WenmarOpen by Wenmar Pro

Service bulletins for the 2017 Infiniti Q60

A bulletin is a manufacturer's communication to its dealers, as NHTSA indexes it. The summary is NHTSA's. The document is the manufacturer's: read it at NHTSA. A bulletin is not a recall, and listing a model year does not mean every vehicle of it is concerned.

188 on file from NHTSA, as of 2026-10-19.

By type

By component

By trouble code

Bulletins, newest first
ITB19-0432020-01-09. Service bulletin. ENGINE AND ENGINE COOLING. VOLUNTARY EMISSIONS SERVICE CAMPAIGN VEHICLES REGISTERED IN CALIFORNIA; ENGINE CONTROL MODULE INTRODUCTION Infiniti is conducting this voluntary emissions service campaign on certain specific model year Infiniti vehicles (see APPLIED VEHICLES) registered in the state of California. The engine control module (ECM) will be inspected, and reprogrammed if it applies. This service will be performed at no charge to the customer for parts or labor. IDENTIFICATION NUMBER Infiniti has assigned identification numbers P9329, P9344, P9346, P9348, and P9350 to this campaign. The correct number must appear on all communication and documentation of any nature dealing with this campaign. RETAILER RESPONSIBILITY Retailers are to repair vehicles falling within range of this campaign that enter the service department. This includes vehicles purchased from private parties, vehicles presented by transient (tourists) owners, and vehicles in a retailer’s inventory.
ITB12-011o2019-11-07. Service bulletin. EQUIPMENT. TELEMATICS SERVICE INFORMATION This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
ITB14-011d2019-10-09. Service bulletin. ENGINE AND ENGINE COOLING. REMOTE ENGINE START NOT WORKING This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
ITB19-0282019-10-08. Service bulletin. ENGINE AND ENGINE COOLING. Q50 AND Q60 WITH VR30DDTT (V6) ENGINE; ENGINE OIL DRAIN PLUG SERVICE INFORMATION SERVICE INFORMATION Whenever installing an engine oil drain plug on an APPLIED VEHICLE with a VR30DDTT (V6) engine, NEVER tighten the drain plug greater than its specified torque. Over-tightening may loosen the threaded insert in the oil pan (lower), causing an oil leak. ALWAYS replace the drain plug gasket after removing the drain plug, and then tighten the drain plug to the specified torque. • VR30DDTT (V6) engine oil drain plug torque (with new gasket): • 2WD and AWD: 33.5 N•m (3.4 kg-m, 25 ft-lbs) • Avoid contact with the engine oil as it may be hot and cause burns. • Avoid prolonged or repeated contact with used engine oil as it may cause skin cancer. Try to avoid direct skin contact with used engine oil. If skin contact is made, wash with a suitable hand cleaner or soap as soon as possible.
ITB19-0272019-10-08. Service bulletin. ELECTRICAL SYSTEM; ENGINE AND ENGINE COOLING. MIL ON WITH DTC P0087, P0101, P0448, OR P2008 IF YOU CONFIRM An applied vehicle has one or more DTCs stored, shown in Table A on page 2, AND The ECM part number is shown in Table B, starting on page 3. ACTION 1. First perform the appropriate diagnostic procedure for the stored DTC to repair the vehicle according to the Electronic Service Manual (ESM). 2. Reprogram the ECM after performing the diagnosis and repair. • -The ECM reprogram in this Service Procedure is not a repair for the DTC, but instead updates the way the permanent DTC is stored and allowed to be erased. The DTC must be properly diagnosed and repaired before the reprogram is applied.
ITB19-0242019-10-08. Service bulletin. SEATS; ELECTRICAL SYSTEM; AIR BAGS. DTC B00A0-00 STORED IF YOU CONFIRM DTC B00A0-00 (OCCUPANT DETECTION SENSOR UNIT) is stored And OCS zero point reset cannot be performed And The following screen will display: ACTION 1. Check the Occupant Classification System (OCS) control unit using the ODS Analysis tool software. • Refer to SERVICE PROCEDURE on the next page. HINT: “OCS” may also be referred to as “ODS”. 2. Perform “75-zero RESET”.
ITB18-040c2019-10-08. Service bulletin. EQUIPMENT; ELECTRICAL SYSTEM:SOFTWARE; ELECTRICAL SYSTEM. SOFTWARE UPDATES FOR INFOTAINMENT ISSUES This bulletin has been amended. See AMENDMENT HISTORY on the last page. Discard all previous versions of this bulletin.
ITB17-004b2019-09-10. Service bulletin. ENGINE AND ENGINE COOLING. ACCESSORY DRIVE BELT NOISY OR HAS COME OFF This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
ITB13-026J2019-08-19. Service bulletin. ELECTRICAL SYSTEM. 2014-2017 INFINITI; DISPLAY CONTROL UNIT REPLACEMENT This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
ITB12-011n2019-07-22. Service bulletin. EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL. TELEMATICS SERVICE INFORMATION This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
ITB19-0082019-05-20. Service bulletin. EQUIPMENT. EXTERIOR CLEANING INFORMATION SERVICE INFORMATION When cleaning the exterior of an Infiniti vehicle, damage may occur when using a cleaner with too high of an alkaline concentration. - Always refer to the Appearance and care section of the related owner?s manual. - Not all cleaners are created equal. - Many cleaners come in concentrated form. - Alkaline cleaners (cleaners with a high pH value) can cause spots on paint and trim when not used as directed. - Some commercial car washes use cleaners with a high pH value. - When using cleaners that meet the conditions defined in the Appearance and care section, be sure to carefully follow the cleaner?s directions. - When finished cleaning/washing, rinse thoroughly with clean water. IMPORTANT: Damage to paint, glass, bright metal, or any other exterior surface caused by using improper cleaning products is not covered under warranty. Always refer to the Paint Incident Identification Manual (PIIM) and Assurance Products Reference Manual (APRM). Follow the guidelines in the PIIM and APRM for non-warrantable exterior body, glass, or painted surface quality issues. To access the PIIM and APRM, login to nnanet.com: - For the PIIM, select: MY LINKS > Warranty > Paint Incident Identification Manual - For the APRM, select: MY DOCUMENTS > Warranty > APRM See further information in this bulletin.
ITB19-0072019-04-15. Service bulletin. EQUIPMENT; FUEL SYSTEM, OTHER. INFINITI; P0171 AND P0174 SERVICE INFORMATION SERVICE INFORMATION Diagnosis for DTCs P0171 (FUEL SYS LEAN B1) and P0174 (FUEL SYS LEAN B2) have been revised for the APPLIED VEHICLES listed above. When performing diagnosis for either of these DTCs, start by using the SERVICE PROCEDURE section of this bulletin. NOTE: The related Electronic Service Manuals (ESM) will be revised in the future to include these diagnostic steps.
ITB18-040b2019-04-15. Service bulletin. ELECTRICAL SYSTEM; EQUIPMENT. SOFTWARE UPDATES FOR INFOTAINMENT ISSUES This bulletin has been amended. Please see Amendment History on the last page. Please discard previous versions of this bulletin.
ITB19-0052019-03-25. Service bulletin. EQUIPMENT:ELECTRICAL; EQUIPMENT:ELECTRICAL:NAVIGATIONAL SYSTEM(GLOBAL POSITIONING SYSTEM); EQUIPMENT:ELECTRICAL:RADIO/TAPE DECK/CD ETC.; EQUIPMENT. CLOCK, AUDIO, HVAC OR NAVIGATION SETTINGS INTERMITTENTLY CHANGE ON THEIR OWN This bulletin applies only to vehicles equipped with INFINITI InTouch (Intelligent Key). SERVICE INFORMATION An Intelligent Key, for the applied vehicles with INFINITI InTouch?, has the abillity to trigger specific customized settings for the radio, clock, heating and air conditioning (HVAC) and navigation that are unique to that key, and each Intelligent Key for a specific vehicle may have different settings stored. EXAMPLE: The vehicle may be driven by more than one person, and each driver has a personal Intelligent Key. Each driver may adjust their preferred vehicle settings differently. If two or more Intelligent Keys with different stored settings are unintentionally interchanged, one or more of the following perceived issues might be reported by the customer(s). - Radio ? Presets are lost or change - Clock ? Settings are not showing the correct time due to day-light savings or the selected region (time zone) - HVAC ? Controls are set differently - Navigation ? Settings suddenly altered If any of these perceived issues are present: - Confirm if there are multiple Intelligent Keys being used by the customer(s) interchangeably, and if so, verify that each key?s settings are different. NOTE: Customer may not recognize that different Intelligent Keys are linked differently.
ITB17-017a2019-03-25. Service bulletin. ELECTRICAL SYSTEM. MIL ON WITH DTC P0101, P010B, AND/OR P0106 This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
ITB16-012b2019-03-25. Service bulletin. EQUIPMENT; EQUIPMENT:ELECTRICAL. INTELLIGENT KEY BUTTONS INOPERATIVE BUT REQUEST SWITCHES WORK This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
ITB18-040a2019-02-25. Service bulletin. ELECTRICAL SYSTEM:SOFTWARE; EQUIPMENT. INFINITI; SOFTWARE UPDATES FOR INFOTAINMENT ISSUES This bulletin has been amended. Please see Amendment History on the last page. Please discard previous versions of this bulletin.
ITB18-0402019-02-25. Service bulletin. ELECTRICAL SYSTEM:SOFTWARE; EQUIPMENT. INFINITI; SOFTWARE UPDATES FOR INFOTAINMENT ISSUES IF YOU CONFIRM Any one or a combination of the following on an applied vehicle: - Reverse camera is blank (vehicles manufactured before May 1, 2018) - Reverse camera remains ON when in Drive (vehicles manufactured before May 1, 2018) - Average fuel economy displays 99.9 MPG - Display screen flickers at higher ambient interior temperatures - SXM Info Apps (Weather, Stocks, Fuel Prices) inoperative ACTION 1. Refer to page 4, step 8 in the SERVICE PROCEDURE to confirm an update applies to the Display Control Unit (DCU) of the vehicle being worked on. - Confirmation is determined by comparing the DCU part number with those listed in Table on page 5. 2. If this bulletin applies, update the DCU software. - See REQUIRED SPECIAL TOOL on page 2. NOTE: The updated software resolves the items above along with improving software stability.
ITB19-0012019-02-19. Service bulletin. ELECTRICAL SYSTEM; EQUIPMENT. CHASSIS CONTROL MODULE DTC INFORMATION SERVICE INFORMATION If one or more of the following Chassis Control DTCs are stored: - C1BA0-00 - (CHASSIS CONTROL BRAKE SYSTEM) - C1B90-00 - (DIRECT ADAPTIVE STEERING SYSTEM) - C1B92-00 - (BRAKE CONTROL SYSTEM) - C1B93-00 - (ENGINE/HEV SYSTEM) - C1B94-00 - (TRANSMISSION SYSTEM) And One or more additional DTCs, other than those above, are also stored in a control unit other than the Chassis Control Module. - Perform the diagnostic/repair procedures for the additional DTCs of the other control unit FIRST. - Refer to the Electronic Service Manual (ESM) for DTC specific diagnostic information. Do not replace the CHASSIS CONTROL MODULE (CONTROLLER ASSY-IDM) if additional DTCs are present.
ITB17-042b2019-02-19. Service bulletin. ENGINE AND ENGINE COOLING. INFINITI; DTC P0456 CAUSED BY EVAP LEAK AT VENT CONTROL VALVE O-RING This bulletin has been amended. See Amendment History on the last page. Please discard previous versions of this bulletin.
ITB13-044g2019-02-19. Service bulletin. ENGINE AND ENGINE COOLING. ALL MODEL YEAR 2012 AND NEWER INFINITI VEHICLES; EVAP LEAK DTC P0442, P0455, P0456 INFORMATION This bulletin has been amended. See Amendment History on the last page. Please discard previous versions of this bulletin.
ITB13-026i2019-02-19. Service bulletin. EQUIPMENT:ELECTRICAL. 2014-2017 INFINITI VEHICLES; DISPLAY CONTROL UNIT REPLACEMENT This bulletin has been amended. See AMENDMENT HISTORY on the last page. Discard all previous versions of this bulletin.
ITB12-011m2019-02-19. Service bulletin. EQUIPMENT:ELECTRICAL:NAVIGATIONAL SYSTEM(GLOBAL POSITIONING SYSTEM). TELEMATICS SERVICE INFORMATION This bulletin applies only to vehicles equipped with factory Navigation system. This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
ITB18-0392019-01-07. Service bulletin. AIR BAGS. AIR BAG WARNING LIGHT FLASHING INDICATING SYSTEM DIAGNOSTIC MODE IF YOU CONFIRM The air bag warning light is flashing slowly (repeating 2 seconds ON, 2 seconds OFF). NOTE: If this should occur, the Air Bag Diagnosis Sensor Unit is in Diagnostic Mode and needs to be returned to User Mode. ACTION 1. Use CONSULT-III plus to check for Air Bag DTCs and perform repairs as needed. 2. Return the Air Bag Diagnosis Sensor Unit to User Mode.
Revision 1-IEVAP2019-01-07. Service bulletin. ENGINE; EQUIPMENT. OBD II EVAP Tube Warranty Enhancement The update below was sent out to Regions and Retailers in August of this year. We are re-circulating this update to make regional and retailer personnel aware that we are re-notifying clients at this time.

The summaries are NHTSA's. Each bulletin's page links NHTSA's copy of the manufacturer's document.