Service bulletins for the 2016 GMC Yukon
A bulletin is a manufacturer's communication to its dealers, as NHTSA indexes it. The summary is NHTSA's. The document is the manufacturer's: read it at NHTSA. A bulletin is not a recall, and listing a model year does not mean every vehicle of it is concerned.
1848 on file from NHTSA, as of 2026-10-19.
By type
By component
By trouble code
By topic
Only bulletins with component: Engine are shown. Show all
| PIT5447A | 2017-03-23. Service bulletin. EQUIPMENT; ENGINE AND ENGINE COOLING:EXHAUST SYSTEM:MANIFOLD/HEADER/MUFFLER/TAIL PIPE. THIS PRELIMINARY INFORMATION COMMUNICATION PROVIDES INFORMATION TO THE TECHNICIAN ON THE STEPS NEEDED TO DIAGNOSE AND REPAIR VEHICLES THAT MAY HAVE A RATTLE NOISE FROM THE DASH. TECHNICIAN WILL NEED TO INSPECT FOR THE REAR HEATER PIPES CONTACTING THE PASSENGER SIDE EXHAUST MANIFOLD. IF THE REAR HEATER PIPE IS FOUND TO BE CONTACTING THE EXHAUST MANIFOLD, REPOSITION THE HEATER PIPE SO IT NO LONGER MAKES CONTACT. |
|---|---|
| PIP5337B | 2017-03-21. Service bulletin. ENGINE; POWER TRAIN:AUTOMATIC TRANSMISSION:TORQUE CONVERTER. THIS PRELIMINARY INFORMATION COMMUNICATION PROVIDES INFORMATION TO THE TECHNICIAN ON THE STEP TO DIAGNOSE AND REPAIR THE VEHICLES THAT MAY HAVE A SHAKE OR SHUDDER DURING LIGHT THROTTLE ACCELERATION, BETWEEN 30 AND 65 MPH STEADY STATE DRIVING. ALSO SHUDDER FEELING THAT MAY BE DESCRIBED AS DRIVING OVER RUMBLE STRIPS OR ROUGH PAVEMENT. TECHNICIAN WILL DRIVE THE VEHICLE AND MONITOR THE TORQUE CONVERTER CLUTCH SLIP. THE TORQUE CONVERTER CLUTCH SLIP SPEED SHOULD BE 10 RPM OR LESS ALSO NOTE IF THE SHUDDER TAKES PLACE DURING TORQUE CONVERTER CLUTCH APPLY. IF THE TORQUE CONVERTER CLUTCH SLIP SPEED IS IN THE RANGE OF 10 RPM OR LESS THE CONDITION IS POSSIBLY RELATED TO ENGINE PERFORMANCE. IF THE SHUDDER IS ONLY PRESENT IN 4 CYLINDER MODE AND TORQUE CONVERTER CLUTCH SLIP IS 10 RPM OR LESS DEEM THE SHUDDER CONCERN NORMAL CHARACTERISTIC OF ACTIVE FUEL MANAGEMENT. IF THE SLIP SPEED IS BEYOND 10 RPM OR THERE IS SHUDDER DURING TORQUE CONVERTER CLUTCH APPLY THE TORQUE CONVERTER WILL NEED TO BE REPLACED. |
| PIP5230C | 2017-03-21. Service bulletin. ENGINE. THIS PRELIMINARY INFORMATION COMMUNICATION ADVISES THE TECHNICIAN BEFORE REPLACING THE CRANKSHAFT TO REVIEW THE FOLLOWING. DEALER SHOULD COMPLETE THE SERVICE INFORMATION DIAGNOSTICS AND THE COST COMPARISON WORKSHEET FOR ASSEMBLY REPAIR VS REPLACEMENT. TECHNICIAN WILL USE THE LATEST VERSION OF 09-06-04-026G TO VERIFY THE ECM CALIBRATION IS NOT AN AFTERMARKET CALIBRATION. IF THE CUSTOMER PREFERS TO KEEP THE ORIGINAL NUMBERS MATCHING ENGINE PLEASE CALL TAC FOR REPAIR DIRECTION. |
| PIP5189A | 2017-03-20. Service bulletin. ENGINE AND ENGINE COOLING:EXHAUST SYSTEM:EMISSION CONTROL:CATALYTIC CONVERTOR. THIS PRELIMINARY INFORMATION COMMUNICATION PROVIDES INFORMATION TO THE TECHNICIAN ABOUT VEHICLE THAT MAY HAVE BLACK SMOKE ON A COLD START. A DUAL-PULSE INJECTION STRATEGY IS UTILIZED DURING ENGINE COLD START TO REDUCE THE TIME REQUIRED TO BRING THE CATALYTIC CONVERTER UP TO OPERATING TEMPERATURE. THIS SPLIT INJECTION STRATEGY LASTS FOR ABOUT 60 SECONDS ON COLD START. THIS PROCESS MAY CAUSE THE CUSTOMER TO SEE INCREASED BLACK SMOKE DURING COLD START AND SHOULD BE CONSIDERED NORMAL. |
| PIP5130G | 2017-03-20. Service bulletin. FUEL SYSTEM, GASOLINE:FUEL INJECTION SYSTEM:FUEL RAIL; ENGINE. THIS PRELIMINARY INFORMATION COMMUNICATION PROVIDES INFORMATION TO THE TECHNICIAN HOW TO DIAGNOSE AND REPAIR A VEHICLE WITH AN ENGINE THAT RUNS WITH AN INTERMITTENT CRANK NO START WITH A DIAGNOSTIC TROUBLE CODE P0011 OR P00C6 CURRENT OR HISTORY. THE CAMSHAFT POSITION ACTUATOR SOLENOID VALVE MAY BE STICKING OR BINDING CAUSING THE VALVE TIMING TO BE RETARDED. DEALER WILL NEED TO CYCLE THE CAMSHAFT POSITION ACTUATOR SOLENOID VALVE BY ENERGIZING IT USING GLOBAL DIAGNOSTIC SYSTEM 2. |
| PIP5308A | 2016-11-03. Service bulletin. ELECTRICAL SYSTEM; ENGINE. THIS PRELIMINARY INFORMATION COMMUNICATION ADVISES THE TECHNICIAN ON THE STEPS TO DIAGNOSE AND REPAIR THE CONCERN OF THE SERVICE ENGINE SOON LIGHT IS ON, AND THE ENGINE HAS LOW OIL PRESSURE. |
| PIP5382B | 2016-11-03. Service bulletin. ENGINE. THIS PRELIMINARY INFORMATION COMMUNICATION HAS THE STEPS FOR DIAGNOSING THE CONCERN OF EXCESSIVE OIL CONSUMPTION FOR THE GENERATION 5 ENGINE. DIAGNOSTIC INFORMATION IS PROVIDED FOR THE TECHNICIAN TO GATHER PRIOR TO CONTACTING THE PRODUCT QUALITY CENTER FOR FURTHER ASSISTANCE. |
| PIP5189B | 2016-11-01. Service bulletin. ELECTRICAL SYSTEM; ENGINE. THIS PRELIMINARY INFORMATION COMMUNICATION ADVISES THE TECHNICIAN ON THE STEPS TO DIAGNOSE AND REPAIR THE CONCERN OF BLACK SMOKE WHEN STARTING THE VEHICLE AFTER SITTING. |
| PIT5467A | 2016-10-24. Service bulletin. ENGINE. THIS PRELIMINARY INFORMATION COMMUNICATION PROVIDES INFORMATION TO THE TECHNICIAN ABOUT VEHICLES THAT THE ENGINE IDLE HOURS ARE INCORRECT HOWEVER THE ENGINE HOURS ARE CORRECT IN THE INSTRUMENT PANEL CLUSTER. TECHNICIAN WILL NEED TO CONTACT TECHLINE CUSTOMER SUPPORT CENTER TO REPROGRAM THE INSTRUMENT PANEL CLUSTER. |
| PIT5307D | 2016-10-21. Service bulletin. ENGINE; ELECTRICAL SYSTEM; SUSPENSION. THIS PRELIMINARY INFORMATION COMMUNICATION PROVIDES INFORMATION TO THE TECHNICIAN ABOUT VEHICLES THAT MAY HAVE A SERVICE ENGINE SOON MALFUNCTION INDICATOR LAMP, ANTILOCK BRAKING SYSTEM MALFUNCTION INDICATOR LAMP, SERVICE SUSPENSION SYSTEM MESSAGE, MISFIRE, HESITATION, NO CRANK, HEATER-VENT-AIR CONDITIONING INOPERATIVE. TECHNICIAN MAY FIND F11UA, F104UA, F35UA, AND OR F60UA BLOWN. TECHNICIAN SHOULD INSPECT THE ENGINE HARNESS NEAR THE VACUUM PUMP PULLEY TO BE CHAFING. TECHNICIAN WILL NEED TO REROUTE THE WIRE HARNESS AND REPAIR AND DAMAGED WIRES. |
| PIP5411A | 2016-10-21. Service bulletin. ENGINE. THIS PRELIMINARY INFORMATION COMMUNICATION PROVIDES INFORMATION TO THE TECHNICIAN ABOUT VEHICLES THAT MAY HAVE HESITATION OR A STALLING CONDITION WHILE IN AMBIENT TEMPERATURES 100 DEGREES OR HIGHER. TECHNICIAN MAY FIND DIAGNOSTIC TROUBLE CODES P2635 AND OR P018B SET. DEALER SHOULD COMMUNICATE TO THE CUSTOMER THAT WE APOLOGIZE FOR THIS INCONVENIENCE AND THAT GENERAL MOTORS IS WORKING ON A SOLUTION FOR THIS CONCERN. IF WORKING ON POLICE PURSUIT VEHICLES REGULAR PRODUCTION OPTION CODE PPV OR FLEET VEHICLES REGULAR PRODUCTION OPTION CODE FLT, CONTACT THE GENERAL MOTORS TECHNICAL ASSISTANCE CENTER FOR FURTHER ASSISTANCE. |
| PIP5382C | 2016-10-20. Service bulletin. ENGINE. THIS PRELIMINARY INFORMATION COMMUNICATION ADVISES THE TECHNICIAN THAT GENERATION 5 ENGINES WITH REGULAR PRODUCTION OPTION CODE L83, L86, OR LV3 MAY HAVE AN OIL CONSUMPTION CONCERN WERE ONE QUART IN 2000 MILES IS BEING USED. DEALER WILL CONFIRM OIL LEVEL WAS PROPERLY CHECKED PER OWNER’S MANUAL, AND CHECK THE BOLT TORQUE ON THE VALVE LIFTER OIL MANIFOLD ASSEMBLY, BEFORE YOU CONTACTING GENERAL MOTORS PRODUCT QUALITY CENTER. |
| PIP5337E | 2016-10-20. Service bulletin. ENGINE. THIS PRELIMINARY INFORMATION COMMUNICATION PROVIDES INFORMATION TO THE TECHNICIAN ON THE STEPS TO DIAGNOSE AND REPAIR THE VEHICLES THAT MAY HAVE A SHAKE OR SHUDDER DURING LIGHT THROTTLE ACCELERATION, BETWEEN 30 AND 65 MPH STEADY STATE DRIVING. ALSO SHUDDER FEELING THAT MAY BE DESCRIBED AS DRIVING OVER RUMBLE STRIPS OR ROUGH PAVEMENT. TECHNICIAN WILL DRIVE THE VEHICLE AND MONITOR THE TORQUE CONVERTER CLUTCH SLIP. THE TORQUE CONVERTER CLUTCH SLIP SPEED SHOULD BE 10 RPM OR LESS ALSO NOTE IF THE SHUDDER TAKES PLACE DURING TORQUE CONVERTER CLUTCH APPLY. IF THE TORQUE CONVERTER CLUTCH SLIP SPEED IS IN THE RANGE OF 10 RPM OR LESS THE CONDITION IS POSSIBLY RELATED TO ENGINE PERFORMANCE. IF THE SHUDDER IS ONLY PRESENT IN 4 CYLINDER MODE AND TORQUE CONVERTER CLUTCH SLIP IS 10 RPM OR LESS DEEM THE SHUDDER CONCERN NORMAL CHARACTERISTIC OF ACTIVE FUEL MANAGEMENT. IF THE SLIP SPEED IS BEYOND 10 RPM OR THERE IS SHUDDER DURING TORQUE CONVERTER CLUTCH APPLY THE TORQUE CONVERTER WILL NEED TO BE REPLACED. |
| PIP4786C | 2016-10-20. Service bulletin. ENGINE AND ENGINE COOLING. THIS PRELIMINARY INFORMATION COMMUNICATION PROVIDES INFORMATION TO THE TECHNICIAN ABOUT VEHICLES THAT MAY HAVE LOW OIL PRESSURE MESSAGE. TECHNICIAN MAY ALSO FIND A DIAGNOSTIC TROUBLE CODE P0521 IN THE ENGINE CONTROL MODULE. TECHNICIAN SHOULD FOLLOW ALL PUBLISHED SERVICE INFORMATION DIAGNOSIS. WHEN USING A SCAN TOOL IF THE OIL PRESSURE IS LOW BUT THE OIL PRESSURE AT THE OIL FILTER HOUSING IS CORRECT, TECHNICIAN SHOULD INSPECT THE VALVE LIFTER OIL FILTER FOR DEBRIS/SLUDGE THAT COULD BE RESTRICTING OIL FLOW TO THE OIL PRESSURE SENSOR. TECHNICIAN SHOULD REMOVE THE VALVE LIFTER OIL FILTER AND CLEAN IT. IF THE VALVE LIFTER OIL FILTER CANNOT BE CLEANED REPLACE IT. |
| PI1394A | 2016-10-19. Service bulletin. ENGINE. THIS INFORMATIONAL BULLETIN PROVIDES ADDITIONAL INFORMATION ON HOW TO INSTALL PISTONS AND SUGGEST WHAT TOOLS TO USE. |
| 030604017I | 2016-10-18. Service bulletin. ENGINE AND ENGINE COOLING:ENGINE:DIESEL. THIS INFORMATIONAL BULLETIN EXPLAINS THE USE OF DIESEL FUEL ADDITIVES IN AN ENGINE, ARE NOT REQUIRED UNLESS THE CUSTOMER DESIRES ADDITIVES TO PREVENT FUEL CONCERNS DEPENDING ON FUEL OR TEMPERATURE RELATED CONDITIONS. |
| 030603004R | 2016-10-18. Service bulletin. ENGINE; ELECTRICAL SYSTEM:12V/24V/48V BATTERY. THIS INFORMATIONAL BULLETIN PROVIDES INFORMATION ON HOW TO TEST A BATTERY AND WHAT IS NEEDED TO WARRANTY A BATTERY. |
| 000601026I | 2016-10-18. Service bulletin. ENGINE. THIS INFORMATIONAL BULLETINS PROVIDES INFORMATION ON THE INTAKE MANIFOLD INSPECTION/REPLACEMENT AFTER SERVERE INTERNAL ENGINE DAMAGE. |
| 000601012F | 2016-10-18. Service bulletin. ENGINE. THIS INFORMATIONAL BULLETIN PROVIDES INFORMATION TO GM DEALERS ON THE CORRECT CLEANING METHODS WHEN CLEANING ENGINE GASKET SEALING SURFACES. |
| 16NA249 | 2016-10-14. Service bulletin. ENGINE AND ENGINE COOLING. THIS INFORMATIONAL BULLETIN EXPLAINS A POSSIBLE NORMAL WHINING NOISE FROM THE BALANCE SHAFT CHAIN IF THE VEHICLE HAS LESS THAN 10,000 MILES ON IT. |
| PIP5395A | 2016-09-27. Service bulletin. FUEL SYSTEM, GASOLINE:DELIVERY:HOSES, LINES/PIPING, AND FITTINGS; FUEL SYSTEM, GASOLINE:DELIVERY:FUEL PUMP; ENGINE. THIS PRELIMINARY INFORMATION COMMUNICATION PROVIDES INFORMATION TO THE TECHNICIAN ON HOW TO DIAGNOSE AND REPAIR VEHICLES THAT MAY HAVE RATTLE OR TICKING NOISE THAT IS LOUDER INSIDE THE VEHICLE THAN OUTSIDE. THE NOISE MAY ALSO SOUND LIKE A LIFTER TICK. IF THE NOISE IS HEARD BEST AT THE FUEL LINE AND THE SOUND WILL BE REAL LOUD WITH A STETHOSCOPE. THE FUEL LINE WILL NEED TO BE REPLACED. |
| PIP5407 | 2016-09-21. Service bulletin. ENGINE. THIS PRELIMINARY INFORMATION COMMUNICATION PROVIDES INFORMATION TO THE TECHNICIAN ON HOW TO DIAGNOSE AND REPAIR VEHICLES THAT MAY HAVE DIAGNOSTIC TROUBLE CODE P06DD OR NO OR LOW OIL PRESSURE. TECHNICIAN WILL REPLACE TIMING CHAIN TENSIONER GUIDE. IF OIL PUMP FACE IS DAMAGED AND OR WORN THRU REPLACE OIL PUMP. INSPECT BEARINGS FOR DAMAGE WEAR DUE TO DEBRIS FROM OIL PUMP. |
| PIP5211E | 2016-09-21. Service bulletin. ENGINE. THIS PRELIMINARY INFORMATION COMMUNICATION PROVIDES INFORMATION TO THE TECHNICIAN THE STEPS NEEDED TO DIAGNOSE AND REPAIR VEHICLES WITH A ROUGH IDLE AND/OR VIBRATION AT IDLE IN DRIVE. THIS CONDITION WILL NOT BE PRESENT IN PARK, OR NEUTRAL. THIS CONCERN MAY BE CAUSED BY GROUND OUT WITHIN THE ONE OR BOTH ENGINE MOUNTS. TECHNICIAN WILL USE CH-51450-A (PICO OSCILLOSCOPE) TO MEASURE THE VIBRATION DISTURBANCE. IF THE VIBRATION CONCERN IS E1.5 IN THE HORIZONTAL / LATERAL DIRECTION WITH PICO SENSOR MOUNTED IN SEAT TRACK AS INDICATED – CONTINUE WITH STEPS TO REDUCE THE AMPLITUDE OF THE VIBRATION BY ADDING SPACERS IN KEY LOCATIONS TO REDUCE GROUND OUT WITHIN THE ENGINE MOUNTS. THE 6.2L ENGINE HAS A CHARACTERISTIC E1 WHICH CAN BE FELT, AND MAY BE DESCRIBED AS A LOPEY IDLE. DO NOT CONFUSE 6.2L E1 CHARACTERISTIC (NOT CAUSED BY MOUNT GROUND-OUT), WITH E1.5 NORMAL IDLE CHARACTERISTICS BEING TRANSMITTED INTO THE TRUCK VIA GROUND-OUT THRU THE ENGINE MOUNTS. IF MEASURING HIGH AT THE SEAT TRACK 12 MG OR GREATER; REPLACEMENT OF THE ENGINE MOUNTS SHOULD HELP REDUCE THE AMPLITUDE OF THE VIBRATION. IF THE DISTURBANCE MEASURES AT THE SEAT TRACK AS E1.5 LATERAL IN THE RANGE OF APPROXIMATELY 2.5 - 8 MG USING A TRI-AXIS SENSOR. THEN PLACE TRI-AXIS PICO SENSOR ON THE INBOARD SEAT TRACK FORWARD-MOST LOCATION TO RECORD MEASUREMENT OF THE ROUGH IDLE VIBRATION CONCERN. WITH THE HEATER-VENT-AIR CONDITIONING ON PERFORM SEVERAL SHORT HEAVY LAUNCH EVENTS FROM STOP TO STOP TO BRING THE TEMPERATURES BACK UP WHILE ATTEMPTING TO RE-CREATE THE ROUGH IDLE VIBRATION IN DRIVE WITH PICO SENSOR PLACED ON INBOARD SEAT TRACK; WHILE THE VIBRATION IS ACTIVE – RECORD PICO READING. THIS METHOD SEEMS TO PROVIDE BETTER RESULTS THAN EXTENDED TEST DRIVES. IF THE PICO READING FOR E1.5, WITH VIBRATION ACTIVE, AT SPECIFIED SEAT TRACK LOCATION MEASURES CLOSE TO 2MG OR LESS USE SERVICE INFORMATION TO DIAGNOSE ROUGH IDLE / VIBRATION. |
| PIP5337D | 2016-09-21. Service bulletin. ENGINE; POWER TRAIN:AUTOMATIC TRANSMISSION:TORQUE CONVERTER. THIS PRELIMINARY INFORMATION COMMUNICATION PROVIDES INFORMATION TO THE TECHNICIAN ON THE STEP TO DIAGNOSE AND REPAIR THE VEHICLES THAT MAY HAVE A SHAKE OR SHUDDER DURING LIGHT THROTTLE ACCELERATION, BETWEEN 30 AND 65 MPH STEADY STATE DRIVING. ALSO SHUDDER FEELING THAT MAY BE DESCRIBED AS DRIVING OVER RUMBLE STRIPS OR ROUGH PAVEMENT. TECHNICIAN WILL DRIVE THE VEHICLE AND MONITOR THE TORQUE CONVERTER CLUTCH SLIP. THE TORQUE CONVERTER CLUTCH SLIP SPEED SHOULD BE 10 RPM OR LESS ALSO NOTE IF THE SHUDDER TAKES PLACE DURING TORQUE CONVERTER CLUTCH APPLY. IF THE TORQUE CONVERTER CLUTCH SLIP SPEED IS IN THE RANGE OF 10 RPM OR LESS THE CONDITION IS POSSIBLY RELATED TO ENGINE PERFORMANCE. IF THE SHUDDER IS ONLY PRESENT IN 4 CYLINDER MODE AND TORQUE CONVERTER CLUTCH SLIP IS 10 RPM OR LESS DEEM THE SHUDDER CONCERN NORMAL CHARACTERISTIC OF ACTIVE FUEL MANAGEMENT. IF THE SLIP SPEED IS BEYOND 10 RPM OR THERE IS SHUDDER DURING TORQUE CONVERTER CLUTCH APPLY THE TORQUE CONVERTER WILL NEED TO BE REPLACED. |
| PIP-5308-A | 2016-08-17. Service bulletin. ENGINE. THIS PRELIMINARY INFORMATION COMMUNICATION ADVISES THE TECHNICIAN ON THE STEPS TO DIAGNOSE AND REPAIR THE CONCERN OF THE SERVICE ENGINE SOON LIGHT IS ON, AND THE ENGINE HAS LOW OIL PRESSURE. |
The summaries are NHTSA's. Each bulletin's page links NHTSA's copy of the manufacturer's document.