WenmarOpen by Wenmar Pro

Service bulletins for the 2010 GMC Yukon XL

A bulletin is a manufacturer's communication to its dealers, as NHTSA indexes it. The summary is NHTSA's. The document is the manufacturer's: read it at NHTSA. A bulletin is not a recall, and listing a model year does not mean every vehicle of it is concerned.

1420 on file from NHTSA, as of 2026-10-19.

By type

By component

By trouble code

By topic

Only bulletins with component: Transmission and driveline are shown. Show all

Bulletins, newest first
PI09382018-04-23. Service bulletin. ELECTRICAL SYSTEM; POWER TRAIN. This preliminary information bulletin provides information on powertrain and various electronic/electrical control issues.
13-08-116-001A2018-04-23. Service bulletin. TIRES:PRESSURE MONITORING AND REGULATING SYSTEMS; POWER TRAIN; ELECTRICAL SYSTEM; EQUIPMENT:ELECTRICAL:RADIO/TAPE DECK/CD ETC.. This technical bulletin provides a procedure on aftermarket ALSL or DLC devices causing multiple issues due to suspected tampering.
09-06-04-026G2018-04-23. Service bulletin. ENGINE; POWER TRAIN. This informational bulletin provides information of suspected tampering or vehicle modifications for non-GM (Aftermarket) engine and transmission calibrations for V6 and V8 gasoline engines Using Tech 2® or global diagnostic system 2 (GDS 2)
PI0522D2018-04-23. Service bulletin. POWER TRAIN:AUTOMATIC TRANSMISSION. This preliminary information bulletin provides a procedure to adjust the transmission dipstick tube and/or install the transmission fluid filler tube sleeve to eliminate a tick, buzz or rattle noise from the front of dash, transmission filler tuber cracked or broken.
12-07-30-001B2018-04-16. Service bulletin. POWER TRAIN. This informational bulletin provides information for service agents not required to contact product quality center for CNG, LPG or gasoline engine, transmission and/or transfer case.
06-00-89-031C2017-12-22. Service bulletin. POWER TRAIN; EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL. This informational bulletin provides information to dealership personnel on proper engine and automatic transmission/transaxle identification.
030729004I2017-12-22. Service bulletin. POWER TRAIN. This informational bulletin was created for the Manual Transmission Operating Characteristics. The different noises caused by driver habit, weather conditions , and normal manual transmission noises.
1203100022017-12-22. Service bulletin. POWER TRAIN:AUTOMATIC TRANSMISSION:TORQUE CONVERTER. This informational bulletin provides a description of the proper wheel installation and proper wheel torque techniques used to install wheels onto vehicles
PIP4112P2017-12-22. Service bulletin. ENGINE; POWER TRAIN. This Preliminary Information communication provides information to the technician of a complaint of a sag or hesitation when accelerating. The concern is present when coasting at low speeds of less than 15 miles per hour and then aggressively applying the throttle, or after making a hard stop followed by an aggressive throttle. This is considered normal operation of the vehicle the throttle is delayed and opened slowly up to .7 seconds to help minimize driveline lash and clunking or will have approximately .5 seconds of zero torque to allow the transmission to shift to first gear.
PIP4653E2017-12-22. Service bulletin. POWER TRAIN:AUTOMATIC TRANSMISSION:CONTROL MODULE (TCM/PCM/TECM); POWER TRAIN. This Preliminary Information communication provides information to the technician about vehicle that have a Malfunction Indicator Lamp on. Technician may find Diagnostic Trouble Codes P0601, P0603, P0604, P062F or P1621 stored in the Transmission Control Module. Technician will need to ensure that the Diagnostic Trouble Codes are set in the Transmission Control Module. If the Diagnostic Trouble Codes are only set in the Transmission Control Module reprogram the Transmission Control Module.
09-07-30-018C2017-10-12. Service bulletin. POWER TRAIN; POWER TRAIN:AUTOMATIC TRANSMISSION. This warranty administration bulletin provides information on the change in automatic transmission add conditions documentation and claim submissions
PIT54422017-08-15. Service bulletin. POWER TRAIN; EQUIPMENT:ELECTRICAL. This Preliminary Information communication provides information to the technician of an engine power reduced message on the driver information center after performing the Canada Onstar® 4G upgrade. If the concern is present park the vehicle outside and call General Motors Technical Assistance Center.
PI1344A2017-08-15. Service bulletin. POWER TRAIN:CLUTCH ASSEMBLY. This preliminary bulletin provides a procedure to remove and inspect the clutch select solenoid valve for damage, located in the valve body to correct the customers concern of reduced acceleration at low speeds and trans slip at lauch.
PIT4575D2017-08-15. Service bulletin. POWER TRAIN; ENGINE. This Preliminary Information communication advises the technician vehicles with Regular Production Option Code HP2 may stall after shifting out of park quickly after a key crank. The 2-Mode Hybrid requires a certain amount of engine run time (1-2 seconds) from initial key crank before moving the gear shift indicator out of park. This is a normal condition and no parts should be replaced to try and resolve this concern.
PI08762017-08-15. Service bulletin. POWER TRAIN:AUTOMATIC TRANSMISSION. This preliminary informational bulletin provides information on replacing the transmission fluid level indicator if a customers comments regarding one being broken.
02-07-30-052J2017-08-15. Service bulletin. POWER TRAIN:AUTOMATIC TRANSMISSION; POWER TRAIN:AUTOMATIC TRANSMISSION:COOLING UNIT AND LINES. This informational bulletin provides technicians with information regarding automatic transmission oil cooler flow test essential tool J-45096 TransFlow®.
06-00-89-026L2017-08-15. Service bulletin. SERVICE BRAKES; EQUIPMENT:ELECTRICAL; ENGINE AND ENGINE COOLING:EXHAUST SYSTEM; EQUIPMENT:APPLIANCE:AIR CONDITIONER; POWER TRAIN:AXLE ASSEMBLY; EQUIPMENT ADAPTIVE/MOBILITY; ELECTRICAL SYSTEM. This warranty administration bulletin provide policy information on a revised customer concern not duplicated/verified labor operation numbers and how to submit CCND.
PIP3119N2017-08-15. Service bulletin. ENGINE; ENGINE AND ENGINE COOLING:EXHAUST SYSTEM:EMISSION CONTROL:CATALYTIC CONVERTOR; POWER TRAIN. This Preliminary Information communication provides information to the technician on the steps to diagnose and repair vehicles that may have a Service Engine Soon Malfunction Indicator Lamp on at low mileage. Technician may find Diagnostic Trouble Codes P0420 and or P0430 stored. Technician should be advised that the catalytic converter efficiency Diagnostic Trouble Codes P0420 and P0430 are disabled for the first hour of engine run time to allow break-in of the catalytic converter. Technician will need to use a Tech2 to check the verify engine run time on the Engine Hour Meter in the Instrument Panel Cluster Data Display/Data 1 List in the scan tool match. If the engine run time is less than one hour, the battery may have been disconnected, or another vehicle power loss event may have occurred, during vehicle manufacturing. Technician will need to clear the Diagnostic Trouble Codes and perform a drive cycle. If the catalytic converter was replaced and the Diagnostic Trouble Codes set it may be a result of the engine run time restrictions no longer being in place since the vehicle is no longer new. Technician will need to clear the Diagnostic Trouble Codes and perform a drive cycle.
PIP4112M2017-08-15. Service bulletin. POWER TRAIN:AUTOMATIC TRANSMISSION. This Preliminary Information communication provides information to the technician of a complaint of a sag or hesitation when accelerating. The concern is present when coasting at low speeds of less than 15 miles per hour and then aggressively applying the throttle, or after making a hard stop followed by an aggressive throttle. This is considered normal operation of the vehicle the throttle is delayed and opened slowly up to .7 seconds to help minimize driveline lash and clunking or will have approximately .5 seconds of zero torque to allow the transmission to shift to first gear.
PIP4112L2017-08-15. Service bulletin. POWER TRAIN:AUTOMATIC TRANSMISSION. This Preliminary Information communication provides information to the technician of a complaint of a sag or hesitation when accelerating. The concern is present when coasting at low speeds of less than 15 miles per hour and then aggressively applying the throttle, or after making a hard stop followed by an aggressive throttle. This is considered normal operation of the vehicle the throttle is delayed and opened slowly up to .7 seconds to help minimize driveline lash and clunking or will have approximately .5 seconds of zero torque to allow the transmission to shift to first gear.
PIP50872017-08-15. Service bulletin. POWER TRAIN:AXLE ASSEMBLY. This Preliminary Information communication provides information to the technician about vehicles that may have a service 4WD message displayed in the Driver Information Center. Technician may find Diagnostic Trouble Code C0379. Technician will need to inspect the front axle actuator connector for signs of moisture intrusion. If there is corrosion on the terminals at either location replace the actuator and harness.
PIP4138L2017-08-15. Service bulletin. EQUIPMENT:MECHANICAL; POWER TRAIN. This Preliminary Information communication provides information to the technician about vehicles that have a Service Engine Soon Malfunction Indicator Lamp on, engine misfire, and/or engine noise. Technician may find Diagnostic Trouble Codes P0300-P0308. If published Service Information diagnostics does not isolate the cause of this concern technician should check for a worn camshaft lobe and/or lifter roller, a sticking valve, valve leakage, a broken valve spring, and a collapsed active fuel management lifter.
PIP4600C2017-08-15. Service bulletin. POWER TRAIN:AUTOMATIC TRANSMISSION. This Preliminary Information communication advises the technician that 2ML70 Transmission Assembly will be placed on a parts restriction through the General Motors Technical Assistance Center. Dealer will need to contact General Motors Technical Assistance Center for further assistance.
PIT4505F2017-08-15. Service bulletin. POWER TRAIN:AUTOMATIC TRANSMISSION. This Preliminary Information communication provides information to the technician about vehicles that have a rattle, buzz, tick, or vibration type noise that appears to be coming from the center of the dash. Technician will adjust the transmission dipstick tube away from the front of cowl to provide additional clearance.
PIP3720D2017-08-15. Service bulletin. POWER TRAIN:AXLE ASSEMBLY. This Preliminary Information communication provides information to the technician with the axel setup information from American Axle Manufacturing. Technician should be advised that the maximum pinion shim to be used or stacked behind the pinion is 0.050?, and the minimum pinion shim is 0.020? for an 8.6 axle. The range for available pinion depth shims for the 10.5? axle is 0.006? to 0.024?. When setting the backlash it should be set between 0.003? to 0.005? on a new ring and pinion for any American Axle Manufacturing application. The ring and pinion can be reused or adjusted if the mileage is less than 500 miles, if not used for towing. Technician should be advised that a ?roller coaster? or ?hourglass? pattern on the bearings may be normal up to 10,000 miles and possibly longer. With a mis-machined housing you may get a heel pattern on both sides of the gear teeth at build up can generally be corrected with backlash adjustments. When setting up an 8.6? axle with a 5 cut gear set is to use a 0.035? pinion shim and set backlash to 0.004?. When using the newer 2 cut gear set also use a 0.035? pinion shim and still set backlash to 0.004?. To set the gear pattern use backlash to adjust the pattern heel to toe. Use the pinion shim to adjust the height of the pattern. The proper drive pinion bearing pre-load is from 15 - 30 inch pounds with new bearings. The total torque to turn after the differential case is installed should increase 5 - 10 inch pounds at the pinion. A new pinion nut must be used whenever the old one is removed. The axle shaft end play specification is 0.012? per side and the radial specification is 0.002? - 0.003?. Technician should be advised that synthetic lube can be used in all new American Axle Manufacturing axle assemblies. The new pinion seal for the 8.6? axle assembly is a two piece design.

The summaries are NHTSA's. Each bulletin's page links NHTSA's copy of the manufacturer's document.