Service bulletins for the 2015 GMC Yukon
A bulletin is a manufacturer's communication to its dealers, as NHTSA indexes it. The summary is NHTSA's. The document is the manufacturer's: read it at NHTSA. A bulletin is not a recall, and listing a model year does not mean every vehicle of it is concerned.
2691 on file from NHTSA, as of 2026-10-19.
By type
By component
By trouble code
By topic
Only bulletins with component: Engine are shown. Show all
| PIP5130F | 2017-08-15. Service bulletin. ENGINE; EQUIPMENT ADAPTIVE/MOBILITY. This Preliminary Information communication provides information to the technician how to diagnose and repair a vehicle with an engine that runs with an intermittent crank no start with a Diagnostic Trouble Code P0011 or P00C6 current or history. The Camshaft Position Actuator Solenoid Valve may be sticking or binding causing the valve timing to be retarded. Dealer will need to cycle the Camshaft Position Actuator Solenoid Valve by energizing it using Global Diagnostic System 2. |
|---|---|
| PIP5357 | 2017-08-15. Service bulletin. ENGINE; EQUIPMENT ADAPTIVE/MOBILITY. This Preliminary Information communication provides information to the technician about vehicles with engine oil consumption. If published Service Information for oil consumption with no fix. Remove the vacuum line from the back of the vacuum pump and inspect for oil. If oil is found then reference the latest version of PIT5361. |
| PIT4943D | 2017-08-15. Service bulletin. FUEL SYSTEM, GASOLINE; FUEL SYSTEM, OTHER:STORAGE:TANK ASSEMBLY; ENGINE AND ENGINE COOLING:EXHAUST SYSTEM:EMISSION CONTROL. This Preliminary Information communication provides information to the technician about vehicles that have a Service Engine Soon Malfunction Indicator Lamp. Technician may find Diagnostic Trouble Code P0442. Technician will need to review Techlink article from May 2013 titled "Using the Evaporative Emissions System Tester" Technician will need to follow these steps to help diagnose the issue. First after the P0442 has been verified do not disturb any of the fuel system components. The technician now can use the scan tool to close the Evaporative Emissions System. If possible change the tank pressure sensor units from inch_H2O to milimeter_Hg for better resolution. Now the vehicle can be stared to monitor the tank pressure sensor output value for approximately two minutes. If the tank pressure sensor value does change, pressurize the fuel tank side of the purge solenoid with the GE 41413-A / J 41413-A and the necessary adaptors. Now add smoke and allow pressure to stabilize for 2 minutes. If smoke is allowed to pass through the purge solenoid, replace the purge solenoid. If the tank pressure sensor value does not change, then install CH-48096 adaptor between the purge line from the canister and the purge solenoid. With the Evaporative Emissions System closed, pressurize the system through the CH-48096 adaptor and allow the system to completely stabilize, by observing the Press / Vac Gauge for a minimum of 5 minutes. Now add smoke to the system with GE 41413-A / J 41413-A after system stabilization. Now inspect the purge solenoid, engine side, fuel cap, canister vent solenoid filter and any line quick connects. When the leak is unable to be located, test under a vacuum condition. his type of leak may be detected by using the scan tool Purge/Seal function to create a vacuum in the Evaporative Emissions System and then observe the FTP sensor parameter for vacuum decay. |
| PIP5179B | 2017-08-15. Service bulletin. ENGINE; EQUIPMENT:MECHANICAL; FUEL SYSTEM, OTHER:FUEL INJECTION SYSTEM. This Preliminary Information communication provides information to the technician about vehicles that have extended or long crank time during cold ambient air temperatures. Direct Injection systems run at higher pressures, and the mechanical pump on the engine must build up the required pressure before the first injection event occurs. Direct Injection engines may have slightly longer cold crank times than that of port fuel engines. |
| PIP5199A | 2017-08-15. Service bulletin. ENGINE; EQUIPMENT ADAPTIVE/MOBILITY. This Preliminary Information communication provides information to the technician about vehicles with a crankshaft balancer appears to be out of balance or wobbling while watching it with the engine running. Technician will need to check crankshaft balancer run out. If the balancer run out is greater than 0.25mm the crankshaft balancer will need to be replaced. |
| PIT5202C | 2017-08-15. Service bulletin. ENGINE; POWER TRAIN; SERVICE BRAKES, HYDRAULIC:POWER ASSIST. This Preliminary Information communication provides information to the technician about vehicles that are equipped with 6L80 Regular Production Option Code (MYC), 6L90 Regular Production Option Code (MYD) or 8L90 Regular Production Option Code (M5U) Automatic Transmission. Starting with the 2013 model year, Full Size Trucks and Utilities now have Powertrain Grade Braking. Powertrain grade braking assists when driving on a downhill grade to help maintain desired vehicle speed by using the engine and transmission to slow the vehicle. |
| PIP5163B | 2017-08-15. Service bulletin. EQUIPMENT ADAPTIVE/MOBILITY; FUEL SYSTEM, GASOLINE; ENGINE. This Preliminary Information communication provides information to the technician about engine block that have a possible cylinder bore damage, scoring or out of round as the possible cause of engine oil consumption, misfire, cylinder leakage or blow by. Technician will need to inspect the engine for Cylinder damage or scoring, an out of round cylinder bore, Dirt intrusion, and Catalytic Converter failure. |
| PIP5442 | 2017-08-15. Service bulletin. ENGINE AND ENGINE COOLING:EXHAUST SYSTEM. This Preliminary Information communication provides information to the technician about vehicles that have an exhaust leak, noisy exhaust, or noise mid-vehicle. Technician will need to check for an unseated pipe to pipe mid-joint connection. Technician will need to install new exhaust band. |
| PIP5382F | 2017-08-15. Service bulletin. EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL; ENGINE. This Preliminary Information communication advises the technician that generation 5 engines with Regular Production Option Code L83, L86, or LV3 may have an oil consumption concern were one quart in 2000 miles is being used. Dealer will confirm oil level was properly checked per Owner?s Manual, and check the bolt torque on the Valve Lifter Oil Manifold Assembly, before you contacting General Motors Product Quality Center. |
| PIP5252 | 2017-08-15. Service bulletin. ENGINE. This Preliminary Information communication provides information to the technician about vehicles that the engine may run hot with the snow plow installed. Do not exceed 64?kilometers per hour / 40?miles per hour with a snow plow mounted to the vehicle even if equipped with VYU. The vehicle could overheat and be damaged. |
| PIP5211B | 2017-08-15. Service bulletin. ELECTRICAL SYSTEM; POWER TRAIN; EQUIPMENT ADAPTIVE/MOBILITY; ENGINE. This Preliminary Information communication provides information to the technician the steps needed to diagnose and repair vehicles with a rough idle and/or vibration at idle in Drive. This condition will not be present in Park, or Neutral. This concern may be caused by ground out within the one or both engine mounts. Technician will use CH-51450-A (Pico Oscilloscope) to measure the vibration disturbance. If the vibration concern is E1.5 in the horizontal / lateral direction with Pico sensor mounted in seat track as indicated ? continue with steps to reduce the amplitude of the vibration by adding spacers in key locations to reduce ground out within the engine mounts. The 6.2L engine has a characteristic E1 which can be felt, and may be described as a lopey idle. Do not confuse 6.2L E1 characteristic (not caused by mount ground-out), with E1.5 normal idle characteristics being transmitted into the truck via ground-out thru the engine mounts. If measuring high at the seat track 12 mg or greater; replacement of the engine mounts should help reduce the amplitude of the vibration. If the disturbance measures at the seat track as E 1.5 lateral in the range of approximately 2.5 - 8 mg using a tri-axis sensor. Then place tri-axis Pico sensor on the inboard seat track forward-most location to record measurement of the rough idle vibration concern. With the Heater-Vent-Air Conditioning on perform several short heavy launch events from stop to stop to bring the temperatures back up while attempting to re-create the rough idle vibration in Drive with Pico sensor placed on inboard seat track; while the vibration is active ? Record Pico reading. This method seems to provide better results than extended test drives. If the Pico reading for E1.5, with vibration active, at specified seat track location measures close to 2mg or less use Service Information to diagnose rough idle / vibration. If the Pico reading for E1.5, with vibration active, at the inboard forward seat track |
| PIP5029F | 2017-08-15. Service bulletin. ENGINE. This Preliminary Information communication provides information to the technician about vehicles that have a Malfunction Indicator Lamp on or engine misfire, rough idle, extended crank, or crank no start in some cases. Technician will need to perform published Service Information diagnostics. If technician finds carbon an upper engine and valve cleaning should be performed. |
| PIT5350 | 2017-08-15. Service bulletin. ENGINE; ELECTRICAL SYSTEM:SOFTWARE. This Preliminary Information communication advises the technician that there have been some reports that the current engine hours are not correct and display 0.0. Technician will need to program the Instrument Panel Cluster using Service Programming System. |
| PIT5448A | 2017-08-15. Service bulletin. ENGINE. This Preliminary Information communication advises the technician with a tip when the vehicle stops running after it has been idling for 2.5 hours. This is normal operation of the vehicle built with regular production code BTM. |
| PIP5230B | 2017-08-15. Service bulletin. ENGINE; EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL. This Preliminary Information communication advises the technician before replacing the crankshaft to review the following. Dealer should complete the Service Information diagnostics and the Cost Comparison Worksheet for Assembly Repair vs. Replacement. Technician will use the latest version of 09-06-04-026G to verify the Engine Control Module calibration is not an aftermarket calibration. If the customer prefers to keep the original numbers matching engine please call General Motors Technical Assistance Center for repair direction. |
| PIP5179A | 2017-08-15. Service bulletin. FUEL SYSTEM, GASOLINE:FUEL INJECTION SYSTEM; ENGINE. This Preliminary Information communication provides information to the technician about vehicles that have extended or long crank time during cold ambient air temperatures. Direct Injection systems run at higher pressures, and the mechanical pump on the engine must build up the required pressure before the first injection event occurs. Direct Injection engines may have slightly longer cold crank times than that of port fuel engines. |
| PIP5272A | 2017-08-15. Service bulletin. ENGINE. This Preliminary Information communication provides information to the technician about vehicles that may have low oil pressure after an oil change. Technician will inspect the oil filter part number PF63E. Part number PF48 oil filter will fit but will cause a low oil pressure concern. |
| PIT5448 | 2017-08-15. Service bulletin. ENGINE. This Preliminary Information communication provides information to the technician about vehicles that stop running after it has been idling for 2.5 hours. This is normal operation of the vehicle built with regular production code BTM. |
| PIT5447 | 2017-08-15. Service bulletin. ENGINE AND ENGINE COOLING:EXHAUST SYSTEM:MANIFOLD/HEADER/MUFFLER/TAIL PIPE. This Preliminary Information communication provides information to the technician on the steps needed to diagnose and repair vehicles that may have a rattle noise from the dash. Technician will need to inspect for the rear heater pipes contacting the passenger side exhaust manifold. If the rear heater pipe is found to be contacting the exhaust manifold, reposition the heater pipe so it no longer makes contact. |
| PIP5211C | 2017-08-15. Service bulletin. ENGINE; SUSPENSION. This Preliminary Information communication provides information to the technician the steps needed to diagnose and repair vehicles with a rough idle and/or vibration at idle in Drive. This condition will not be present in Park, or Neutral. This concern may be caused by ground out within the one or both engine mounts. Technician will use CH-51450-A (Pico Oscilloscope) to measure the vibration disturbance. If the vibration concern is E1.5 in the horizontal / lateral direction with Pico sensor mounted in seat track as indicated ? continue with steps to reduce the amplitude of the vibration by adding spacers in key locations to reduce ground out within the engine mounts. The 6.2L engine has a characteristic E1 which can be felt, and may be described as a lopey idle. Do not confuse 6.2L E1 characteristic (not caused by mount ground-out), with E1.5 normal idle characteristics being transmitted into the truck via ground-out thru the engine mounts. If measuring high at the seat track 12 mg or greater; replacement of the engine mounts should help reduce the amplitude of the vibration. If the disturbance measures at the seat track as E 1.5 lateral in the range of approximately 2.5 - 8 mg using a tri-axis sensor. Then place tri-axis Pico sensor on the inboard seat track forward-most location to record measurement of the rough idle vibration concern. With the Heater-Vent-Air Conditioning on perform several short heavy launch events from stop to stop to bring the temperatures back up while attempting to re-create the rough idle vibration in Drive with Pico sensor placed on inboard seat track; while the vibration is active ? Record Pico reading. This method seems to provide better results than extended test drives. If the Pico reading for E1.5, with vibration active, at specified seat track location measures close to 2mg or less use Service Information to diagnose rough idle / vibration. If the Pico reading for E1.5, with vibration active, at the inboard forward seat track |
| PIT5245B | 2017-08-15. Service bulletin. ENGINE AND ENGINE COOLING. This Preliminary Information communication provides information to the technician about vehicles that the blower motor may be noisy or vibrate when running. This concern will only occur when the temperatures is below 32 degrees Fahrenheit and if the blower motor is removed while still cold, ice may be found on the blower motor cage. This concern could be caused by water leaking or snow ingestion into the Heater-Vent-Air Conditioning case. Technician is to perform normal water testing diagnostics while the Heater-Vent-Air Conditioning is running, looking for water leaking past the plenum cover. If water is leaking past the cover remove the cover and install a 12x12 snow resistant screen to the fresh air intake. Reseal and install the plenum cover cap using Kent air dry sealer or equivalent. |
| PIP5288 | 2017-08-15. Service bulletin. ENGINE. This Preliminary Information communication advises the technician to check for an engine build code of K and the dates between 15005 and 15117, the customer concern is an engine oil leak at the oil filter location of the oil pan. A loose oil filter adapter is found to be the cause of the concern, tighten it to 55 newton meters or 40 foot pounds. It is also advised to clean any residual oil from the oil pan area. |
| PIP5282 | 2017-08-15. Service bulletin. ENGINE AND ENGINE COOLING. This Preliminary Information communication advises the technician about the calculation and operation of the engine oil life monitor. The monitor calculates the percent of oil life remaining, based on 3 pathways. The first pathway for oil life calculation is engine revolutions. The second pathway for oil life calculation is the mileage form the last rest for all General Motors powertrains except the Volt. The third pathway for oil life calculation is the amount of time the oil is in the engine. The Volt uses a 2 year timer instead of 1 year. It also uses the engine revolution counter. It does not use the mileage pathway to count down. |
| 09-06-04-026M | 2017-08-15. Service bulletin. ELECTRICAL SYSTEM:SOFTWARE; ENGINE. This informational bulletin provides information on identifying non-GM (aftermarket) engine calibrations for gasoline engines using Tech 2 or GDS 2. |
| PIT5308B | 2017-08-15. Service bulletin. STRUCTURE:BODY:HATCHBACK/LIFTGATE; ELECTRICAL SYSTEM; ENGINE. This Preliminary Information communication provides information to the technician on the steps to diagnose and repair vehicles that have remote start is inoperative, power lift gate Regular Production Option Code (TB5) is inoperative with the ignition off, Crank no start, Start and Stall, and vehicles equipped with the diesel engine, the blower motor may stay on after the engine is turned off. Technician may find Diagnostic Trouble Code P2537 and/or P129Dset. Technician will need to Use a voltmeter and check circuit 5985 at the Engine Control Module and Transmission Control Module. If no or low voltage is found, use the wiring diagram in Service Information and perform normal circuit diagnosis. |
The summaries are NHTSA's. Each bulletin's page links NHTSA's copy of the manufacturer's document.