Service bulletins for the 2014 Jeep Cherokee
A bulletin is a manufacturer's communication to its dealers, as NHTSA indexes it. The summary is NHTSA's. The document is the manufacturer's: read it at NHTSA. A bulletin is not a recall, and listing a model year does not mean every vehicle of it is concerned.
563 on file from NHTSA, as of 2026-10-19.
By type
By component
By trouble code
Only bulletins with component: Electrical system are shown. Show all
| 9003029 | 2022-09-26. Service bulletin. ELECTRONIC STABILITY CONTROL:AUTOMATIC (ASC); BACK OVER PREVENTION; STEERING; WHEELS; SUSPENSION; ELECTRICAL SYSTEM. Part Description: Steering Column and Seals. Issue Description: If the customer complains of a steering column squeak when turning the wheel in low speed maneuvers (parking lot, driveway) in cold weather, the following inspection procedure will assist in preventing a misdiagnosis.~ Inspect the suspension front coil spring to isolators. This can be done by first letting the vehicle cold soak. The noise is normally heard in temperatures ranging from 15- 40 degrees (F). With one person in the vehicle turning the steering wheel, place your hand on the front spring. If a vibration is felt when the noise is heard by the vehicle occupant, the issue is from the front suspension ? not in the steering column. Do not service the steering column. |
|---|---|
| 9004386 | 2022-09-26. Service bulletin. ELECTRICAL SYSTEM:WIRING. WIRING, Body Before replacing this harness, please contact FCA Redacted Content to see if a repair kit is available for your application. If no response in 15 minutes, proceed with repair. Please email pictures of harness defects to FCA Redacted Content |
| S2008000113 | 2022-09-26. Service bulletin. ELECTRICAL SYSTEM. No Start Intermittently, Vehicle Requires Multiple Keyless Push To Start Attempts To Start Vehicle, Intermittent Key Not Detected Message |
| 0811114 | 2022-09-26. Service bulletin. POWER TRAIN; ELECTRICAL SYSTEM; VEHICLE SPEED CONTROL; SEAT BELTS; AIR BAGS; STRUCTURE; STEERING. Flash: BCM Diagnostic And System Improvements This bulletin involves updating the Body Control Module (BCM) software. Customer and or Technician may notice one of more of the following: A message may be displayed in the cluster ?Start/Stop Not Available?, this may have started after the battery was disconnected. On Further inspection the Technician may find DTC U0216 Lost Communication With Driver Door Switch. Without any DTCs (Vehicles with steering column lock, only). U1220-87 - Lost Steering Lock Request Message - Missing Message. U1517-87 - Body Controller Secret Code - Missing Message. B2199-17 - Battery Voltage - Circuit Voltage Above Threshold, set in the BCM. Day Time Running Lamps (DRL) will not turn on until the vehicle speed is 2 MPH (3 KPH), (Manual Transmission only). Puddle Lamps will not turn off when the engine is started, (Manual Transmission only).If battery system DTC P0562 Battery/System Voltage Low or P0563 Battery/System Voltage High are set, normal charging system diagnostics needs to be performed. |
| 1806014REVC | 2022-09-26. Service bulletin. EXTERIOR LIGHTING; POWER TRAIN; ELECTRICAL SYSTEM; BACK OVER PREVENTION. Flash: Diagnostic And System Improvements This bulletin involves selectively erasing and reprogramming the Powertrain Control Module (PCM) with new software. A small number of customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the Technician may find one of the following Diagnostic Trouble Codes (DTCs). Additionally this PCM update includes the enhancements listed below. 2015 KL Vehicles equipped with a 2.4L engine (Sales Code ED6 or ED8) built on or before October 21, 2014 (MDH 1021XX). ? P2172 - High Airflow/Vacuum Leak Detected. ? Improved software to enable Transmission Control Module (TCM) quick learn enhancements once TCM is updated. 2015 KL Vehicles equipped with a 3.2L engine (Sales Code EHB) built on or before November 20, 2014 (MDH 1120XX). ? P2067- Fuel Level Sensor 2 Circuit Low (International Only). ? Improved software to enable Transmission Control Module (TCM) quick learn enhancements once TCM is updated. 2014 KL Vehicles equipped with a 2.4L engine (Sales Code ED6). ? P219A - Air-Fuel Ratio Cylinder Imbalance Bank 1 has been set in the PCM. ? P106A - Cylinder 3 Oil Supply Solenoid Valve Switch Off Time Out Of Range. |
| 2101814REVB | 2022-09-26. Service bulletin. ELECTRICAL SYSTEM; POWER TRAIN. Flash: Transmission Shift and Diagnostic Enhancements This bulletin involves flash reprogramming of the Transmission Control Module (TCM) with new software.Vehicles that are being updated from TCM software p/n 682235$$AN or 682354$$AN ($$ are wild cards for any number) will not require the 9 Speed Adaptation Drive Learn Procedure to be performed. However, vehicles being updated from any other software part number will require the Adaptation Drive Learn Procedure to be performed. Refer to all applicable published service bulletins regarding the 9 Speed Adaptation Drive Learn procedure for detailed repair procedures and labor times. Diagnostic Trouble Code (DTC) robustness improvements are included in this software release. These improvements apply to the following DTCs: P072F- Stuck in Gear 4 P076F- Gear 7 shift incorrect ratio P0810- Clutch position control error P1CC9- Unable to engage gear P0734- Gear 4 shift incorrect ratio P061B- Internal control module torque calculation performance |
| 2100314REVA | 2022-09-26. Service bulletin. EXTERIOR LIGHTING; ELECTRICAL SYSTEM; POWER TRAIN; WHEELS. Flash: 845RE Transmission Shift Enhancements, 2-1 Downshift This bulletin involves reprogramming the Transmission Control Module (TCM) with the latest available software. The following TCM calibration improvements are available for vehicles equipped an 845RE Automatic Transmission (Sales Code DFL). These updates are listed by vehicle and engine.LD and LX vehicles equipped with a 3.6L engine (Sales Code ERB) Software to correct a harsh bump feel during a 2-1 downshift. Software to enable the scan tool based transmission ?Quick Learn.? Software to address customer concerns of Malfunction Indicator Lamp (MIL) illumination and Diagnostic Trouble Code (DTC) P215C Output Shaft Speed, Wheel Speed Correlation setting on AWD equipped vehicles.LX and WK vehicles equipped with a 3.0L engine (Sales Code EHD) Software to correct a harsh bump feel during a 2-1 downshift.WK vehicles equipped with a 3.6L engine (Sales Code ERB) Software to correct a harsh bump feel during a 2-1 downshift.DS vehicles equipped with 3.6L engine (Sales Code ERB) |
| 0808114 | 2022-09-26. Service bulletin. ELECTRICAL SYSTEM. MIL Illumination DTC U11E9 After Fascia Removal This bulletin involves confirming that the Active Grille Shutter (AGS) electrical harness connector is properly connected. |
| 0807714 | 2022-09-26. Service bulletin. EQUIPMENT:ELECTRICAL; ELECTRICAL SYSTEM:IGNITION:ANTI-THEFT:IMMOBILIZER/PROXIMITY:KEY/SENDER. Flash: Key Programming Improvements This bulletin involves updating the Radio Frequency HUB (RF HUB) with new software. The technician may have issues when trying to program new keys or installing Mopar remote start kits. Before programming keys make sure the RF HUB has the latest software in it. |
| 0807614 | 2022-09-26. Service bulletin. ELECTRICAL SYSTEM. Engine Does Not Start at the First Attempt This bulletin involves upgrading the software in the Powertrain Control Module (PCM). A customer may experience, the engine fails to start at the first attempt using the Keyless Ignition Node (KIN) button. |
| 2102714 | 2022-09-26. Service bulletin. POWER TRAIN; ELECTRICAL SYSTEM; AIR BAGS. Flash: MIL Illumination For P0733, P061B, P1DB8 This bulletin involves selectively erasing and reprogramming the Transmission Control Module (TCM) with new software. The following Transmission Control Module (TCM) calibration improvements are available. ? P0733 Gear 3 Shift Incorrect Ratio ? P061B Internal Control Module Torque Calculation Performance ? P1DB8 Due to erroneous DTC ? Improved downshift response in Adaptive Cruise Control (ACC) operation when there is a driver override. |
| 1803114 | 2022-09-26. Service bulletin. POWER TRAIN:AUTOMATIC TRANSMISSION:CONTROL MODULE (TCM/PCM/TECM); FUEL SYSTEM, GASOLINE; ELECTRICAL SYSTEM. Flash: MIL Illumination P1239, P0298- Engine Oil Temperature Too Low Or High, P0300 Multiple Cylinder Misfire, Includes Powertrain System Improvements/Enhancements This bulletin involves selectively erasing and reprogramming the Powertrain Control Module (PCM) with new software. A small number of customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the Technician may find that the following Diagnostic Trouble Code has been set: P1239 - Engine Oil Temperature Too Low, set in cold ambient temperatures. P0298 - Engine Oil Temperature Too High, set in cold ambient temperatures. P0300 - Multiple Cylinder Misfire, may set at a 1-2 upshift above 6000 RPM. Possible rough idle when engaging Drive while in 4 LOW after a cold start .The following system improvements have also been included in this software release: Corrected a generic scan tool display issue regarding Mode 6 data accuracy. |
| W20 | 2022-09-26. Service bulletin. ELECTRICAL SYSTEM. Customer Satisfaction Notification W20 Reprogram Powertrain Control Module (Revision 2) |
| 0806016 | 2022-09-26. Service bulletin. PARKING BRAKE; ELECTRICAL SYSTEM. Electronic parking brake module connector water intrusion. |
| 0811119 | 2022-09-15. Service bulletin. ELECTRICAL SYSTEM; EQUIPMENT. RA3 and RA4 GPS Radio Update This bulletin involves updating the radio software. 18.01.35 (BU Vehicles) |
| D1925 | 2022-09-15. Service bulletin. EQUIPMENT; ELECTRICAL SYSTEM. RRT 19-090 (Service Bulletin 08-111-19) 2013-2018 Multiple Vehicles RA3/RA4 Radio GPS Certification Error |
| 08-064-16 | 2022-09-15. Service bulletin. EXTERIOR LIGHTING:HEADLIGHTS; ELECTRICAL SYSTEM. Headlamp Leveling Switch Position Not Correct This bulletin involves running the wiTECH function: Configure BUX Headlamp Parameters. Customers may describe that the headlamp leveling switch positions are opposite of the actual headlamp positions (Fig. 1). For example, switch down position is headlamps up and vice versa. |
| 08-054-16 | 2022-09-15. Service bulletin. EQUIPMENT; ELECTRICAL SYSTEM; EQUIPMENT:ELECTRICAL:INFOTAINMENT. RA3 RA4 Radio Enhancements This bulletin involves inspecting and updating the radio software, if required. **Improvements: · Ability to communicate with Siri via UConnect. · Ability to press Voice Recognition (VR) button for more than one second.** A customer may experience one or more of the following conditions: · **Poor or no connection to cellular network (U.S. market only). · HVAC temperature out of sync with radio display (KL vehicles).** · Track names may be displayed twice in USB or SD media modes. · SD, USB or BTSA modes may become non-functional for a given ignition cycle. · Duplicate song titles may be displayed in USB mode. · Last track is displayed but next track is being played. · Navigation function may resets itself after using One-Shot VR. · Intermittently the Global Positioning System (GPS) may lose its location for a short time and causes routing and positioning concerns. · GPS and Internal cellular device may become inoperative and causes a loss of GPS and cellular functions. · A false Pop-up message may appear ?Vehicle Phone Requires Service? even though the vehicle?s phone works properly. · Back-up camera image may be unclear or jittery/stutters at times. · Enables Via Mobile software features when released to consumers (U.S. market only). · Able to adjust audio balance / fade settings during a VR session. · Correct condition where user could not exit screen off mode. · Mute button status was not being displayed correctly. · Presets where not shown correctly or were deleted. · Enhancements to POI. · ParkSense tone continuously on. · Radio display may shows ?Please insert USB Stick?. · Enhancement made when video is display in radio when using PAL format video disks. · Corrected the temperature slider bar not updating on Manual Temperature Control vehicles. · Navigation may not start or may lose position. · Rear camera may show a black screen for 3 seconds upon going to rev |
| 08-008-14 | 2022-08-29. Service bulletin. ELECTRICAL SYSTEM:SOFTWARE; EQUIPMENT:ELECTRICAL:RADIO/TAPE DECK/CD ETC.; UNKNOWN OR OTHER. RA2 RG2 Or RJ2 Radio Update To Prevent Display Screen Lockup This bulletin involves updating the radio's software or replacing the radio if required. A customer may experience the radio display screen is locked on the Ram logo. This software update is to prevent this condition from occurring. Vehicles equipped with satellite radio (sales code RSD) may have a condition were the radio may reset a few times during a drive cycle. This condition is very intermittent. |
| 9003081 | 2022-08-29. Service bulletin. ELECTRICAL SYSTEM. Dielectric Grease This product is no longer approved for use on ignition coil and spark plug boots. Current plug boot material(silicone) is not compatible with this grease and can cause deterioration over time. |
| 9004401 | 2022-08-22. Service bulletin. ELECTRONIC STABILITY CONTROL:AUTOMATIC (ASC); ELECTRICAL SYSTEM; SERVICE BRAKES, HYDRAULIC; BACK OVER PREVENTION; FUEL SYSTEM, GASOLINE. DIFFERENTIAL, Rear Axle (KL 4WD w/DK2 = 1-SPEED RDM) The Differential, Rear Axle (aka RDM) design, pump design, Driveline Control Module (aka DLCM) hardware & software and pressure sensor have all changed in the past few years. The changes are not interchangeable and each had a separate implementation date. Please comprehend it to avoid repeat repairs. There are 2 sections each with 3 sub-sections: 1) For 2014/5 VINs with DK2 = 1-spd RDM 2) For 2016 and later VINs with DK2 = 1-spd RDM 1) For 2014/5 VINs with DK2 = 1-spd RDM 2014 - 2015 VINs were built with a 1-speed RDM used a 24 plate clutch design. New service RDMs 68550586A$ use a 20-plate design. 1.1) If replacing the RDM · 24 plate and 20-plate design RDMs are NOT interchangeable unless the Drive Line Control Module (DLCM) is also replaced. · 68550586A$ service RDMs have a 20 clutch plate design · Not all 20-plate RDMs have the new pump design. The new pump requires a new DLCM. · All new service RDMs are shipped with the new pump design. · If a new 68550586AA service RDMs is installed, then replace the DLCM with new DLCM 68540647AA - 1-spd designed for the 20-plate RDM. 1.2) If replacing the DLCM but not the RDM or pump assembly, then · If the RDM is the original 24 plate design then use 68540645AA - 1-spd, 24 plate DLCM AND replace the pump with 68551790AA · If the RDM is the new 20 plate design then use 68540647AA - 1-spd, 20 plate DLCM AND also replace the pump with 68551790AA new pump unless the RDM previously had a 68551790AA installed. 1.3) If replacing the pump assembly, then use 68551790AA (new pump) AND also replace the DLCM with the version that matches the correct version of the RDM (24 or 20 plate). · Use 68540645AA for the 24 plate RDM with a new pump. · Use 68540647AA for the 20 plate RDM with a new pump. 2) For 2016 and later VINs with DK2 = 1-spd RDM Early 2016 were built with 68090612AG 24 plate RDMs. Use Section 1 ?For 2014/5 VINs with DK2 = 1-spd RDM? to resolve. The balance of M |
| 9004402 | 2022-08-22. Service bulletin. SERVICE BRAKES, HYDRAULIC; ELECTRONIC STABILITY CONTROL:AUTOMATIC (ASC); ELECTRICAL SYSTEM; FUEL SYSTEM, GASOLINE; BACK OVER PREVENTION. DIFFERENTIAL, Rear Axle (KL 4WD w/DK4 = 2-SPEED RDM) The Differential, Rear Axle (aka RDM) design, pump design, Driveline Control Module (aka DLCM) hardware & software and pressure sensor have all changed in the past few years. The chages are not interchangeable and each had a separate implementation date. Please comprehend it to avoid repeat repairs. There are 2 sections each with 3 sub-sections: 1) For 2014/5 VINs with DK2 = 1-spd RDM 2) For 2016 and later VINs with DK2 = 1-spd RDM 1) For 2014/5 VINs with DK4 = 2-spd RDM 2014 - 2015 VINs built with a 2-speed RDM used a 24 plate clutch design. Service RDMs (DK4: 68545100AA and DK4 + AWL: 68545101AA) have a 20-plate design. 1.1) If replacing the RDM · 24-plate and 20-plate design RDMs are NOT interchangeable unless the Drive Line Control Module (DLCM) is also replaced. · Both 68545100A$ and 68545101A$ service RDMs have a 20 clutch plate design · Not all 20 plate RDMs have the new pump design. The new pump requires a new DLCM. · All new service RDMs are shipped with the new pump design. · If a new 20 plate service RDM is installed, then replace the DLCM with new DLCM 68383660AE - 2-spd designed for the 20 plate RDM. 1.2) If replacing the DLCM but not the RDM or pump assembly, then · If the RDM is the original 24 plate design then use 68540646AA - 2-spd, 24 plate DLCM AND also replace the pump with 68551790AA new pump. · If the RDM is the new 20 plate design then use 68383660AE - 2-spd, 20 plate DLCM AND also replace the pump with 68551790AA new pump unless the RDM previously had a 68551790AA installed. 1.3) If replacing the pump assembly, then use 68551790AA (new pump) AND also replace the DLCM with the version that matches the correct version of the RDM (24 or 20 plate). · Use 68540646AA for the 24-plate RDM with a new pump. · Use 68383660AE for the 20-plate RDM with a new pump. 2) Early 2016 were built with 24 plate RDMs. These include p/n?s 68090615AJ (2spd std), and 52123642AJ (2spd locker). Use Secti |
| Z5091195A | 2022-08-22. Service bulletin. EQUIPMENT; ELECTRICAL SYSTEM; EQUIPMENT:ELECTRICAL. RES / RHA / REB radio that supports Bluetooth and Hands-Free For issues with Bluetooth, Hands-Free Calling, and/or Voice Commands, DO NOT replace the radio. Diagnose the Hands-Free Module system (also called the Telematics Module). The Telematics Module (and associated components) is the system responsible for these features. A power cycle may be required for the hands-free module for proper diagnosis.~ Please reference; 8T - Navigation/Telecommunication Diagnosis and Testing (DIAGNOSIS AND TESTING - HANDS FREE PHONE) |
| 03-003-16 | 2022-08-22. Service bulletin. ELECTRICAL SYSTEM. Drivetrain Control Module (DTCM) This bulletin involves replacing and reconfiguring the Drivetrain Control Module (DTCM) with the latest available software. Some vehicles may experience a constant high pitched whine coming from rear axle area. |
| 08-064-16 | 2022-08-22. Service bulletin. ELECTRICAL SYSTEM. Headlamp Leveling Switch Position Not Correct This bulletin involves running the wiTECH function: Configure BUX Headlamp Parameters. Customers may describe that the headlamp leveling switch positions are opposite of the actual headlamp positions (Fig. 1). For example, switch down position is headlamps up and vice versa. |
The summaries are NHTSA's. Each bulletin's page links NHTSA's copy of the manufacturer's document.