WenmarOpen by Wenmar Pro

Service bulletins for the 2019 Freightliner Sprinter

A bulletin is a manufacturer's communication to its dealers, as NHTSA indexes it. The summary is NHTSA's. The document is the manufacturer's: read it at NHTSA. A bulletin is not a recall, and listing a model year does not mean every vehicle of it is concerned.

111 on file from NHTSA, as of 2026-10-19.

By type

By component

By trouble code

By topic

Only bulletins with component: Electrical system are shown. Show all

Bulletins, newest first
20250800082025-10-07. Service campaign. ELECTRICAL SYSTEM. Mercedes-Benz AG, the manufacturer of Sprinter vehicles, has determined that on certain Freightliner Sprinter (907 platform) vehicles, has determined the software of the control unit for the anti-theft warning system does not correspond to the current production configuration. There is a possibility that the alarm system (EDW) could be triggered while the vehicle is parked and locked. DVUSA is conducting a service campaign. An authorized Freightliner Sprinter dealer will update the anti-theft system software on the affected vehicles.
LI49.20-N-079157_62025-07-01. Service bulletin. ELECTRICAL SYSTEM. Complaint The check engine light is activated, accompanied by one or more of the following fault codes related to the Adblue System: •P20F409: The Adblue consumption is too low. There is a component fault. •P202E84: The Adblue metering valve 1 (Motor side) has a malfunction. There is a signal below the permissible limit value. Cause The potential causes for these fault codes are: A. A leak in the Adblue System B. An internal fault with the Adblue Injection Valve #1 (Motor side) C. An air pocket forming in the Adblue Injection Valve #1 (Motor side) Adblue Injector Line Remedy Vehicles Produced Before August 1, 2024 (Code XY4 = MY24) A. Leak in the AdBlue System 1. Complete the Guided Tests for DTC P20F409 or P202E84: •Inspect the AdBlue tank, pump, line, and both injectors for leaks. •Ensure the AdBlue line is properly routed, securely fastened, and not in contact with the exhaust system. •Remove both AdBlue injection valves, perform 2–3 pressure build-ups, and check for AdBlue leaks. •If a leak is detected, repair it and retest. B. Internal Fault with AdBlue Injection Valve #1 (Motor Side) 1. Process All Other Related DTCs First: •Address any other fault codes relating to AdBlue injection valves before proceeding. •If AdBlue Injection Valve #1 (engine side) fails the guided tests, replace it and retest. C. Air Pocket Forming in the AdBlue Line (Motor Side) 1. If Guided Tests Pass and No Leaks are Found: --Do not replace any components.-- •The MY23-24 (Code XY4 = MY24, OM654) AdBlue line (A907 470 01 01) has a known design issue that can cause air pockets and DTC P20F409. This may also result in DTC P202E84, depending on the air pocket size. •The guided tests for P20F409 now include resetting the learned values for the AdBlue delivery pump (A103m1). After this, the vehicle can be released to the customer. NOTE: Replacing the AdBlue tank or line will NOT resolve this air pocket issue. TIPS cases are no longer required for MY23–24 vehicles. Steps to Perform (MY23–24, Code XY4): 1. Complete the guided tests for DTC P20F409 and/or P202E84. 2. Perform an initial start-up of: •The SCR control unit •AdBlue tank components •Both AdBlue injectors 3. Conduct a 20-mile test drive. If no faults occur, the vehicle can be released. 4. Inform the customer that frequent starting/stopping increases the likelihood of this fault due to repeated cycling of AdBlue in/out of the line each ignition cycle. Vehicles Produced After August 1, 2024 (Code XY5 = MY25) A. Leak in the AdBlue System 1. Complete the Guided Tests for DTC P20F409 or P202E84: •Inspect the AdBlue tank, pump, line, and both injectors for leaks. •Ensure the AdBlue line is properly routed, securely fastened, and not in contact with the exhaust system. •Remove both AdBlue injection valves, perform 2–3 pressure build-ups, and check for AdBlue leaks. •If a leak is detected, repair it and retest. B. Internal Fault with AdBlue Injection Valve #1 (Motor Side) 1. Process All Other Related DTCs First: •Address any other fault codes relating to AdBlue injection valves before proceeding. •If AdBlue Injection Valve #1 (engine side) fails the guided tests, replace it and retest. C. Incorrect AdBlue Injection Line Installed 1. Verify the Updated Line is Installed: •Confirm that part number A907 470 33 02 is present. •If the AdBlue line is incorrect (e.g., A907 470 01 01), replace it with the updated line. TIPS Case Instructions for All MY25 and Newer Vehicles If you encounter any of the issues above on any MY25 or newer vehicle, including finding an incorrect AdBlue line in- stalled: •Open a TIPS case addressed to the Powertrain inbox. •Reference this LI document. •Include the following information: •Description of the issue encountered (e.g., fault code, check engine light, or incorrect AdBlue injection line) •Current Quick Test, SCR N118/5 Control Unit Log, and Guided Test results. •Photo of AdBlue line part number label. •Photos documenting any issues, leaks, or melting observed
LI47.70-N-079422_12025-07-01. Service bulletin. ELECTRICAL SYSTEM. HV battery is not charging to its full capacity with restricted maximum SoC Complaint The vehicle's HV battery is not charging to its full capacity, with the maximum State of Charge (SoC) being restricted to a specific percentage. Cause The State of Charge (SoC) percentage limitation might be influenced by the Onboard Logic Unit (OLU), MBUX Headunit, or the Powertrain Control Unit (PTCU). Remedy If the Onboard Logic Unit (OLU) and MBUX Headunit do not impose a SoC percentage limitation, then proceed with the SCN coding of the Powertrain Control Unit (PTCU).
LI88.30-N-0780362024-08-03. Service bulletin. ELECTRICAL SYSTEM. Complaint T57 Electric step inoperative with warning on cluster. Cause Possible damage to end position sensors.
News Channel Upd2023-07-31. Service bulletin. ELECTRICAL SYSTEM; ENGINE AND ENGINE COOLING. Modify Interior Blower Motor Fuse Layout
News Channel Upd2023-05-22. Service bulletin. ELECTRICAL SYSTEM:SOFTWARE. Update Instrument Cluster Software
FTL Initial NCU2023-03-27. Service bulletin. ELECTRICAL SYSTEM; ENGINE AND ENGINE COOLING. Modify Interior Blower Motor Fuse Layout
22V2790611-12023-03-06. Service bulletin. POWER TRAIN; ELECTRICAL SYSTEM. (RC)Update Park Lock Function
NCU-VS3SIMKOM-12023-01-03. Service bulletin. ELECTRICAL SYSTEM. (RC)Update Hermes Communication Module Software
Updates2022-08-08. Service bulletin. ELECTRICAL SYSTEM. (RC)Update Hermes Communication Module Software
Recall2022-06-27. Service bulletin. BACK OVER PREVENTION; ELECTRICAL SYSTEM:ADAS:DRIVER MONITORING:SOFTWARE. Update Rear View Camera Software
Software2022-06-27. Service bulletin. ELECTRICAL SYSTEM:ADAS:DRIVER MONITORING:SOFTWARE; BACK OVER PREVENTION. Update Rear View Camera Software
Recall Campaign2022-05-31. Service bulletin. ELECTRICAL SYSTEM:SOFTWARE. Ecall Hermes Software Update.
20211200092022-05-31. Service bulletin. ELECTRICAL SYSTEM:SOFTWARE. Software updare.
News Channel Upd2022-02-23. Service bulletin. ELECTRICAL SYSTEM:SOFTWARE. Update ESP Software
Initial NCU - 902020-07-13. Service bulletin. SEATS; ELECTRICAL SYSTEM:WIRING. Swivel Seat Mercedes-Benz AG (“MBAG”), the manufacturer of Mercedes-Benz and Freightliner vans, has determined that on certain Sprinter vehicles from platform 907 (VS30) that are equipped with front swivel-seats, the electric cables in the seat wiring harness could become jammed and damaged in the swivel-seat frame. If electric cables in the wiring harness become jammed and damaged in the swivel-seat frame, the operation of the side airbag within the seat could be adversely affected which could cause the side airbag to deploy inadvertently or not deploy as designed in the event of a crash, increasing the risk of injury to vehicle occupants.

The summaries are NHTSA's. Each bulletin's page links NHTSA's copy of the manufacturer's document.