WenmarOpen by Wenmar Pro

Service bulletins for the 2019 Hyundai Santa Fe

A bulletin is a manufacturer's communication to its dealers, as NHTSA indexes it. The summary is NHTSA's. The document is the manufacturer's: read it at NHTSA. A bulletin is not a recall, and listing a model year does not mean every vehicle of it is concerned.

184 on file from NHTSA, as of 2026-10-19.

By type

By component

By trouble code

By topic

Only bulletins with component: Electrical system are shown. Show all

Bulletins, newest first
19-AT-024H2019-12-16. Service bulletin. ELECTRICAL SYSTEM. If you are servicing a vehicle with the DTC or symptoms listed below, refer to the Service Procedure to diagnose the condition. ? Diagnostic trouble codes: ?P0705 - Range switch sensor circuit ?P0706 - Range switch range/performance ?P0707 - Range switch - open circuit ?P0708 - Range switch - short circuit or multiple inputs ? Symptoms: ?Malfunction Indicator Light (MIL) illuminated ?4th gear fail-safe ?No gear indication in cluster ?Intermittent no engine crank/no start in ?P? or ?N? with or without MIL or DTC.
19-01-006H-42019-11-18. Service bulletin. EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL; ELECTRICAL SYSTEM:WIRING. Applicable vehicles with 2.0L Turbo and 2.4L GDI engines may experience the Check Engine warning lamp illuminated with DTC P1326. Follow the procedure to inspect the vehicle and install a wire harness extension and/or replacement engine based on the inspection results.
19-01-002H-42019-11-18. Service bulletin. ELECTRICAL SYSTEM:SOFTWARE; ENGINE. Hyundai is conducting a product improvement campaign to enhance the knock sensor software to detect abnormal engine bearing noise before potentially severe engine damage occurs. If abnormal engine bearing noise is detected, the Malfunction Indicator Lamp (MIL) will blink continuously, a chime will sound on certain vehicles, and the vehicle will be placed in Engine Protection Mode allowing the customer to drive to the nearest Hyundai dealer for diagnosis and repair. In addition, DTC P132600 will be recorded in the ECM. The vehicle can continue to be operated for a limited time in Engine Protection Mode, but it will accelerate slower and have a reduced maximum speed. Engine RPMs will be limited to approximately 1800-2000 RPM.
Campaign 953 Dea2019-11-18. Service bulletin. EQUIPMENT ADAPTIVE/MOBILITY; ELECTRICAL SYSTEM:SOFTWARE; ENGINE; EQUIPMENT. Hyundai has developed a new engine monitoring technology called a Knock Sensor Detection System (KSDS). The technology uses software innovations and leverages existing engine sensors to continuously monitor for symptoms that may precede an engine failure.
Campaign T3G Dea2019-11-18. Service bulletin. ENGINE; EQUIPMENT ADAPTIVE/MOBILITY; EQUIPMENT; ELECTRICAL SYSTEM. Hyundai has launched a Service Campaign for applicable vehicles with 2.0L Turbo and 2.4L GDI engines that may experience the Check Engine warning lamp illuminated with DTC P132600.
19-AT-019H2019-09-30. Service bulletin. ENGINE; EQUIPMENT; ELECTRICAL SYSTEM. If you are servicing an applicable vehicle with a ?Check Engine? light on and one or more of the DTC listed below, follow the repair procedure and replace the related oil pressure harness with integrated oil temperature sensor.
19-AT-017H2019-09-30. Service bulletin. ENGINE AND ENGINE COOLING; ELECTRICAL SYSTEM:STARTER ASSEMBLY:SOLENOID. If you are servicing an applicable vehicle with a ?Check Engine? light on and one or more of the DTC listed below, follow the repair procedure and replace the related solenoid and oil pressure harness.
19-BE-008H2019-07-01. Service bulletin. ELECTRICAL SYSTEM; LANE DEPARTURE; FORWARD COLLISION AVOIDANCE. This bulletin provides information for replacement of the Blind-Spot Collision Warning (BCW) module. Whenever the left or right side BCW module is being replaced, it is required to perform the variant coding procedure. If the variant coding procedure is not performed, a DTC C1743 (S/W mismatch) will be triggered.
19-FL-003H2019-05-20. Service bulletin. POWER TRAIN; ELECTRICAL SYSTEM. This bulletin provides the procedure to write the Vehicle Identification Number (VIN) during the replacement of the Engine Control Module (ECM) or Powertrain Control Module (PCM). Once the VIN has been programmed to the ECM/PCM, it cannot be removed or overwritten.
19-FL-002H2019-04-22. Service bulletin. ELECTRICAL SYSTEM. This bulletin describes the Santa Fe (TM) Idle Stop and Go (ISG) system operations and battery sensor recalibration procedure. Refer to applicable Work Shop Manual and Owner?s Manual for additional information
5NP-T3D4X-012019-02-19. Service bulletin. ELECTRICAL SYSTEM. This bulletin provides information related to the Engine Control Module (ECM) and Electronic Stability Control (ESC) software updates for certain 2019MY Santa Fe (TM) equipped with 2.4L engine. The ECM update is revised for starting performance and Idle Stop & Go (ISG) control logic. In addition, the ESC update is revised for hold timing of Hill-start Assist Control (HAC) function to optimized ISG operation.
5NP-X7C8Z-012019-02-19. Service bulletin. ELECTRICAL SYSTEM. Hyundai Motor America is conducting a Service Campaign to update the ECM & ESC on certain 2019 model year Santa Fe 2.4L vehicles. Service Campaign T3M provides a service procedure to update the ECM & ESC software.

The summaries are NHTSA's. Each bulletin's page links NHTSA's copy of the manufacturer's document.