WenmarOpen by Wenmar Pro

Service bulletins for the 2016 GMC Yukon

A bulletin is a manufacturer's communication to its dealers, as NHTSA indexes it. The summary is NHTSA's. The document is the manufacturer's: read it at NHTSA. A bulletin is not a recall, and listing a model year does not mean every vehicle of it is concerned.

1848 on file from NHTSA, as of 2026-10-19.

By type

By component

By trouble code

By topic

Bulletins, newest first
PIC3100F2017-12-14. Service bulletin. ELECTRICAL SYSTEM: INSTRUMENT CLUSTER/PANEL. This Preliminary Information communication provides information to the technician about vehicle's odometer appears to be inaccurate relative to a known distance traveled. Technician should obtain a hand-held GPS unit to test the odometer. If a hand held GPS unit is not available, the only other option is to verify the miles traveled using a surveyor's wheel or a dynamometer.
PIT5291C2017-12-14. Service bulletin. EXTERIOR LIGHTING:TAIL LIGHTS. This Preliminary Information communication provides information to the technician about vehicle that may have wind whistle noise heard from the right or left rear quarter glass area when driving at highway speeds or with a cross wind. Technician will inspect the quarter glass for excessive urethane. If excessive urethane is found use a sharp knife and cut off the excessive urethane. Also the technician will install foam tape along the entire length of the tail light assembly.
PIP55312017-12-14. Service bulletin. ENGINE; POWER TRAIN. This Preliminary Information communication provides information to the technician on the steps need to diagnose and repair vehicles that may have stalling shudder and/or hard shifting into 1st gear or reverse vibration on launch (with excessive crankshaft end play). Technician will test to determine if the crank shaft end play is within specification 0.0015–0.0086 inch. If end play is found to be out of specification, remove engine and inspect for possible crankshaft thrust bearing and/or crankshaft for wear. Inspect thrust bearing for wear on one side and crankshaft on that “mating” surface. If the thrust bearing has three vertical channels worn off replace connecting rod bearings, main bearings, thrust bearing and crankshaft. If working on a Corvette the oil tank with lines and oil cooler are both required to be replaced if equipped
PIP5498C2017-11-14. Service bulletin. ENGINE AND ENGINE COOLING:EXHAUST SYSTEM. This Preliminary information communicatesA vehicle may have a concern ofDTCP050D settingalongwith a P0300 after a cold start up. White smoke and/or coolant odor may come from exhaust for an extended period of time at cold start as well. CauseCoolant getting into the cylinders, and provides direction for the repair.
PIT3946B2017-11-14. Service bulletin. EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL; EQUIPMENT. This Preliminary Information communicates an issues with the headliner sagging and how to reattachthe velcrousing Hardman Double Bubble Epoxy part number 04001.
PIT5288F2017-11-14. Service bulletin. ELECTRICAL SYSTEM; EQUIPMENT. This Preliminary Information communication provides information to the technician about vehicles that may have any of these concerns remote keyless entry, passive Entry and Start Inoperative, No Fob detect message on driver information center, service tire pressure system, no audio, touch screen Inoperative, Steering Wheel Controls Inoperative, Service Stabilitrak, rear power windows inoperative, rear wiper inoperative, and or a dead battery. Technician may find Diagnostic Trouble Codes B3101, B144C, C0710, C0544, U1548, U1549, U154A, U0151, U0126, U0415, U0077, U0028 and/or U0029. Technician should inspect the left instrument panel for the wire harness being pinched. Technician will need to repair the wire harness and reroute the wire harness.
PIP55262017-11-14. Service bulletin. EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL. This Preliminary Information communication advises the technician that the Product Quality Center has a part restriction for the 8L45 and 8L90 park actuator rod. The dealer technician is advised to call the GM Product Quality Center for further assistance.
PIP5411F2017-11-14. Service bulletin. FUEL SYSTEM, GASOLINE:DELIVERY:FUEL PUMP; ELECTRICAL SYSTEM. This Preliminary Information communication provides information to the technician about vehicles that may have hesitation or a stalling condition while in ambient temperatures 100 degrees or higher. Technician may find Diagnostic Trouble Codes P2635 and or P018B set. The dealer is advised to replace the in tank fuel pump module assembly to correct the condition.
PIC5650C2017-11-14. Service bulletin. EQUIPMENT; ELECTRICAL SYSTEM. This Preliminary Information communication provides information to the technician about vehicles that have an intermittent no crank, no start, or start stall concern with the security light coming on. Technician may find Diagnostic Trouble Codes B3055, B3060, and/or B3935. Technician should not replace any parts for this concern. If unable to duplicate the concern ask if the customer uses any Radio Frequency Identification Devices when the concern is present. Dealer should also direct their customers to the appropriate section in the Owner manuals that references that the device complies.
PIP5411E2017-11-14. Service bulletin. ELECTRICAL SYSTEM:SOFTWARE. This Preliminary Information communication provides information to the technician about vehicles that may have hesitation or a stalling condition while in ambient temperatures 100 degrees or higher. Technician may find Diagnostic Trouble Codes P2635 and or P018B set. The dealer is advised to replace the in tank fuel pump module assembly to correct the condition. Dealer directed to follow latest version of PIP5507 if the fuel pump does not correct the concern.
PIC5492F2017-11-14. Service bulletin. ELECTRICAL SYSTEM:SOFTWARE. This Preliminary Information communication provides information to the technician about vehicles that have a Diagnostic Trouble Code B101D-37 history in the Vehicle Communication Interface Module or telematics communication interface control module. Engineering has determined that this code will only display in history on the scan tool and will not cause issues with OnStar system operation.
PIT5353B2017-11-14. Service bulletin. EQUIPMENT; ELECTRICAL SYSTEM; EQUIPMENT:ELECTRICAL:RADIO/TAPE DECK/CD ETC.. This Preliminary Information communication provides information to the technician about what XM offerings are available for vehicles. A dealer or customer can access the website listed below for vehicle specific XM offerings and availability.
PIT5206F2017-11-14. Service bulletin. ELECTRICAL SYSTEM. This Preliminary Information communication provides information to the technician with the steps on diagnosing and repairing vehicles that may have unwanted grade braking, reduced engine power with no Driver Information Center messages “ Brake Pedal Override Feature “, transmission busy or frequent shifting up or down, and Diagnostic Trouble Codes P057B, P057C, and/or P057D may or may not be set. Technician will use this preliminary information to find the brake pedal position data parameters in the scan tool, and also to provide some additional diagnostic help. These issues may be caused by an incorrect brake pedal position sensor input to the engine control module. Technician will verify with the scan tool if the engine control module has the correct parameters for the brake pedal position sensor. If an engine control module brake pedal position sensor relearn is performed, the truck may be temporarily repaired until the intermittent wiring issue between the engine control module and brake pedal position sensor occurs again. On 2014 and newer trucks inspect and repair any damage to X115 and X119. On the 2014 and previous trucks inspect and repair any damage to X205.
PIT5533A2017-11-14. Service bulletin. SUSPENSION. This Preliminary Information communication provides information to the technician about vehicles that have a creak, click, pop, and or crack type noise from the front suspension or front frame area while making tight turns. Technician will need to loosen and then re-torque the four front frame cross member nuts and bolts.
PIP5211F2017-10-15. Service bulletin. SUSPENSION. This Preliminary Information communication provides information to the technician the steps needed to diagnose and repair vehicles with a rough idle and/or vibration at idle in Drive. This condition will not be present in Park, or Neutral. This concern may be caused by ground out within the one or both engine mounts. Technician will use CH-51450-A (Pico Oscilloscope) to measure the vibration disturbance. If the vibration concern is E1.5 in the horizontal / lateral direction with Pico sensor mounted in seat track as indicated ? continue with steps to reduce the amplitude of the vibration by adding spacers in key locations to reduce ground out within the engine mounts. The 6.2L engine has a characteristic E1 which can be felt, and may be described as a lopey idle. Do not confuse 6.2L E1 characteristic (not caused by mount ground-out), with E1.5 normal idle characteristics being transmitted into the truck via ground-out thru the engine mounts. If measuring high at the seat track 12 mg or greater; replacement of the engine mounts should help reduce the amplitude of the vibration. If the disturbance measures at the seat track as E1.5 lateral in the range of approximately 2.5 - 8 mg using a tri-axis sensor. Then place tri-axis Pico sensor on the inboard seat track forward-most location to record measurement of the rough idle vibration concern. With the Heater-Vent-Air Conditioning on perform several short heavy launch events from stop to stop to bring the temperatures back up while attempting to re-create the rough idle vibration in Drive with Pico sensor placed on inboard seat track; while the vibration is active ? Record Pico reading. This method seems to provide better results than extended test drives. If the Pico reading for E1.5, with vibration active, at specified seat track location measures close to 2mg or less use Service Information to diagnose rough idle / vibration. If the Pico reading for E1.5, with vibration active, at the inboard forward seat track l
PIT5236H2017-10-15. Service bulletin. ELECTRICAL SYSTEM:SOFTWARE. This Preliminary Information communication provides information to the technician about vehicles that have a Diagnostic Trouble Code B101D stored in Telematics Communication Interface Control Module. Technician will use Global Diagnostic System 2 to review the Firmware Over-the-Air version and the OnStar Customer Identifier and contact General Motors Technical Assistance Center for further assistance.
PIC6201A2017-10-15. Service bulletin. ELECTRICAL SYSTEM. This Preliminary Information communication provides the technician with the steps needed to diagnose and repair a vehicle with Wi-Fi or Bluetooth inoperative or poor performance concern. Technician will need to obtain data from Global Diagnostics Services 2 and call General Motors Technical Assistance Center for further assistance. Technician should be advised that concern only applies to OnStar Wi-Fi Regular Production Option Code (VV4) and Bluetooth Regular Production Option Code (UPF).
PIT5284C2017-10-15. Service bulletin. SEATS. This Preliminary Information communication provides information to the technician on how to diagnose and repair vehicles that may have a rattle noise from the second row seat. Technician will need to inspect the striker not aligned properly in latch opening. To repair this condition, rework/adjust the striker in the direction to center it in the latch opening. An adjustable wide mouth metal working tool may be used to adjust the striker just enough to center in the latch opening. Technician may find a seat bottom latch may have an unequal latch opening side-to-side for the striker to seat into. To repair this condition, with the affected seat in the tumbled forward position, while applying steady, firm pressure, cycle the seat down into the latched position. Some vehicles built prior to 09/21/2015 with 60/40 Split Bench Seat may have 60-percent long side bench, inboard latch may not be properly aligned in striker opening. Technician will need to place a 2.6 mm thick flat washer over the 40 percent seat base stud, not the floor stud. Some vehicles may have a seat base plat that rattles against the rib in the floor pan. Apply Mylar tape to the floor pan under the seat plate to provide relief for the rattle condition.
PIT5307E2017-10-15. Service bulletin. EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL. This Preliminary Information communication provides information to the technician about vehicles that may have a service engine soon malfunction indicator lamp, antilock braking system malfunction indicator lamp, service suspension system message, misfire, hesitation, no crank, heater-vent-air conditioning inoperative. Technician may find F11UA, F104UA, F35UA, and or F60UA blown. Technician should inspect the engine harness near the vacuum pump pulley to be chafing. Technician will need to reroute the wire harness and repair and damaged wires.
PIP5337F2017-10-15. Service bulletin. POWER TRAIN:AUTOMATIC TRANSMISSION:TORQUE CONVERTER. This Preliminary Information communication provides information to the technician on the step to diagnose and repair the vehicles that may have a shake or shudder during light throttle acceleration, between 30 and 65 mph steady state driving. Also shudder feeling that may be described as driving over rumble strips or rough pavement. Technician will drive the vehicle and monitor the torque converter clutch slip. The torque converter clutch slip speed should be 10 rpm or less also note if the shudder takes place during torque converter clutch apply. If the torque converter clutch slip speed is in the range of 10 RPM or less the condition is possibly related to engine performance. If the shudder is only present in 4 cylinder mode and torque converter clutch slip is 10 rpm or less deem the shudder concern normal characteristic of Active Fuel Management. If the slip speed is beyond 10 rpm or there is shudder during torque converter clutch apply the torque converter will need to be replaced. Also flush the cooler lines and cooler using DT-45096 transmission oil cooling system flush and flow test tool.
PIC6216A2017-10-15. Service bulletin. ELECTRICAL SYSTEM. This Preliminary Information communication provides information to the technician about vehicles voice recognition inoperative for calling Bluetooth phone contacts. Technician will need to Clear All Private Data and repair any phones that were deleted.
PIC6033A2017-10-15. Service bulletin. ELECTRICAL SYSTEM:SOFTWARE. This Preliminary Information communication provides information to the technician about vehicles that may have "Service Theft System" message on the Driver Information Center. Technician may find Diagnostic Trouble Code B291B sym 3B and is unable to clear the Diagnostic Trouble Code. Technician will need to restore communication between the Body Control Module and Theft Deterrent Sensor Module to clear the Diagnostic Trouble Code.
PIP5411C2017-10-15. Service bulletin. ELECTRICAL SYSTEM; FUEL SYSTEM, GASOLINE. This Preliminary Information communication provides information to the technician about vehicles that may have hesitation or a stalling condition while in ambient temperatures 100 degrees or higher. Technician may find Diagnostic Trouble Codes P2635 and or P018B set. The dealer is advised to replace the in tank fuel pump module assembly to correct the condition.
PIT5232C2017-10-15. Service bulletin. ELECTRICAL SYSTEM:12V/24V/48V BATTERY. This Preliminary Information communication provides information to the technician the steps to diagnose and repair the concern of the display is showing 32° F (0° C) after a battery or reprogramming a module. The outside temperature will begin to update if driven above 20 mph for at least 5 minutes. If the vehicle speed drops below 20 mph, the timer will reset and the display will stop updating. Once the display starts to update it may take several more minutes of driving above 20 mph for the display to fully update. Also if the vehicle is shut off for more than 8 hours the display will update when the ignition is turned on.
PIC6186D2017-10-15. Service bulletin. EQUIPMENT:ELECTRICAL:RADIO/TAPE DECK/CD ETC.. This Preliminary Information communication provides information to the technician about vehicles that the radio will turn on unwanted after a key cycle when the radio was shut off before the key was turned off. Dealer should communicate to the customer that we apologize for this inconvenience and that General Motors is working on a solution for this concern.

The summaries are NHTSA's. Each bulletin's page links NHTSA's copy of the manufacturer's document.