Service bulletins for the 2013 GMC Yukon
A bulletin is a manufacturer's communication to its dealers, as NHTSA indexes it. The summary is NHTSA's. The document is the manufacturer's: read it at NHTSA. A bulletin is not a recall, and listing a model year does not mean every vehicle of it is concerned.
1840 on file from NHTSA, as of 2026-10-19.
By type
By component
By trouble code
By topic
Only bulletins with component: Engine are shown. Show all
| 07-06-04-019E | 2017-08-15. Service bulletin. ELECTRICAL SYSTEM; ENGINE AND ENGINE COOLING. This technical bulletin provides repair information for repairing the IP to body harness connector to correct a customer concern for intermittent Malfunction Indicator Lamp (MIL) illuminated with Reduced Engine Power displayed and DTC P2138 set. |
|---|---|
| 15-00-89-004A | 2017-08-15. Service bulletin. ENGINE AND ENGINE COOLING. This informational bulletin provides technicians with updated information to help identify the differences between what is considered a fluid leak, and what is considered seepage. |
| 00-06-01-026F | 2017-08-15. Service bulletin. ENGINE AND ENGINE COOLING. This informational bulletin provides information to technicians regarding intake manifold inspection/replacement after severe internal engine damage. |
| 06-00-89-026L | 2017-08-15. Service bulletin. SERVICE BRAKES; EQUIPMENT:ELECTRICAL; ENGINE AND ENGINE COOLING:EXHAUST SYSTEM; EQUIPMENT:APPLIANCE:AIR CONDITIONER; POWER TRAIN:AXLE ASSEMBLY; EQUIPMENT ADAPTIVE/MOBILITY; ELECTRICAL SYSTEM. This warranty administration bulletin provide policy information on a revised customer concern not duplicated/verified labor operation numbers and how to submit CCND. |
| 06-06-01-010B | 2017-08-15. Service bulletin. EQUIPMENT:MECHANICAL; ENGINE AND ENGINE COOLING. This informational bulletin provides information on close-coupled converter and engine replacement. |
| PI0434B | 2017-08-15. Service bulletin. ENGINE AND ENGINE COOLING:EXHAUST SYSTEM. This preliminary information bulletin provides a procedure for the dampener, exhaust install or replacement to eliminate a drone, vibration or rattle type noise coming from the exhaust system with engine RPMs at 1700. |
| PIP5029H | 2017-08-15. Service bulletin. ENGINE. This Preliminary Information communication provides information to the technician about vehicles that have a Malfunction Indicator Lamp on or engine misfire, rough idle, extended crank, or crank no start in some cases. Technician will need to perform published Service Information diagnostics. If technician finds carbon, an upper engine and valve cleaning should be performed. Update added part numbers for the cleaner and model years. |
| PIP3119N | 2017-08-15. Service bulletin. ENGINE; ENGINE AND ENGINE COOLING:EXHAUST SYSTEM:EMISSION CONTROL:CATALYTIC CONVERTOR; POWER TRAIN. This Preliminary Information communication provides information to the technician on the steps to diagnose and repair vehicles that may have a Service Engine Soon Malfunction Indicator Lamp on at low mileage. Technician may find Diagnostic Trouble Codes P0420 and or P0430 stored. Technician should be advised that the catalytic converter efficiency Diagnostic Trouble Codes P0420 and P0430 are disabled for the first hour of engine run time to allow break-in of the catalytic converter. Technician will need to use a Tech2 to check the verify engine run time on the Engine Hour Meter in the Instrument Panel Cluster Data Display/Data 1 List in the scan tool match. If the engine run time is less than one hour, the battery may have been disconnected, or another vehicle power loss event may have occurred, during vehicle manufacturing. Technician will need to clear the Diagnostic Trouble Codes and perform a drive cycle. If the catalytic converter was replaced and the Diagnostic Trouble Codes set it may be a result of the engine run time restrictions no longer being in place since the vehicle is no longer new. Technician will need to clear the Diagnostic Trouble Codes and perform a drive cycle. |
| PIP5148 | 2017-08-15. Service bulletin. EQUIPMENT; ENGINE. This Preliminary Information communication provides information to the technician about vehicles that a tick ping noise on torque reversal or load. Technician will need to replace the propeller shaft. Technician will need to contact General Motors Technical Assistance Center for further assistance if the vehicle was built January 1, 2013 or later. |
| PIP4568N | 2017-08-15. Service bulletin. ENGINE AND ENGINE COOLING. This Preliminary Information communication provides information to the technician that some vehicles may have a Service Engine Soon lamp, engine misfire on cylinder 1, 4, 6, or 7 and/or tick noise. Technician will follow service information diagnosis first. If service information diagnosis does not isolate the cause of this concern perform a cylinder deactivation active fuel management system compression test in service information. If the running compression of the misfiring cylinder stays below 25 Pounds per Square Inch regardless of the active fuel management solenoid being commanded on or off, an active fuel management lifter is mechanically collapsed/stuck or unlocking as soon as the engine is started. Replace all active fuel management lifters, and all plastic lifter guides. Also perform the cylinder deactivation active fuel management Valve Lifter Oil Manifold Diagnosis and Testing in Service Information. If it isolates a concern with the Valve Lifter Oil Manifold, replace it and reevaluate the concern. The active fuel management lifters can also be monitored for proper operation by carefully inspecting the cylinder 1, 4, 6, and 7 rockers and valves while cranking or briefly and safely running the engine with the valve covers removed. If the valve or valves of an active fuel management cylinder stop moving while doing this test, the active fuel management lifter is causing the concern. For 2008-2009 Full Size Truck/SUV or a 2007-2009 Chevrolet Tahoe with the Police Package reprogram the Engine Control Module. On the 2008-2009 Pontiac G8, 2010-2011 Camaro, and 2007-2010 Full Size Trucks with active fuel management, also determine if the active fuel management pressure relief valve shield that is listed in the latest version of 10-06-01-008 has ever been installed. On passenger cars with the LS4 engine, determine if the updated oil pan gasket that is listed in the latest version of 11-06-01-007 has been installed. |
| PIP4138N | 2017-08-15. Service bulletin. ENGINE; ELECTRICAL SYSTEM. This Preliminary Information communication provides information to the technician about vehicles that have a Service Engine Soon Malfunction Indicator Lamp on, engine misfire, and/or engine noise. Technician may find Diagnostic Trouble Codes P0300-P0308. If published Service Information diagnostics does not isolate the cause of this concern technician should check for a worn camshaft lobe and/or lifter roller, a sticking valve, valve leakage, a broken valve spring, and a collapsed active fuel management lifter. |
| PIP4568M | 2017-08-15. Service bulletin. ENGINE AND ENGINE COOLING. This Preliminary Information communication provides information to the technician that some vehicles may have a Service Engine Soon lamp, engine misfire on cylinder 1, 4, 6, or 7 and/or tick noise. Technician will follow service information diagnosis first. If service information diagnosis does not isolate the cause of this concern perform a cylinder deactivation active fuel management system compression test in service information. If the running compression of the misfiring cylinder stays below 25 Pounds per Square Inch regardless of the active fuel management solenoid being commanded on or off, an active fuel management lifter is mechanically collapsed/stuck or unlocking as soon as the engine is started. Replace all active fuel management lifters, and all plastic lifter guides. Also perform the cylinder deactivation active fuel management Valve Lifter Oil Manifold Diagnosis and Testing in Service Information. If it isolates a concern with the Valve Lifter Oil Manifold, replace it and reevaluate the concern. The active fuel management lifters can also be monitored for proper operation by carefully inspecting the cylinder 1, 4, 6, and 7 rockers and valves while cranking or briefly and safely running the engine with the valve covers removed. If the valve or valves of an active fuel management cylinder stop moving while doing this test, the active fuel management lifter is causing the concern. For 2008-2009 Full Size Truck/SUV or a 2007-2009 Chevrolet Tahoe with the Police Package reprogram the Engine Control Module. On the 2008-2009 Pontiac G8, 2010-2011 Camaro, and 2007-2010 Full Size Trucks with active fuel management, also determine if the active fuel management pressure relief valve shield that is listed in the latest version of 10-06-01-008 has ever been installed. On passenger cars with the LS4 engine, determine if the updated oil pan gasket that is listed in the latest version of 11-06-01-007 has been installed. |
| PIP4158F | 2017-08-15. Service bulletin. ENGINE. This Preliminary Information communication provides information to the technician about vehicles that have low oil pressure, no oil pressure, and/or engine noise. Technician will need to replace the oil pump, flush the oil cooler lines. |
| PIP5108A | 2017-08-15. Service bulletin. ENGINE AND ENGINE COOLING. This Preliminary Information communication provides information to the technician about vehicles that have an audible engine whine noise at 1500-1800 revolutions per minute. Technician will need to check the coolant level, remove serpentine belt to verify noise goes away, rotate the thermostat 90 degrees and retest, then replace thermostat and retest. Technician will replace the water pump if there is no change. |
| PIP3119L | 2017-08-15. Service bulletin. ENGINE AND ENGINE COOLING; ENGINE AND ENGINE COOLING:EXHAUST SYSTEM; ENGINE AND ENGINE COOLING:EXHAUST SYSTEM:EMISSION CONTROL:CATALYTIC CONVERTOR. This Preliminary Information communication provides information to the technician on the steps to diagnose and repair vehicles that may have a Service Engine Soon Malfunction Indicator Lamp on at low mileage. Technician may find Diagnostic Trouble Codes P0420 and or P0430 stored. Technician should be advised that the catalytic converter efficiency Diagnostic Trouble Codes P0420 and P0430 are disabled for the first hour of engine run time to allow break-in of the catalytic converter. Technician will need to use a Tech2 to check the verify engine run time on the Engine Hour Meter in the Instrument Panel Cluster Data Display/Data 1 List in the scan tool match. If the engine run time is less than one hour, the battery may have been disconnected, or another vehicle power loss event may have occurred, during vehicle manufacturing. Technician will need to clear the Diagnostic Trouble Codes and perform a drive cycle. If the catalytic converter was replaced and the Diagnostic Trouble Codes set it may be a result of the engine run time restrictions no longer being in place since the vehicle is no longer new. Technician will need to clear the Diagnostic Trouble Codes and perform a drive cycle. |
| PIP4158G | 2017-08-15. Service bulletin. ENGINE. This Preliminary Information communication provides information to the technician about vehicles that have low oil pressure, no oil pressure, and/or engine noise. Technician will need to replace the oil pump, flush the oil cooler lines. |
| PIP5108 | 2017-08-15. Service bulletin. ENGINE AND ENGINE COOLING; ENGINE AND ENGINE COOLING:COOLING SYSTEM. This Preliminary Information communication provides information to the technician about vehicles that have an audible engine whine noise at 1500-1800 revolutions per minute. Technician will need to check the coolant level, remove serpentine belt to verify noise goes away, rotate the thermostat 90 degrees and retest, then replace thermostat and retest. Technician will replace the water pump if replacing the thermostat does not repair the audible engine whine noise. |
| PIP4158E | 2017-08-15. Service bulletin. ENGINE AND ENGINE COOLING:COOLING SYSTEM; ENGINE AND ENGINE COOLING. This Preliminary Information communication provides information to the technician about vehicles that have low oil pressure, no oil pressure, and/or engine noise. Technician will need to replace the oil pump, flush the oil cooler lines. |
| PIP5003C | 2017-08-15. Service bulletin. ENGINE AND ENGINE COOLING. This Preliminary Information communication provides information to the technician about vehicles that have a service four wheel drive message displayed in the driver?s information center. Technician may find Diagnostic Trouble Code C0387. Technician should follow published Service Information diagnostics for the Diagnostic Trouble Code if it is a current code. Technician will need to attempt to duplicate the concern if the Diagnostic Trouble Code is set history. If the customer experiences repeat occurrences of this condition and a root cause cannot be determined, it is probable that the transfer case encoder motor is not responding quickly enough and should be replaced. |
| PIP4819A | 2017-08-15. Service bulletin. ENGINE; EXTERIOR LIGHTING; ELECTRICAL SYSTEM. This Preliminary Information communication provides information to the technician about vehicles that have Service Engine Soon Malfunction Indicator Lamp and the engine misfires. Technician may find Diagnostic Trouble Codes P0300, P0301, P0302, P0303, P0304, P0305, P0306, P0307, and P0308. Technician will need to inspect the spark plug wires. Technician will need to replace any loose spark plug wires. |
| PIP3119K | 2017-08-15. Service bulletin. ENGINE; ENGINE AND ENGINE COOLING:EXHAUST SYSTEM:EMISSION CONTROL:CATALYTIC CONVERTOR. This Preliminary Information communication provides information to the technician on the steps to diagnose and repair vehicles that may have a Service Engine Soon Malfunction Indicator Lamp on at low mileage. Technician may find Diagnostic Trouble Codes P0420 and or P0430 stored. Technician should be advised that the catalytic converter efficiency Diagnostic Trouble Codes P0420 and P0430 are disabled for the first hour of engine run time to allow break-in of the catalytic converter. Technician will need to use a Tech2 to check the verify engine run time on the Engine Hour Meter in the Instrument Panel Cluster Data Display/Data 1 List in the scan tool match. If the engine run time is less than one hour, the battery may have been disconnected, or another vehicle power loss event may have occurred, during vehicle manufacturing. Technician will need to clear the Diagnostic Trouble Codes and perform a drive cycle. If the catalytic converter was replaced and the Diagnostic Trouble Codes set it may be a result of the engine run time restrictions no longer being in place since the vehicle is no longer new. Technician will need to clear the Diagnostic Trouble Codes and perform a drive cycle. |
| PIP5089 | 2017-08-15. Service bulletin. ELECTRICAL SYSTEM; ENGINE AND ENGINE COOLING. This Preliminary Information communication provides information to the technician about vehicles that have a Diagnostic Trouble Code C0569 that will not clear. Technician should be advised if there are any issues with the rotational position sensor, incremental position sensor, encoder motor, motor A or B circuits, rotational position sensor or incremental position sensor circuits when the transfer case control module attempts to determine location the location cannot be determined correctly. |
| 09-06-04-026L | 2017-08-15. Service bulletin. ENGINE. This informational bulletin provides information on Identifying Non-GM (Aftermarket) Engine Calibrations for Gasoline Engines Using Tech 2® or GDS 2 (U.S. and Canada) |
| PIP5083 | 2017-08-15. Service bulletin. ENGINE. This Preliminary Information communication provides information to the technician about vehicles that have misfires on cylinders 1, 4, 6 and 7. Technician should inspect the camshaft part numbers. Technician should ensure to use part number for the application by using the numbers stamped on the cam. |
| PIP4138M | 2017-08-15. Service bulletin. ENGINE. This Preliminary Information communication provides information to the technician about vehicles that have a Service Engine Soon Malfunction Indicator Lamp on, engine misfire, and/or engine noise. Technician may find Diagnostic Trouble Codes P0300-P0308. If published Service Information diagnostics does not isolate the cause of this concern technician should check for a worn camshaft lobe and/or lifter roller, a sticking valve, valve leakage, a broken valve spring, and a collapsed active fuel management lifter. |
The summaries are NHTSA's. Each bulletin's page links NHTSA's copy of the manufacturer's document.