Recalls that may apply to the 2008 Infiniti QX56
A recall listed here may apply to a vehicle of this year, make and model. Only the manufacturer can say whether it applies to one vehicle: check the VIN with the official lookups.
By component
| 10V349000 | 2010-07-22. AIR BAGS:SIDE/WINDOW. NISSAN IS RECALLING MODEL YEAR 2008 NISSAN ARMADA AND INFINITI QX56 VEHICLES MANUFACTURED FROM FEBRUARY 7, 2007 THROUGH FEBRUARY 14, 2007. THESE VEHICLES FAIL TO COMPLY WITH THE REQUIREMENTS OF FEDERAL MOTOR VEHICLE SAFETY STANDARD NO. 201, "PROTECTION IN INTERIOR IMPACT." AN OUT-OF-SPECIFICATION A-PILLAR FINISHER MIGHT IMPEDE THE CORRECT INFLATION OF THE SIDE CURTAIN AIR BAG NEAR THE UPPER PORTION OF THE B-PILLAR. Built 2007-02-07 to 2007-02-14. |
|---|---|
| 10V074000 | 2010-03-03. FUEL SYSTEM, OTHER:STORAGE:FUEL GAUGE SYSTEM. NISSAN IS RECALLING CERTAIN MODEL YEAR 2005-2009 TITAN, ARMADA, AND INFINITI QX56 VEHICLES. THE INSTRUMENT PANEL FUEL GAUGE MAY INACCURATELY DISPLAY THAT THE VEHICLE STILL HAS SOME FUEL, TYPICALLY ABOUT ONE QUARTER TANK, WHEN THE FUEL TANK IS EMPTY. |
| 10V072000 | 2010-03-02. SERVICE BRAKES, HYDRAULIC:PEDALS AND LINKAGES. NISSAN IS RECALLING CERTAIN MODEL YEAR 2008-2010 TITAN, ARMADA, AND INFINITI QX56, AND MODEL YEAR 2008-2009 NISSAN QUEST VEHICLES. THE BRAKE PEDAL PIVOT PIN END WAS NOT SPIN-FORMED TO SPECIFICATION DURING THE MANUFACTURING PROCESS OF THE BRAKE PEDAL ASSEMBLY. THE PIVOT PIN COULD SLIDE AND CAUSE THE BRAKE PEDAL TO PARTIALLY DISENGAGE FROM THE BRAKE PEDAL BRACKET. Built 2007-02-09 to 2009-12-14. |
| 2012156 | 2012-04-11. Label. Certain vehicles fail to comply with the requirements of Canada Motor Vehicle Safety Standard 210.1 - User-ready Tether Anchorages for Restraint Systems. Specifically, the pictograms identifying the location of the tether anchors measure 15 mm in height instead of 20 mm as required by the Standard. Correction: Since this non-compliance condition does not pose any safety risk, no corrective action is required. |
|---|---|
| 2010062 | 2010-03-03. Brakes. On certain vehicles, the brake pedal pivot pin end was not properly manufactured. As a result, the pin may not remain in place, causing the brake pedal to partially disengage from the brake pedal bracket. If this occurs, the driver will experience unusual and noticeable looseness in the pedal and a reduction in braking force. A reduction in braking force may lead to increased stopping distances and the risk of a crash causing property damage, personal injury or death. Correction: Owners of all potentially affected vehicles will be contacted and their brake pedal assembly will be inspected and replaced if necessary. |
| 2010060 | 2010-03-02. Fuel System. On certain vehicles, the material used on fuel level sending unit contacts can wear and contaminate the sender. This causes the instrument panel fuel gauge to display that the vehicle still has some fuel left in the tank when the fuel tank is empty. An inaccurate fuel gauge can lead to engine stalling while driving, which may increase the risk of a crash causing property damage, personal injury or death. Correction: Letters will be sent to owners in two stages. The first letter will advise owners of fuel gauge inaccuracy and recommend maintaining a fuel level above the one half position. The second letter will follow, requesting owners bring their vehicles to a dealer for replacement of the fuel sender unit. |
A campaign lists a year, a make and a model, and often only some of the vehicles built. A list with nothing on it is not a clearance either. The lookups below check one VIN.
Check one vehicle officially
Contains information licensed under the Open Government Licence – Canada.