Service bulletins for the 2007 GMC Yukon XL
A bulletin is a manufacturer's communication to its dealers, as NHTSA indexes it. The summary is NHTSA's. The document is the manufacturer's: read it at NHTSA. A bulletin is not a recall, and listing a model year does not mean every vehicle of it is concerned.
1084 on file from NHTSA, as of 2026-10-19.
By type
By component
By trouble code
By topic
| PIT4261C | 2017-08-15. Service bulletin. TIRES:SIDEWALL. This Preliminary Information communication provides information to the technician about vehicles with tire sidewall irregularities. This is a visual condition that will not affect durability, reliability or performance of the tires. Dealer should communicate to the customer that slight sidewall indentations are a common characteristic of radial tire construction. |
|---|---|
| PIC4801E | 2017-08-15. Service bulletin. EQUIPMENT:ELECTRICAL:NAVIGATIONAL SYSTEM(GLOBAL POSITIONING SYSTEM); EQUIPMENT:ELECTRICAL. This Preliminary Information communication provides information to the technician on how to diagnose and repair vehicles that may have an OnStar Turn-By-Turn Navigation the system that is inoperative. Technician verifies there are no Diagnostic Trouble Codes are present in the Antilock Braking System and Vehicle Communication Interface Module of the vehicle. If no Diagnostic Trouble Codes found call OnStar using the Blue button on the OnStar key pad and ask the advisor for a turn by turn route. Also make a OnStar personal call and a call into the vehicle. If normal diagnostics do not lead to a resolution technician will need to call General Motors Technical Assistance Center for further assistance. |
| PIC4310H | 2017-08-15. Service bulletin. EQUIPMENT:ELECTRICAL:NAVIGATIONAL SYSTEM(GLOBAL POSITIONING SYSTEM); EQUIPMENT:ELECTRICAL. This Preliminary Information communication provides information to the technician about vehicle that may have an OnStar system that has progression tones when pressing the blue or red button. Technician will need to call General Motors Technical Assistance Center with the scan tool data from the OnStar system. |
| PIT4505F | 2017-08-15. Service bulletin. POWER TRAIN:AUTOMATIC TRANSMISSION. This Preliminary Information communication provides information to the technician about vehicles that have a rattle, buzz, tick, or vibration type noise that appears to be coming from the center of the dash. Technician will adjust the transmission dipstick tube away from the front of cowl to provide additional clearance. |
| PIP3720D | 2017-08-15. Service bulletin. POWER TRAIN:AXLE ASSEMBLY. This Preliminary Information communication provides information to the technician with the axel setup information from American Axle Manufacturing. Technician should be advised that the maximum pinion shim to be used or stacked behind the pinion is 0.050?, and the minimum pinion shim is 0.020? for an 8.6 axle. The range for available pinion depth shims for the 10.5? axle is 0.006? to 0.024?. When setting the backlash it should be set between 0.003? to 0.005? on a new ring and pinion for any American Axle Manufacturing application. The ring and pinion can be reused or adjusted if the mileage is less than 500 miles, if not used for towing. Technician should be advised that a ?roller coaster? or ?hourglass? pattern on the bearings may be normal up to 10,000 miles and possibly longer. With a mis-machined housing you may get a heel pattern on both sides of the gear teeth at build up can generally be corrected with backlash adjustments. When setting up an 8.6? axle with a 5 cut gear set is to use a 0.035? pinion shim and set backlash to 0.004?. When using the newer 2 cut gear set also use a 0.035? pinion shim and still set backlash to 0.004?. To set the gear pattern use backlash to adjust the pattern heel to toe. Use the pinion shim to adjust the height of the pattern. The proper drive pinion bearing pre-load is from 15 - 30 inch pounds with new bearings. The total torque to turn after the differential case is installed should increase 5 - 10 inch pounds at the pinion. A new pinion nut must be used whenever the old one is removed. The axle shaft end play specification is 0.012? per side and the radial specification is 0.002? - 0.003?. Technician should be advised that synthetic lube can be used in all new American Axle Manufacturing axle assemblies. The new pinion seal for the 8.6? axle assembly is a two piece design. |
| PIT4979C | 2017-08-15. Service bulletin. FUEL SYSTEM, OTHER:DELIVERY:HOSES, LINES/PIPING, AND FITTINGS; FUEL SYSTEM, GASOLINE. This Preliminary Information communication provides information to the technician about vehicles that have a buzz or rattle type noise during light acceleration around 1200-2000 Revolutions per minute. Technician will need to reposition the fuel line and bracket down away from the floor pan. |
| PIT4041D | 2017-08-15. Service bulletin. ELECTRICAL SYSTEM; STRUCTURE:BODY:HATCHBACK/LIFTGATE. This Preliminary Information communication provides information to the technician about vehicles that the power lift gate Regular Production Option Code (E61 or TB5) is inoperative. Technician will find Diagnostic Trouble Code B153A set in the power lift gate control module. Technician will need to perform these steps. 1. Disconnect the connector at the Lift gate Latch Assembly. 2. Install a 3 ampere fused jumper wire between each signal circuit and the ground circuit. 3. If either test fails, check the wiring for the signal circuits, low reference circuit, or try a power lift gate control module from a known good vehicle. 4. If both tests pass, monitor the internal switch inputs in the lift gate latch assembly for proper operation. 5. If one of the internal lift gate latch assembly switch inputs are not reading correctly in one of the positions above and the vehicles passes test both test, replace the Lift Gate Latch Assembly. |
| PIT4907A | 2017-08-15. Service bulletin. SERVICE BRAKES. This Preliminary Information communication provides information to the technician about brake rotors on new vehicles and replacement parts from General Motors Service Parts Operations. Technician should be advised the costing should not be removed from the brake rotor it will wear off with normal brake usage. Dealer should communicate to the customer this condition is a normal operating characteristic of their vehicle. |
| PIT4815C | 2017-08-15. Service bulletin. ELECTRICAL SYSTEM. This Preliminary Information communication provides information to the technician with additional vehicle speed sensor diagnostic information. Technician may encounter multiple issues when diagnosing a Vehicle Speed Sensor. Technician will find it difficult to follow the speed signal path between the components. To test connect the Fluke meter leads between circuits 821 and 822 and set the meter to Alternating current voltage and then press the hertz button. When the Engine Control Module showing correct miles per hour in the data list however it is setting a Diagnostic Trouble Code for the Vehicle Speed Sensor. To test connect the Fluke meter red lead to circuit 6399 and the black lead to ground, then set the meter to Direct current voltage and press the hertz button. The Instrument Panel Cluster speedo will work correctly when the Engine Control Module or Antilock Braking System Diagnostic Trouble Codes are for the Vehicle Speed Sensor. To test connect the Fluke meter red lead to circuit 1827 and the black lead to ground, then set the meter to Direct current voltage and press the hertz button. When the Antilock Braking System Malfunction Indicator Lamp on with Electronic Brake Control Module Diagnostic Trouble Code C0055 and no other customer complaints, to test connect the Fluke meter red lead to circuit 817 and the black lead to ground, then set the meter to Direct current voltage and press the hertz button. |
| PIT4225F | 2017-08-15. Service bulletin. SERVICE BRAKES, AIR:ANTILOCK; SERVICE BRAKES, HYDRAULIC:ANTILOCK/TRACTION CONTROL/ELECTRONIC LIMITED SLIP; SERVICE BRAKES, ELECTRIC. This Preliminary Information communication provides information to the technician about vehicles that have an Antilock Braking System lamp followed by a Service Stability message in the Drivers Information Center. Technician my find Diagnostic Trouble Code C0710 set in the Electronic Brake Control Module. Technician may or may not find Diagnostic Trouble Code C0455. Technician will need to ensure the steering wheel is properly installed to the steering shaft. |
| PIT4208D | 2017-08-15. Service bulletin. SERVICE BRAKES, HYDRAULIC:POWER ASSIST; STEERING:HYDRAULIC POWER ASSIST:POWER STEERING FLUID. This Preliminary Information communication provides information to the technician about vehicles that may have a power steering pump whine noise. Technician will need to flush and refill the power steering system with Lucas Power Steering Fluid with Conditioners. Technician will replace the power steering pump with the latest design if the fluid is not available. |
| PIT4979B | 2017-08-15. Service bulletin. ENGINE AND ENGINE COOLING. This Preliminary Information communication provides information to the technician about vehicles that have a buzz or rattle type noise during light acceleration around 1200-2000 Revolutions per minute. Technician will need to reposition the fuel line and bracket down away from the floor pan. |
| PIC5491A | 2017-08-15. Service bulletin. EQUIPMENT:ELECTRICAL. This Preliminary Information communication provides information to the technician about vehicles that have an OnStar system that will not power up. Technician should turn off the ignition and cancel retained accessory power. After the vehicle has powered down, remove power to the OnStar module for five minutes. After the power has been removed for five minutes, if the OnStar system is working release the vehicle. If the OnStar system is still inoperative continue with published Service Information diagnostics. |
| PIC4935D | 2017-08-15. Service bulletin. ELECTRICAL SYSTEM. This Preliminary Information communication provides information to the technician about vehicles that during battery parasitic drain test, there may be some confusion as to what the normal power consumption reading should be from the OnStar system. Technician should understand the power cycles of the various OnStar systems. All Generation 6, 7, 8, and 9 systems are powered up continuously for 48 hours from ignition off. After 120 hours from ignition off, these systems then completely power off. The Onstar modules draw: * IGN ON - 240 to 400 Milliamp. * IGN OFF - 3 to 20 Milliamp for 48 hours or 120 hours on Gen 9 and vehicle communication platforms. * IGN OFF - 0.2 to 0.8 Milliamp after 48 hours or 120 hours on Gen 9 and vehicle communication platforms. |
| PIT4169F | 2017-08-15. Service bulletin. SERVICE BRAKES, ELECTRIC; EQUIPMENT:ELECTRICAL. This Preliminary Information communication provides information to the technician about vehicles that have a "Service Stability Message" appears on the Drivers Information Center. Technician will find Diagnostic Trouble Code C0561 set in the Electronic Brake Control Module. Technician will need to address any other Diagnostic Trouble Codes that are set in the vehicle first before working on Diagnostic Trouble Code C0561. |
| PIT3078F | 2017-08-15. Service bulletin. WHEELS:HUB; SUSPENSION:FRONT:HUB. This Preliminary Information communication provides information to the technician about vehicles that have grease leaking from front hub bearings. Technician should not replace the bearing for grease purge. Technician should be advised to not clean the purged grease from the area immediately on or adjacent to the seals because this grease provides additional protection. Technician should only replace the bearing if the seals show visible damage, bearing endplay is greater than 0.005" or 0.13mm, bearing exhibits rough rotation, or bearing exhibits abnormal noise. |
| PIT4089H | 2017-08-15. Service bulletin. EQUIPMENT ADAPTIVE/MOBILITY; SEATS. This Preliminary Information communication provides information to the technician about vehicles that are unable to set a personalized easy exit seat and/or power tilt column position and they will only move a predetermined amount. Dealer should communicate to the customer this condition is a normal operating characteristic of their vehicle. |
| PIT4506C | 2017-08-15. Service bulletin. TIRES. This Preliminary Information communication provides information to the technician that some owners of Heavy Duty Trucks and Utilities may ask if they can lower their tire pressures. Tire pressures being set to the "Tire and Loading Label" will ensure the safe handling and ride characteristics of the truck and should not be lowered. |
| PIT3099J | 2017-08-15. Service bulletin. EQUIPMENT ADAPTIVE/MOBILITY. This Preliminary Information communication provides information to the technician about installing General Motors Accessory parts. Technician can check Service Information for some accessories. Technician can also contact Partech for assistance. |
| PIT5185 | 2017-08-15. Service bulletin. ELECTRICAL SYSTEM; ELECTRICAL SYSTEM:IGNITION. This Preliminary Information communication provides information to the technician about vehicles that if the ignition key is turned to the start position, and then released when the engine begins cranking, the engine will continue cranking for a few seconds or until the vehicle starts. Some customers may state that this feature is inoperative. Technician should be advised that if the Low Fuel warning lamp is on and/or the FUEL LEVEL LOW message is displayed in the Driver Information Center, the Computer?Controlled Cranking System will be disabled. |
| PIT5184 | 2017-08-15. Service bulletin. ELECTRICAL SYSTEM; VEHICLE SPEED CONTROL:CRUISE CONTROL; ELECTRICAL SYSTEM:WIRING; EQUIPMENT:ELECTRICAL:RADIO/TAPE DECK/CD ETC.. This Preliminary Information communication provides information to the technician about vehicles that have an instrument panel backlighting flashes, flickers or inoperative, unwanted horn activation, radio controls inoperative or unwanted activation, OnStar unwanted activation, and cruise control inoperative. Technician should inspect for a short to ground on the steering wheel near the Supplemental Inflatable Restraint coil connector X2 and make necessary repairs to any shorted circuits and then position the wiring. |
| PIT3237F | 2017-08-15. Service bulletin. VISIBILITY:GLASS, SIDE/REAR; VISIBILITY:WINDSHIELD. This Preliminary Information communication provides information to the technician about the percentage of Ultraviolet protection or tint offered by the windshield or side glass. Technician should be advised Windshield reduces Ultraviolet rays down to 4% or less. Front side door glass reduces Ultraviolet rays down to 35% or less. Windshields are SOLAR glass with a light transmittance of >/=70%. Front door glass are Solar glass with a light transmission of >/=70%. Rear door glass, quarter windows and back windows can use either Solar glass (>/=70%) or Privacy glass, which has a light transmittance of 20%. |
| PIT4508C | 2017-08-15. Service bulletin. ELECTRICAL SYSTEM: INTEGRATED TRAILER BRAKE CONTROL; ELECTRICAL SYSTEM. This Preliminary Information communication provides information to the technician about vehicles that the cruise control being inoperative. Technician may find Diagnostic Trouble Code B3894 set in the Trailer Brake Control Module. Technician should follow published Service Information diagnostics first. Technician should check the "Master Cylinder Pressure" sensor parameter listed in the Trailer Brake Control Module data list. If it is displaying pressure with no brake pedal input, suspect a concern with the Master Cylinder Pressure Sensor, wiring/terminals, or Electronic Brake Control Module. |
| PIP4568P | 2017-08-15. Service bulletin. ENGINE; FUEL SYSTEM, GASOLINE. This Preliminary Information communication provides information to the technician that some vehicles may have a Service Engine Soon lamp, engine misfire on cylinder 1, 4, 6, or 7 and/or tick noise. Technician will follow service information diagnosis first. If service information diagnosis does not isolate the cause of this concern perform a cylinder deactivation active fuel management system compression test in service information. If the running compression of the misfiring cylinder stays below 25 Pounds per Square Inch regardless of the active fuel management solenoid being commanded on or off, an active fuel management lifter is mechanically collapsed/stuck or unlocking as soon as the engine is started. Replace all active fuel management lifters, and all plastic lifter guides. Also perform the cylinder deactivation active fuel management Valve Lifter Oil Manifold Diagnosis and Testing in Service Information. If it isolates a concern with the Valve Lifter Oil Manifold, replace it and reevaluate the concern. The active fuel management lifters can also be monitored for proper operation by carefully inspecting the cylinder 1, 4, 6, and 7 rockers and valves while cranking or briefly and safely running the engine with the valve covers removed. If the valve or valves of an active fuel management cylinder stop moving while doing this test, the active fuel management lifter is causing the concern. For 2008-2009 Full Size Truck/SUV or a 2007-2009 Chevrolet Tahoe with the Police Package reprogram the Engine Control Module. On the 2008-2009 Pontiac G8, 2010-2011 Camaro, and 2007-2010 Full Size Trucks with active fuel management, also determine if the active fuel management pressure relief valve shield that is listed in the latest version of 10-06-01-008 has ever been installed. On passenger cars with the LS4 engine, determine if the updated oil pan gasket that is listed in the latest version of 11-06-01-007 has been installed. |
| PIT3189R | 2017-08-15. Service bulletin. ELECTRICAL SYSTEM; LATCHES/LOCKS/LINKAGES:DOORS:LATCH; STRUCTURE:BODY:DOOR. This Preliminary Information communication provides information to the technician about customers that are unable to override the automatic door locking feature. Technician will update the Body Control Module on 2006 to 2007 model years. On 2010 to 2014 model years technician will need to contact Techline Customer Support for calibrations. |
The summaries are NHTSA's. Each bulletin's page links NHTSA's copy of the manufacturer's document.