Service bulletins for the 2016 GMC Terrain
A bulletin is a manufacturer's communication to its dealers, as NHTSA indexes it. The summary is NHTSA's. The document is the manufacturer's: read it at NHTSA. A bulletin is not a recall, and listing a model year does not mean every vehicle of it is concerned.
1232 on file from NHTSA, as of 2026-10-19.
By type
By component
By trouble code
By topic
Only bulletins with component: Engine are shown. Show all
| 07-06-04-025L | 2017-08-31. Service bulletin. ENGINE. This informational bulletin provides information on Clicking/Ticking Sound/Noise Heard During Cold Start and that this should be considered a normal characteristic. |
|---|---|
| PIP5232B | 2017-08-15. Service bulletin. ENGINE AND ENGINE COOLING:EXHAUST SYSTEM:EMISSION CONTROL:CATALYTIC CONVERTOR. This Preliminary Information communication provides information to the technician about gasoline powered cars, mid-size trucks, light duty trucks, and heavy duty trucks with premature catalytic converter failures. It is recommended to inspect for a poor crimp on the grounds ring terminal at the engine block for the bank with the concern and repair the wire. |
| PIP5216C | 2017-08-15. Service bulletin. ENGINE. This Preliminary Information communication provides information to the technician about vehicles that have a knock noise, seized engine, lower end squeak or squeal from the engine. Technician will inspect the oil control solenoids for metal debris. Also inspect for damage to the cam caps Journals and camshaft journals on the heads. The check the timing chain idler sprockets for stiffness when turning. If any of these instances would be a cause to replace the engine instead of repair. |
| PIP5277A | 2017-08-15. Service bulletin. SUSPENSION; POWER TRAIN; ENGINE. This Preliminary Information communication provides information to the technician on the steps to diagnose and repair vehicles that have a resonance type vibration occurs between 40 to 60 MPH. In most cases the engine must be under a slight load such as Air Conditioning compressor engagement, light throttle, and in 6th gear Torque Converter Clutch applied. Technician will relax the engine and transmission mounts, then the exhaust system by loosening the front pipe studs. Also work down the system disconnecting one exhaust hanger at a time. Then take the vehicle on a test drive to verify there was improvement. If additional steps are required place two sets of exhaust dampeners one set before and one set after the front catalytic converter. It may be required to move the pair of dampeners along the exhaust system to get the best results. |
| PIP5216B | 2017-08-15. Service bulletin. ENGINE. This Preliminary Information communication provides information to the technician about vehicles that have a knock noise, seized engine, lower end squeak or squeal from the engine. Technician will inspect the oil control solenoids for metal debris. Also inspect for damage to the cam caps Journals and camshaft journals on the heads. The check the timing chain idler sprockets for stiffness when turning. If any of these instances would be a cause to replace the engine instead of repair. |
| PIP5216A | 2017-08-15. Service bulletin. ENGINE. This Preliminary Information communication provides information to the technician about vehicles that have a knock noise, seized engine, lower end squeak or squeal from the engine. Technician will inspect the oil control solenoids for metal debris. Also inspect for damage to the cam caps Journals and camshaft journals on the heads. The check the timing chain idler sprockets for stiffness when turning. If any of these instances would be a cause to replace the engine instead of repair. |
| PIP5257A | 2017-08-15. Service bulletin. ENGINE AND ENGINE COOLING. This Preliminary Information communication provides information to the technician on the steps to diagnose and repair vehicles that may have oil mixed in with the engine coolant. Technician will need to inspect the oil cooler if equipped for possible leaking into the cooling system through the radiator. If no issue found replace the engine as well as all rubber coolant hoses. |
| PIT4943D | 2017-08-15. Service bulletin. FUEL SYSTEM, GASOLINE; FUEL SYSTEM, OTHER:STORAGE:TANK ASSEMBLY; ENGINE AND ENGINE COOLING:EXHAUST SYSTEM:EMISSION CONTROL. This Preliminary Information communication provides information to the technician about vehicles that have a Service Engine Soon Malfunction Indicator Lamp. Technician may find Diagnostic Trouble Code P0442. Technician will need to review Techlink article from May 2013 titled "Using the Evaporative Emissions System Tester" Technician will need to follow these steps to help diagnose the issue. First after the P0442 has been verified do not disturb any of the fuel system components. The technician now can use the scan tool to close the Evaporative Emissions System. If possible change the tank pressure sensor units from inch_H2O to milimeter_Hg for better resolution. Now the vehicle can be stared to monitor the tank pressure sensor output value for approximately two minutes. If the tank pressure sensor value does change, pressurize the fuel tank side of the purge solenoid with the GE 41413-A / J 41413-A and the necessary adaptors. Now add smoke and allow pressure to stabilize for 2 minutes. If smoke is allowed to pass through the purge solenoid, replace the purge solenoid. If the tank pressure sensor value does not change, then install CH-48096 adaptor between the purge line from the canister and the purge solenoid. With the Evaporative Emissions System closed, pressurize the system through the CH-48096 adaptor and allow the system to completely stabilize, by observing the Press / Vac Gauge for a minimum of 5 minutes. Now add smoke to the system with GE 41413-A / J 41413-A after system stabilization. Now inspect the purge solenoid, engine side, fuel cap, canister vent solenoid filter and any line quick connects. When the leak is unable to be located, test under a vacuum condition. his type of leak may be detected by using the scan tool Purge/Seal function to create a vacuum in the Evaporative Emissions System and then observe the FTP sensor parameter for vacuum decay. |
| PIP4548E | 2017-08-15. Service bulletin. ENGINE AND ENGINE COOLING:EXHAUST SYSTEM. This Preliminary Information communication advises the technician what to inspect if codes P0016 and/or P0017 are setting on a properly timed engine or a condition of the vehicle cranks but will not start. Technician should inspect the respective intake or exhaust camshaft reluctor to see if it has spun on the camshaft. The reluctor cannot be repositioned so the camshaft must be replaced. The new camshafts come with the reluctor already pressed on in the correct position. |
| PIP5216D | 2017-08-15. Service bulletin. ENGINE. This Preliminary Information communication provides information to the technician about vehicles that have a knock noise, seized engine, lower end squeak or squeal from the engine. Technician will inspect the oil control solenoids for metal debris. Also inspect for damage to the cam caps Journals and camshaft journals on the heads. The check the timing chain idler sprockets for stiffness when turning. If any of these instances would be a cause to replace the engine instead of repair. |
| PIP3423M | 2017-08-15. Service bulletin. ENGINE; EQUIPMENT ADAPTIVE/MOBILITY. This Preliminary Information communication provides information to the technician that Diagnostic Trouble Codes P0016, P0017, P0018, P0019, P0008 or P0009 may be set. Technician will need to inspect for loose timing chains or tensioners. If after following Service Information diagnostics the root cause is not found inspect the reluctor for the crankshaft sensor. If the reluctor has moved then replace crankshaft. |
| PIP5095C | 2017-08-15. Service bulletin. ELECTRICAL SYSTEM; ENGINE AND ENGINE COOLING. This Preliminary Information communication provides information to the technician about vehicles that have a Service Engine Soon and may also have an oil or coolant leak. Technician may find coolant or oil in a spark plug tube. If the Spark Plug Tube is leaking and it is determined that the oil or coolant is not coming from a leak above the spark plug then replace the cylinder Head, spark plug and coil. |
| PIP5163B | 2017-08-15. Service bulletin. EQUIPMENT ADAPTIVE/MOBILITY; FUEL SYSTEM, GASOLINE; ENGINE. This Preliminary Information communication provides information to the technician about engine block that have a possible cylinder bore damage, scoring or out of round as the possible cause of engine oil consumption, misfire, cylinder leakage or blow by. Technician will need to inspect the engine for Cylinder damage or scoring, an out of round cylinder bore, Dirt intrusion, and Catalytic Converter failure. |
| PI1223B | 2017-08-15. Service bulletin. ENGINE AND ENGINE COOLING:EXHAUST SYSTEM. This informational bulletin provides information on black smoke and rough idle on cold start. |
| 09-06-04-026M | 2017-08-15. Service bulletin. ELECTRICAL SYSTEM:SOFTWARE; ENGINE. This informational bulletin provides information on identifying non-GM (aftermarket) engine calibrations for gasoline engines using Tech 2 or GDS 2. |
| PIP5331B | 2017-08-15. Service bulletin. ENGINE AND ENGINE COOLING. This Preliminary Information communication provides information to the technician that some vehicles may have rattle, tick, or knock type noise. If there are any drivability concerns they should be addressed prior to the following diagnostic progression. Technician will take a sound file or video with sound of the noise prior to dis-assembly. Technician may find this noise hard to isolate to one area in the engine. There are four different steps to take to diagnosis the concern. Technician will perform injector diagnosis to ensure there are no leaking injectors causing a noise due to excessive fuel in any one cylinder. Replace any out of specification injectors the reevaluate for the noise. Technician will remove the intake manifold and visually inspect for excessive carbon on the intake valve stems and top of the valve causing noise. If carbon is present then follow the latest version of PIP5029 to clean the valves or replace heads as needed. Technician will remove the cam cover of the affected bank (both if needed) to inspect for soft or spongy stationary hydraulic lash adjusters. Push down on the rocker end at the stationary hydraulic lash adjusters to test for soft or spongy. If soft or spongy stationary hydraulic lash adjusters are found, carefully remove the affected head and inspect the oil passage below the head gasket for debris. If debris is found, inspect the camshaft caps for wear or discoloration due to lack of oil. During inspection if wear or discoloration is found then replace the cylinder head assembly with camshafts. If there is no wear or discoloration, clean the oil passages and replace the head gasket. Technician will use chassis ears or a stethoscope; listen to the right and left side of the engine. Once the noise is isolated or if unable to isolate, remove the piston and rod assemblies from the affected bank(s) to inspect for either; a loose rod bushing in the rod, or a loose wrist pin in the bushing. If this is found, replacing the piston an |
| PIP5232C | 2017-08-15. Service bulletin. ENGINE AND ENGINE COOLING:EXHAUST SYSTEM:EMISSION CONTROL:CATALYTIC CONVERTOR. This Preliminary Information communication provides information to the technician about gasoline powered cars, mid-size trucks, light duty trucks, and heavy duty trucks with premature catalytic converter failures. It is recommended to inspect for a poor crimp on the coil grounds ring terminal at the engine block for the bank with the concern and repair the wire. |
| 00-06-01-026G | 2017-08-15. Service bulletin. ENGINE AND ENGINE COOLING. This informational bulletin provides information to technicians regarding intake manifold inspection/replacement after severe internal engine damage. |
| 15-00-89-004A | 2017-08-15. Service bulletin. ENGINE AND ENGINE COOLING. This informational bulletin provides technicians with updated information to help identify the differences between what is considered a fluid leak, and what is considered seepage. |
| 00-06-01-026F | 2017-08-15. Service bulletin. ENGINE AND ENGINE COOLING. This informational bulletin provides information to technicians regarding intake manifold inspection/replacement after severe internal engine damage. |
| PIP5095D | 2017-08-15. Service bulletin. ENGINE AND ENGINE COOLING; ELECTRICAL SYSTEM. This Preliminary Information communication provides information to the technician about vehicles that have a Service Engine Soon and may also have an oil or coolant leak. Technician may find coolant or oil in a spark plug tube. If the Spark Plug Tube is leaking and it is determined that the oil or coolant is not coming from a leak above the spark plug then replace the cylinder Head, spark plug and coil. |
| PIP5331D | 2017-08-15. Service bulletin. ENGINE. This Preliminary Information communication provides information on a rattle, tick, or knock type noise. Any drivability concerns they should be addressed prior to the following diagnostic progression. A sound file or video with sound of the noise needs to be made prior to dis-assembly to help isolate to one area in the engine. There are four different steps to diagnosis the concern. This communication was updated to include the 2017 model year. |
| PIP5029H | 2017-08-15. Service bulletin. ENGINE. This Preliminary Information communication provides information to the technician about vehicles that have a Malfunction Indicator Lamp on or engine misfire, rough idle, extended crank, or crank no start in some cases. Technician will need to perform published Service Information diagnostics. If technician finds carbon, an upper engine and valve cleaning should be performed. Update added part numbers for the cleaner and model years. |
| PIP5180A | 2017-08-15. Service bulletin. ENGINE AND ENGINE COOLING; ENGINE AND ENGINE COOLING:EXHAUST SYSTEM. This Preliminary Information communication provides information to the technician about vehicles that have hard start, extended crank, or black smoke from the exhaust when starting. Technician will need to perform fuel quality test, spark test, and a compression test. Technician should also install a vacuum gauge prior to cold start and watch needle for signs of a sticking valve. Technician will need to review the latest version of PIP5029 and perform a cold compression test if the concern is only a Hard Start Cold. |
| PI1250D | 2017-08-15. Service bulletin. ENGINE. This preliminat informational bulletin provides information on the proactive alert advanced diagnostics. Proactive Alert monitors the Engine Cranking system and the Fuel Delivery system and if either one of these monitored systems triggers certain performance issues, specific Customer and Dealer Communication are sent. |
The summaries are NHTSA's. Each bulletin's page links NHTSA's copy of the manufacturer's document.