagnostic Trouble Codes (DTCs) have been set: P1720-00 - Output Speed Sensor-Wheel Speed Rationality. P215C-00 - Output Shaft Speed Wheel Speed Correlation. The customer may also describe one or more of the following: Grinding noise coming from under the vehicle while driving. Vehicle will not move. |
| 2101721REVA | 2022-10-17. Service bulletin. POWER TRAIN. Power Transfer Unit (PTU) Broken Input Spline - X89 Warranty Extension This bulletin involves replacing the PTU assembly with an updated part. Customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find that one or more of the following Diagnostic Trouble Codes (DTCs) have been set: P1720-00 - Output Speed Sensor-Wheel Speed Rationality. P215C-00 - Output Shaft Speed Wheel Speed Correlation. The customer may also describe one or more of the following:Grinding noise coming from under the vehicle while driving. Vehicle will not move. |
| 74595 | 2022-10-17. Service bulletin. POWER TRAIN. Warranty Bulletin D-21-07 (X89) Power Transfer Unit - 2014-2017 Jeep Cherokee (KL) |
| CSNW20 | 2022-10-17. Service bulletin. POWER TRAIN. Customer Satisfaction Notification W20 Reprogram Powertrain Control Module |
| W84 | 2022-09-26. Service bulletin. POWER TRAIN; ELECTRICAL SYSTEM. Customer Satisfaction Notification W84 Powertrain Software Update |
| 08-013-15 | 2022-09-26. Service bulletin. VEHICLE SPEED CONTROL; STEERING; AIR BAGS; SEAT BELTS; STRUCTURE; POWER TRAIN; ELECTRICAL SYSTEM. Flash: BCM Diagnostic And System Improvements This bulletin involves updating the Body Control Module (BCM) software. Customer and or Technician may notice one of more of the following: ? A message may be displayed in the cluster ?Start/Stop Not Available?, this may have started after the battery was disconnected. On Further inspection the Technician may find DTC U0216 Lost Communication With Driver Door Switch. ? Intermittent No Start condition Without any DTCs (Vehicles with steering column lock, only). ? U1220-87 - Lost Steering Lock Request Message - Missing Message. ? U1517-87 - Body Controller Secret Code - Missing Message. ? B2199-17 - Battery Voltage - Circuit Voltage Above Threshold, set in the BCM. ? Day Time Running Lamps (DRL) will not turn on until the vehicle speed is 2 MPH (3 KPH), (Manual Transmission only). ? Puddle Lamps will not turn off when the engine is started, (Manual Transmission only). NOTE: If battery system DTC P0562 Battery/System Voltage Low or P0563 Battery/System Voltage High are set, normal charging system diagnostics needs to be performed. |
| 21-008-15 | 2022-09-26. Service bulletin. POWER TRAIN. Transmission Shift Quality C-Clutch Snap Ring This bulletin involves removing the transmission, disassembling, and replacing the C-Clutch snap ring. A small number of customers may experience less than desired shift quality during a 5-4 downshift and/or Malfunction Indicator Lamp (MIL) Illumination. Upon further inspection, the technician may find Diagnostic Trouble Code (DTC) U0402 setting in the Powertrain Control Module (PCM) memory. |
| W84 | 2022-09-26. Service bulletin. POWER TRAIN. Customer Satisfaction Notification W84 Powertrain Software Update |
| W20 | 2022-09-26. Service bulletin. POWER TRAIN. Customer Satisfaction Notification W20 Reprogram Powertrain Control Module |
| S1821000001 | 2022-09-26. Service bulletin. POWER TRAIN. Gear Ratio DTC?s, Transmission Shift Concerns, Does Not Shift At Times, Shudders |
| 9004009 | 2022-09-26. Service bulletin. POWER TRAIN. Transmission Kit with Torque Converter 1. All Promaster (VF) 3.6L/62TE equipped vehicles. If the transmission bracket to the transmission case fasteners are removed during servicing, the fasteners (Part Number 06511385A$) are one-time usage. Vehicles built prior to 10/23/2015 requires Service Kit PN 68461214AA; includes Transmission Isolator PN 68264483AA, and Adaptation Bracket 68264479AA and Fastener Service Kit PN 68329056AA Vehicles built after on or after 10/23/2015 will require only the Fastener Service Kit PN 68329056AA. 2. All 3.6L/62TE equipped vehicles. If the vehicle you are repairing has a crack in the flex plate or failed pump bushing inspect and confirm that both (2) dowel pins are present in the engine block, which align the transmission center line to the crank shaft centerline and visually inspect the dowel alignment holes in the transmission case. If the holes are damaged or elongated the transmission should be replaced to prevent further damage to the transmission/flexplate or pump bushing due to the inability to properly align the engine to the transmission during the repair. 3. All 62TE equipped vehicles. If pump bushing is scored or damaged and the dowel pin alignment holes are ok, replace the pump assembly as opposed to complete transmission. 4. All 62TE equipped vehicles. If vehicle is jerking/slipping with MIL code(s) P0740 or P2764, check TCC Solenoid operation. If TCC Solenoid is ok, the codes are indicative of a torque converter failure. Replace the torque converter. |
| 0811114 | 2022-09-26. Service bulletin. POWER TRAIN; ELECTRICAL SYSTEM; VEHICLE SPEED CONTROL; SEAT BELTS; AIR BAGS; STRUCTURE; STEERING. Flash: BCM Diagnostic And System Improvements This bulletin involves updating the Body Control Module (BCM) software. Customer and or Technician may notice one of more of the following: A message may be displayed in the cluster ?Start/Stop Not Available?, this may have started after the battery was disconnected. On Further inspection the Technician may find DTC U0216 Lost Communication With Driver Door Switch. Without any DTCs (Vehicles with steering column lock, only). U1220-87 - Lost Steering Lock Request Message - Missing Message. U1517-87 - Body Controller Secret Code - Missing Message. B2199-17 - Battery Voltage - Circuit Voltage Above Threshold, set in the BCM. Day Time Running Lamps (DRL) will not turn on until the vehicle speed is 2 MPH (3 KPH), (Manual Transmission only). Puddle Lamps will not turn off when the engine is started, (Manual Transmission only).If battery system DTC P0562 Battery/System Voltage Low or P0563 Battery/System Voltage High are set, normal charging system diagnostics needs to be performed. |
| 1806014REVC | 2022-09-26. Service bulletin. EXTERIOR LIGHTING; POWER TRAIN; ELECTRICAL SYSTEM; BACK OVER PREVENTION. Flash: Diagnostic And System Improvements This bulletin involves selectively erasing and reprogramming the Powertrain Control Module (PCM) with new software. A small number of customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the Technician may find one of the following Diagnostic Trouble Codes (DTCs). Additionally this PCM update includes the enhancements listed below. 2015 KL Vehicles equipped with a 2.4L engine (Sales Code ED6 or ED8) built on or before October 21, 2014 (MDH 1021XX). ? P2172 - High Airflow/Vacuum Leak Detected. ? Improved software to enable Transmission Control Module (TCM) quick learn enhancements once TCM is updated. 2015 KL Vehicles equipped with a 3.2L engine (Sales Code EHB) built on or before November 20, 2014 (MDH 1120XX). ? P2067- Fuel Level Sensor 2 Circuit Low (International Only). ? Improved software to enable Transmission Control Module (TCM) quick learn enhancements once TCM is updated. 2014 KL Vehicles equipped with a 2.4L engine (Sales Code ED6). ? P219A - Air-Fuel Ratio Cylinder Imbalance Bank 1 has been set in the PCM. ? P106A - Cylinder 3 Oil Supply Solenoid Valve Switch Off Time Out Of Range. |
| 2101814REVB | 2022-09-26. Service bulletin. ELECTRICAL SYSTEM; POWER TRAIN. Flash: Transmission Shift and Diagnostic Enhancements This bulletin involves flash reprogramming of the Transmission Control Module (TCM) with new software.Vehicles that are being updated from TCM software p/n 682235$$AN or 682354$$AN ($$ are wild cards for any number) will not require the 9 Speed Adaptation Drive Learn Procedure to be performed. However, vehicles being updated from any other software part number will require the Adaptation Drive Learn Procedure to be performed. Refer to all applicable published service bulletins regarding the 9 Speed Adaptation Drive Learn procedure for detailed repair procedures and labor times. Diagnostic Trouble Code (DTC) robustness improvements are included in this software release. These improvements apply to the following DTCs: P072F- Stuck in Gear 4 P076F- Gear 7 shift incorrect ratio P0810- Clutch position control error P1CC9- Unable to engage gear P0734- Gear 4 shift incorrect ratio P061B- Internal control module torque calculation performance |
| 2100314REVA | 2022-09-26. Service bulletin. EXTERIOR LIGHTING; ELECTRICAL SYSTEM; POWER TRAIN; WHEELS. Flash: 845RE Transmission Shift Enhancements, 2-1 Downshift This bulletin involves reprogramming the Transmission Control Module (TCM) with the latest available software. The following TCM calibration improvements are available for vehicles equipped an 845RE Automatic Transmission (Sales Code DFL). These updates are listed by vehicle and engine.LD and LX vehicles equipped with a 3.6L engine (Sales Code ERB) Software to correct a harsh bump feel during a 2-1 downshift. Software to enable the scan tool based transmission ?Quick Learn.? Software to address customer concerns of Malfunction Indicator Lamp (MIL) illumination and Diagnostic Trouble Code (DTC) P215C Output Shaft Speed, Wheel Speed Correlation setting on AWD equipped vehicles.LX and WK vehicles equipped with a 3.0L engine (Sales Code EHD) Software to correct a harsh bump feel during a 2-1 downshift.WK vehicles equipped with a 3.6L engine (Sales Code ERB) Software to correct a harsh bump feel during a 2-1 downshift.DS vehicles equipped with 3.6L engine (Sales Code ERB) |
| 2102714 | 2022-09-26. Service bulletin. POWER TRAIN; ELECTRICAL SYSTEM; AIR BAGS. Flash: MIL Illumination For P0733, P061B, P1DB8 This bulletin involves selectively erasing and reprogramming the Transmission Control Module (TCM) with new software. The following Transmission Control Module (TCM) calibration improvements are available. ? P0733 Gear 3 Shift Incorrect Ratio ? P061B Internal Control Module Torque Calculation Performance ? P1DB8 Due to erroneous DTC ? Improved downshift response in Adaptive Cruise Control (ACC) operation when there is a driver override. |
| 1803114 | 2022-09-26. Service bulletin. POWER TRAIN:AUTOMATIC TRANSMISSION:CONTROL MODULE (TCM/PCM/TECM); FUEL SYSTEM, GASOLINE; ELECTRICAL SYSTEM. Flash: MIL Illumination P1239, P0298- Engine Oil Temperature Too Low Or High, P0300 Multiple Cylinder Misfire, Includes Powertrain System Improvements/Enhancements This bulletin involves selectively erasing and reprogramming the Powertrain Control Module (PCM) with new software. A small number of customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the Technician may find that the following Diagnostic Trouble Code has been set: P1239 - Engine Oil Temperature Too Low, set in cold ambient temperatures. P0298 - Engine Oil Temperature Too High, set in cold ambient temperatures. P0300 - Multiple Cylinder Misfire, may set at a 1-2 upshift above 6000 RPM. Possible rough idle when engaging Drive while in 4 LOW after a cold start .The following system improvements have also been included in this software release: Corrected a generic scan tool display issue regarding Mode 6 data accuracy. |
| W84 | 2022-09-26. Service bulletin. POWER TRAIN:AUTOMATIC TRANSMISSION:CONTROL MODULE:SOFTWARE. Customer Satisfaction Notification W84 Powertrain Software Update |
| 1UT661X9A | 2022-09-15. Service bulletin. EQUIPMENT; POWER TRAIN:AXLE ASSEMBLY:AXLE SHAFT. ATX Shifter Assembly Description: For KL ONLY: Before this part is replaced for any issue please call John Tache on cell (248) 841-6711. If you do not receive a return call within 15 minutes, proceed with the repair. Please be sure to accurately record any symptoms and DTCs identified with the scan tool and document them on the repair order. |
| D1607 | 2022-09-15. Service bulletin. SEATS; POWER TRAIN. To announce the removal of the 9-speed 948TE transmission from the Powertrain Pre-Authorization Program |
| 18-031-14 | 2022-08-29. Service bulletin. POWER TRAIN:AUTOMATIC TRANSMISSION; EXTERIOR LIGHTING. Flash: MIL Illumination P1239- Engine Oil Temperature Too Low. Includes Powertrain System Improvements/Enhancements This bulletin involves selectively erasing and reprogramming the Powertrain Control Module (PCM) with new software. A small number of customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the Technician may find that the following Diagnostic Trouble Code has been set: ? P1239 - Engine Oil Temperature Too Low The following system improvements have also been included in this software release: ? Corrected a generic scan tool display issue regarding Mode 6 data accuracy |
The summaries are NHTSA's. Each bulletin's page links NHTSA's copy of the manufacturer's document.