WenmarOpen by Wenmar Pro

Service bulletins for the 2017 Infiniti QX60

A bulletin is a manufacturer's communication to its dealers, as NHTSA indexes it. The summary is NHTSA's. The document is the manufacturer's: read it at NHTSA. A bulletin is not a recall, and listing a model year does not mean every vehicle of it is concerned.

214 on file from NHTSA, as of 2026-10-19.

By type

By component

By trouble code

Bulletins, newest first
ITB13-026k2020-02-07. Service bulletin. EQUIPMENT. 2014-2017 INFINITI; DISPLAY CONTROL UNIT REPLACEMENT This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
ITB13-008a2020-02-07. Service bulletin. SUSPENSION. CLICKING NOISE FROM FRONT OR REAR AXLE DURING TAKE-OFF/ACCELERATION This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
P9329_P9344_P9342020-01-09. Service bulletin. ENGINE AND ENGINE COOLING. Engine Control Module (ECM) Reprogram California Voluntary Emission Service Campaign ***** Campaign Summary ***** INFINITI is conducting a Voluntary Emissions Service Campaign on approximately 49,497 specific INFINITI vehicles identified in Service Comm and currently registered to owners in the state of California to reprogram the Engine Control Module (ECM) in the event that a permanent diagnostic trouble code (P-DTC) for P0448, P0101, P2008, or P0087 is recorded in the ECM. Due to calibration errors on the affected vehicles, the ECM may improperly store a permanent diagnostic trouble code (P-DTC) even though the emissions on-board diagnostic system is functioning properly. As of July 1, 2019 the State of California has implemented a revised Inspection Maintenance (I/M) or “Smog Check” test program. Without the software update, the subject vehicles may not pass this Smog Check test in those areas of California where such testing is required under state law. This incident has no effect on the safety, performance, drivability, or fuel consumption of the applicable vehicles. ***** What Retailers Should Do ***** 1. Verify if vehicles are affected by this Voluntary Emissions Service Campaign using Service Comm or DBS National Service History – Open Campaign I.D. • P9329 – Affected Model Year 2015 • P9344 – Affected Model Year 2016 • P9346 – Affected Model Year 2017 • P9348 – Affected Model Year 2018 • P9350 – Affected Model Year 2019 2. Retailers are requested to repair any affected vehicles in retailer new or pre-owned inventory to ensure client satisfaction. • - New vehicles in retailer inventory can also be identified DBS (Sales-> Vehicle Inventory, and filter by Open Campaign). • - Refer to IPSB 15-286 for additional information 3. Retailers should use ITB19-043 to correct any vehicles subject to this campaign.
ITB19-0432020-01-09. Service bulletin. ENGINE AND ENGINE COOLING. VOLUNTARY EMISSIONS SERVICE CAMPAIGN VEHICLES REGISTERED IN CALIFORNIA; ENGINE CONTROL MODULE INTRODUCTION Infiniti is conducting this voluntary emissions service campaign on certain specific model year Infiniti vehicles (see APPLIED VEHICLES) registered in the state of California. The engine control module (ECM) will be inspected, and reprogrammed if it applies. This service will be performed at no charge to the customer for parts or labor. IDENTIFICATION NUMBER Infiniti has assigned identification numbers P9329, P9344, P9346, P9348, and P9350 to this campaign. The correct number must appear on all communication and documentation of any nature dealing with this campaign. RETAILER RESPONSIBILITY Retailers are to repair vehicles falling within range of this campaign that enter the service department. This includes vehicles purchased from private parties, vehicles presented by transient (tourists) owners, and vehicles in a retailer’s inventory.
ITB16-035b2019-11-07. Service bulletin. POWER TRAIN. 2015-2017 QX60; ENHANCED DIAGNOSTIC LOGIC FOR CVT This bulletin has been superseded by ITB15-012. Please discard previous versions of this bulletin.
ITB15-012h2019-11-07. Service bulletin. POWER TRAIN. 2013 JX35 AND 2014 – 2018 QX60; CVT JUDDER AND DTC P17F0 OR P17F1 STORED This bulletin has been amended. See AMENDMENT HISTORY on the last page. Discard all previous versions of this bulletin.
ITB15-010d2019-11-07. Service bulletin. POWER TRAIN. INFINITI; PROCEDURE TO CLEAN CVT TRANSMISSION FLUID COOLERS This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
ITB12-011o2019-11-07. Service bulletin. EQUIPMENT. TELEMATICS SERVICE INFORMATION This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
ITB14-011d2019-10-09. Service bulletin. ENGINE AND ENGINE COOLING. REMOTE ENGINE START NOT WORKING This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
ITB19-0272019-10-08. Service bulletin. ELECTRICAL SYSTEM; ENGINE AND ENGINE COOLING. MIL ON WITH DTC P0087, P0101, P0448, OR P2008 IF YOU CONFIRM An applied vehicle has one or more DTCs stored, shown in Table A on page 2, AND The ECM part number is shown in Table B, starting on page 3. ACTION 1. First perform the appropriate diagnostic procedure for the stored DTC to repair the vehicle according to the Electronic Service Manual (ESM). 2. Reprogram the ECM after performing the diagnosis and repair. • -The ECM reprogram in this Service Procedure is not a repair for the DTC, but instead updates the way the permanent DTC is stored and allowed to be erased. The DTC must be properly diagnosed and repaired before the reprogram is applied.
ITB19-0242019-10-08. Service bulletin. SEATS; ELECTRICAL SYSTEM; AIR BAGS. DTC B00A0-00 STORED IF YOU CONFIRM DTC B00A0-00 (OCCUPANT DETECTION SENSOR UNIT) is stored And OCS zero point reset cannot be performed And The following screen will display: ACTION 1. Check the Occupant Classification System (OCS) control unit using the ODS Analysis tool software. • Refer to SERVICE PROCEDURE on the next page. HINT: “OCS” may also be referred to as “ODS”. 2. Perform “75-zero RESET”.
ITB18-040c2019-10-08. Service bulletin. EQUIPMENT; ELECTRICAL SYSTEM:SOFTWARE; ELECTRICAL SYSTEM. SOFTWARE UPDATES FOR INFOTAINMENT ISSUES This bulletin has been amended. See AMENDMENT HISTORY on the last page. Discard all previous versions of this bulletin.
ITB19-0252019-10-08. Service bulletin. POWER TRAIN. QX60; TRANSMISSION RANGE SWITCH SERVICE INFORMATION SERVICE INFORMATION The transmission range switch is now available as a separate service part. If the transmission range switch is being replaced for any reason, it must be adjusted after its replacement. • - Refer to SERVICE PROCEDURE on page 3 for transmission range switch removal, installation, and adjustment.
ITB19-0222019-09-10. Service bulletin. ELECTRICAL SYSTEM. 2017-2019 QX60; MIL ON WITH DTC P0087 STORED IF YOU CONFIRM The Malfunction Indicator Light (MIL) is ON with Diagnostic Trouble Code (DTC) P0087 (FRP CONTROL SYSTEM) stored in the Engine Control Module (ECM), AND The fuel level indicates ¼ or less. ACTION Reprogram the ECM, if applicable.
ITB13-026J2019-08-19. Service bulletin. ELECTRICAL SYSTEM. 2014-2017 INFINITI; DISPLAY CONTROL UNIT REPLACEMENT This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
ITB19-0142019-07-22. Service bulletin. EXTERIOR LIGHTING:HEADLIGHTS. 2013 JX35 AND 2014-2020 QX60; REMOVAL OF HEADLIGHT ASSEMBLY LOCATING BRACKET SERVICE INFORMATION If replacement of a Front Combination Headlamp assembly (headlight assembly) is necessary, for the applied vehicles, the locating bracket (if present) on the new replacement headlight assembly must first be removed before installation. Inspect the new replacement headlight assembly and confirm if a locating bracket is attached, with a Torx screw, on top in the center (see Figure 1). Is a locating bracket present? - NO: This bulletin does not apply. Continue with the installation of the new replacement headlight assembly. - YES 1. Using a T10 Torx screwdriver, remove the locating bracket attached to the topcenter of the replacement headlight assembly (see Figure 1). 2. Discard the locating bracket and Torx screw. 3. Continue the installation of the replacement headlight assembly. NOTE: Refer to the Electronic Service Manual (ESM) for the procedure to remove or install a headlight assembly. CAUTION: Take care when installing the headlight assembly so that the painted surface of the fender is not damaged. - Black electrical tape can be used to protect the edge of the fender while installing the headlight assembly.
ITB14-053b2019-07-22. Service bulletin. EQUIPMENT. ABNORMAL NOISE FROM FRONT ENGINE MOUNT This bulletin has been amended. See AMENDMENT HISTORY on the last page. Discard all previous versions of this bulletin.
ITB12-011n2019-07-22. Service bulletin. EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL. TELEMATICS SERVICE INFORMATION This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
ITB19-0132019-06-24. Service bulletin. LANE DEPARTURE: SENSING SYSTEM: CAMERA; EQUIPMENT:ELECTRICAL. AEB WARNING LIGHT BLINKING This bulletin applies only to vehicles equipped with a lane camera. SERVICE INFORMATION If the AEB warning light is blinking (but not illuminated steadily) or the customer states it is blinking, and there are no related DTCs, inspect the windshield. A blinking AEB warning light may occur under the following conditions: - When contamination or foreign material adhere to the lane camera viewing window on the windshield - When driving while it is snowing or when frost forms on the lane camera viewing window on the windshield - When the lane camera viewing window on the windshield is temporarily fogged up NOTE: - If DTCs are present in any of the following related systems: - Laser/Radar, - ICC/ADAS, or - Lane Camera, Refer to the related Electronic Service Manual (ESM) for diagnosis. - Refer to the following pages for further information.
ITB19-0112019-06-24. Service bulletin. EQUIPMENT. DEAD PEDAL REPLACEMENT SERVICE INFORMATION If the dead pedal needs to be replaced for anyreason, it is no longer necessary to replace the front floor trim (carpet). The dead pedal is now available as a service part. NOTE: Do not replace the carpet if only the dead pedal is needed. ACTION Follow the SERVICE PROCEDURE on the next page to replace ONLY the dead pedal. NOTE: Dead pedal is listed in PARTS INFORMATION on the last page.
ITB19-0102019-05-20. Service bulletin. FUEL SYSTEM, GASOLINE; FUEL SYSTEM, GASOLINE:FUEL INJECTION SYSTEM. 2016-2018 QX60; MIL ON WITH DTC P2097, P2099, P0171 AND/OR P0174 This bulletin applies only to vehicles equipped with the VQ35DE engine only. IF YOU CONFIRM The MIL is ON with one or more of the following Air/Fuel (A/F) Sensor DTCs stored: - P0171 (Fuel Injection System Function) - P0174 (Fuel Injection System Function) - P2097 (A/F SENSOR 1) - P2099 (A/F SENSOR 1) ACTION 1. Perform the appropriate diagnostic procedure outlined in the Electronic Service Manual (ESM). 2. Refer to Table A on the next page to confirm if Electronic Control Module (ECM) reprogramming is needed.
ITB19-0082019-05-20. Service bulletin. EQUIPMENT. EXTERIOR CLEANING INFORMATION SERVICE INFORMATION When cleaning the exterior of an Infiniti vehicle, damage may occur when using a cleaner with too high of an alkaline concentration. - Always refer to the Appearance and care section of the related owner?s manual. - Not all cleaners are created equal. - Many cleaners come in concentrated form. - Alkaline cleaners (cleaners with a high pH value) can cause spots on paint and trim when not used as directed. - Some commercial car washes use cleaners with a high pH value. - When using cleaners that meet the conditions defined in the Appearance and care section, be sure to carefully follow the cleaner?s directions. - When finished cleaning/washing, rinse thoroughly with clean water. IMPORTANT: Damage to paint, glass, bright metal, or any other exterior surface caused by using improper cleaning products is not covered under warranty. Always refer to the Paint Incident Identification Manual (PIIM) and Assurance Products Reference Manual (APRM). Follow the guidelines in the PIIM and APRM for non-warrantable exterior body, glass, or painted surface quality issues. To access the PIIM and APRM, login to nnanet.com: - For the PIIM, select: MY LINKS > Warranty > Paint Incident Identification Manual - For the APRM, select: MY DOCUMENTS > Warranty > APRM See further information in this bulletin.
ITB19-0072019-04-15. Service bulletin. EQUIPMENT; FUEL SYSTEM, OTHER. INFINITI; P0171 AND P0174 SERVICE INFORMATION SERVICE INFORMATION Diagnosis for DTCs P0171 (FUEL SYS LEAN B1) and P0174 (FUEL SYS LEAN B2) have been revised for the APPLIED VEHICLES listed above. When performing diagnosis for either of these DTCs, start by using the SERVICE PROCEDURE section of this bulletin. NOTE: The related Electronic Service Manuals (ESM) will be revised in the future to include these diagnostic steps.
ITB19-0062019-04-15. Service bulletin. ELECTRICAL SYSTEM; EQUIPMENT. INFINITI; MIL ON WITH DTC P219A AND/OR P219B STORED SERVICE INFORMATION If the MIL is ON and DTC P219A (AIR FUEL RATIO IMBALANCE B1) and/or P219B (AIR FUEL RATIO IMBALANCE B2) is stored: - DO NOT replace the Air Fuel Ratio (A/F) sensor. - Refer to the applicable Electronic Service Manual (ESM) and follow the diagnostic procedure for DTC P219A and/or P219B.
ITB18-040b2019-04-15. Service bulletin. ELECTRICAL SYSTEM; EQUIPMENT. SOFTWARE UPDATES FOR INFOTAINMENT ISSUES This bulletin has been amended. Please see Amendment History on the last page. Please discard previous versions of this bulletin.

The summaries are NHTSA's. Each bulletin's page links NHTSA's copy of the manufacturer's document.