WenmarOpen by Wenmar Pro

Service bulletins for the 2011 GMC Yukon

A bulletin is a manufacturer's communication to its dealers, as NHTSA indexes it. The summary is NHTSA's. The document is the manufacturer's: read it at NHTSA. A bulletin is not a recall, and listing a model year does not mean every vehicle of it is concerned.

1700 on file from NHTSA, as of 2026-10-19.

By type

By component

By trouble code

By topic

Only bulletins with component: Backup camera are shown. Show all

Bulletins, newest first
15NA082B2024-02-12. Service bulletin. BACK OVER PREVENTION. Clunking Noise from Front of Vehicle During Turns and/or Bumps
15NA0822024-02-12. Service bulletin. BACK OVER PREVENTION. Clunking Noise from Front of Vehicle During Turns and/or Bumps
PIT4684A2023-12-26. Service bulletin. BACK OVER PREVENTION. Rear Camera Display Blank.
120232002A2023-12-04. Service bulletin. POWER TRAIN; BACK OVER PREVENTION; STEERING:HYDRAULIC POWER ASSIST:POWER STEERING FLUID; STEERING; STEERING:HYDRAULIC POWER ASSIST:HOSE, PIPING, AND CONNECTIONS; STEERING:HYDRAULIC POWER ASSIST:PUMP; SERVICE BRAKES. Power Steering Noise or Fluid Leak from Power Steering Pump, Gear or High Pressure Pressure Hose During Extreme Low Temperature Operation (Replace Power Steering Fluid)
PIT4684A2023-11-20. Service bulletin. BACK OVER PREVENTION. Rear Camera Display Blank.
070601016G2022-06-13. Service bulletin. BACK OVER PREVENTION. This informational bulletin provides information on Internal Engine Noise or Damage After Oil Filter Replacement.
PI0608A2018-04-23. Service bulletin. BACK OVER PREVENTION: SENSING SYSTEM: CAMERA. This preliminary information bulletin provides information and additional diagnostics on park assist blocked being messaged on the DIC.
PI0534A2018-04-16. Service bulletin. BACK OVER PREVENTION; VEHICLE SPEED CONTROL. This preliminary informational bulletin provides information on dignostics for a whine noise at varies engine speeds.
10-00-89-006C2018-04-16. Service bulletin. BACK OVER PREVENTION: SENSING SYSTEM: RADAR. This informational bulletin provides directions on submitting different PIRs
PIP5168F2018-02-21. Service bulletin. POWER TRAIN:AXLE ASSEMBLY:AXLE SHAFT; BACK OVER PREVENTION; FUEL SYSTEM, GASOLINE. This Preliminary Information communication provides information to the technician on the steps to diagnose and repair vehicles that may have a no crank concern. Technician will need to check the valve train for movement when the engine is cranked. If the valve train is not moving while the crankshaft is moving the front cover will need to be removed to inspect for a sheared cam sprocket locator pin. If the cam sprocket locator pin has sheared, replace the engine assembly. If the valve train is rotating during inspection, disconnect the Camshaft Position sensor and check if the engine will start. If the engine starts front cover will need to be removed to inspect for a sheared cam sprocket locator pin. If the cam sprocket locator pin has sheared, replace the engine assembly. If the engine does not start with the Camshaft Position sensor disconnected the follow published “Engine Cranks But Does Not Run” diagnosis in Service Information. Also perform an Engine Compression Test and Cylinder Leakage Test in Service Information documents all results. If the Service Information procedures above isolate an engine mechanical concern then removed to inspect for a sheared cam sprocket locator pin. If the cam sprocket locator pin has sheared, replace the engine assembly.
PIT5209A2017-12-22. Service bulletin. ELECTRICAL SYSTEM; BACK OVER PREVENTION: BACK-UP ALARM; BACK OVER PREVENTION; STRUCTURE. This Preliminary Information communication provides information to the technician about vehicles that for no reason the alarm will go active. Technician will need to use a scan tool to verify that the alarm was activated by the inclination sensor. If the trigger is the inclination sensor, inspect the sensor's mounting location. Technician will need to relocate the sensor if it is attached to the driver's side lower Heater-Vent-Air Conditioning duct. Technician will need to reinstall the sensor to the top of the Body Control Module bracket.
PIT4684B2017-08-15. Service bulletin. BACK OVER PREVENTION: CAMERA SYSTEM; ELECTRICAL SYSTEM:WIRING. This Preliminary Information communication provides information to the technician about vehicles that have a rear camera display being inoperative when shifting into reverse. Technician should check for a loose or disconnected X421/X322 connector behind the right side "C" pillar trim. Technician should also check for pinched, Open or shorted wires on camera circuits 7641, 7642, and 6799.

The summaries are NHTSA's. Each bulletin's page links NHTSA's copy of the manufacturer's document.