WenmarOpen by Wenmar Pro

Service bulletins for the 2015 Infiniti Q50

A bulletin is a manufacturer's communication to its dealers, as NHTSA indexes it. The summary is NHTSA's. The document is the manufacturer's: read it at NHTSA. A bulletin is not a recall, and listing a model year does not mean every vehicle of it is concerned.

207 on file from NHTSA, as of 2026-10-19.

By type

By component

By trouble code

Only bulletins with component: Steering are shown. Show all

Bulletins, newest first
P5326OL2021-05-10. Service bulletin. ELECTRICAL SYSTEM; STEERING. Infiniti is conducting a Voluntary Service Campaign on certain specific Model Year 2014 - 2015 Q50 Hybrid cold state vehicles (listed below) to reprogram the Direct Adaptive Steering (DAST) and replace the 12 volt battery.
P5323OL2021-05-10. Service bulletin. STEERING. Infiniti is conducting a Voluntary Service Campaign on certain specific Model Year 2014 - 2015 Q50 Hybrid cold state vehicles (listed below) to reprogram the Direct Adaptive Steering (DAST) and replace the 12 volt battery.
P53232021-05-10. Service bulletin. ELECTRICAL SYSTEM; STEERING. Infiniti is conducting a Voluntary Service Campaign on certain specific Model Year 2014 - 2015 Q50 Hybrid cold state vehicles (listed below) to reprogram the Direct Adaptive Steering (DAST) and replace the 12 volt battery.
P53262021-05-10. Service bulletin. STEERING. Infiniti is conducting a Voluntary Service Campaign on certain specific Model Year 2014 - 2015 Q50 Hybrid cold state vehicles (listed below) to reprogram the Direct Adaptive Steering (DAST) and replace the 12 volt battery.
ITB15001A2021-05-10. Service bulletin. STEERING; AIR BAGS; BACK OVER PREVENTION; WHEELS. IF YOU CONFIRM The steering wheel makes a faint squeaking/ticking noise when turned left or right. NOTE: Due to the faint nature of this noise it may be necessary to lift front wheels off of the ground so that it can be isolated. ACTION Remove driver?s side airbag and apply felt tape with the SERVICE PROCEDURE starting on page 2. See this bulletin for further detail.
ITB10037D2021-05-10. Service bulletin. VISIBILITY; AIR BAGS; STEERING. SERVICE INFORMATION The Applied Vehicles are equipped with a new version of Intelligent Key presets memory. Each Intelligent Key can be programmed to have its own unique set of presets for certain vehicle systems. Vehicle systems that are linked with Intelligent Key include: - Automatic Drive Positioner (includes driver seat, steering column, and mirror position memory) - Audio (station presets, etc.) - Auto air conditioning and heating (retains the last temperature and mode setting for each Intelligent Key user) - Navigation system (retains the last settings [e.g., Birdview] and clock display preference for each Intelligent Key user) See this bulletin for further detail.
ITB150252021-05-10. Service bulletin. BACK OVER PREVENTION; EQUIPMENT; WHEELS; SERVICE BRAKES; STEERING. SERVICE INFORMATION When servicing run flat tires or low profile tires: - Special equipment and procedures are required to avoid damage. - Specifically, Tire Pressure Monitor transmitters (TPMS sensors) can be damaged when improperly dismounting and mounting tires. - TPMS sensors becoming damaged during mounting or dismounting tires are not covered under warranty. - To avoid such damage, ensure that the tire changer being used and the operator of the tire changer are capable of servicing run flat and low profile tires. - Operator?s manuals for such tire changers must be followed. See this bulletin for further detail.
ITB18-0212018-06-18. Service bulletin. STEERING; ELECTRICAL SYSTEM. DAST CALIBRATION (MODE1) INCOMPLETE OR C13E9-00/C13EB-00 UNABLE TO ERASE This bulletin applies only to vehicles equipped with Direct Adaptive Steering (DAST). SERVICE INFORMATION This bulletin has information for two services for which a technician may need additional help: - While performing DAST CALIBRATION (MODE1), the calibration may stop or will not start. - DTC C13E9-00 (BOOTING ANGLE PROCESSING) and C13EB-00 (BOOTING ANGLE PROCESSING) are stored and cannot be erased. The above conditions may indicate that DAST CALIBRATION (MODE1) was not performed correctly or was not completed correctly. Use the SERVICE PROCEDURE in this bulletin as an aid to correctly perform and complete DAST CALIBRATION MODE 1. NOTE: - The SERVICE PROCEDURE in this bulletin does not contain all of the required steps. - The Electronic Service Manual (ESM) must be used together with this bulletin. - This bulletin contains additional clarification as an aid to perform DAST CALIBRATION MODE 1.

The summaries are NHTSA's. Each bulletin's page links NHTSA's copy of the manufacturer's document.