WenmarOpen by Wenmar Pro

Service bulletins for the 2020 Ford Mustang

A bulletin is a manufacturer's communication to its dealers, as NHTSA indexes it. The summary is NHTSA's. The document is the manufacturer's: read it at NHTSA. A bulletin is not a recall, and listing a model year does not mean every vehicle of it is concerned.

184 on file from NHTSA, as of 2026-10-19.

By type

By component

By trouble code

Only bulletins with component: Engine are shown. Show all

Bulletins, newest first
SSM 525422024-05-23. Service bulletin. ENGINE. Some 2020-2022 Mustang GT500 vehicles may exhibit a lack of power and/or an illuminated malfunction indicator lamp (MIL) with diagnostic trouble code (DTC) P1228. This may be due to the one-way clutch on the supercharger drive assembly. With the supercharger belt removed, a failed one-way clutch within the pulley rotates freely in both directions. The supercharger drive assembly KR3Z-6J022-B is now available as a lower level service part, separate from the supercharger assembly. Refer to the parts catalog and Workshop Manual (WSM), Section 303-12 for installation.
SSM 525022024-05-17. Service bulletin. ENGINE. Some 2020-2022 Mustang GT500 vehicles may exhibit a lack of power and/or an illuminated malfunction indicator lamp (MIL) with diagnostic trouble code (DTC) P1228. This may be due to the one-way clutch on the supercharger drive assembly. With the supercharger belt removed, a failed one-way clutch within the pulley rotates freely in both directions. The supercharger drive assembly KR3Z-6J022-B is now available as a lower level service part, separate from the supercharger assembly. Refer to the parts catalog and Workshop Manual (WSM), Section 303-12D for installation.
SSM 523352024-03-20. Service bulletin. ENGINE AND ENGINE COOLING. For 2015-2024 Ford and Lincoln vehicles equipped with turbocharged engines and customer concern of an engine oil leak, refer to Workshop Manual (WSM), Section 303-00 for oil leak inspection and testing methods. Ford has evaluated turbochargers replaced for oil leak symptoms and although oil may collect on the external surface of a turbocharger, it is extremely rare for a turbocharger assembly to be the root cause of the oil leak. Careful inspection of the turbocharger oil feed and drain tubes should be performed along with the recommended WSM procedures as needed. Warranty claims for turbocharger replacement going forward will be assessed.
SSM 523342024-03-20. Service bulletin. ENGINE AND ENGINE COOLING. Some 2011-2024 Mustang and F-150 vehicles equipped with a 5.0L engine may exhibit a tick tap and/or typewriter ticking noise at idle after an engine oil change. It is often referred to as typewriter noise because of its similarity to the sound of a mechanical typewriter. The noise in question may be heard on some engines when engine temperatures reach 150°F (65°C) or higher and engine speed is at idle up to approximately 1700 RPM. It can typically be heard at the front wheel well and is often isolated to the transmission bell housing or oil pan area. The typewriter noise tick rate can be faster or slower and is not detrimental to the engine function or durability and has no short or long term effects on the engine. This an operating characteristic of the 5.0L engine and no repairs should be attempted. This information along with an example audio clip has been added to the WSM Section 303-00 Engine System General Information > Diagnosis and Testing > Engine > PPT F > Step F2.
TSB 23-21322023-05-31. Service bulletin. ENGINE AND ENGINE COOLING:EXHAUST SYSTEM. Some 2018-2023 Mustang vehicles (non-Shelby GT-350) may exhibit various concerns with the active exhaust system. These may include Exhaust Mode Selection Not Available messages, and/or illuminated malfunction indicator lamp (MIL) with diagnostics trouble codes (DTCs) P26C5, P26C6, P26FE, P2BF9, P2BFB, P26C7, P2BF5, P2BF8, P2BFD and/or P2BFA. This may be due to an improperly seated exhaust system. To correct the condition, follow the Service Procedure to diagnose the tailpipe actuator.
TSB 22-22822022-10-31. Service bulletin. ENGINE AND ENGINE COOLING:EXHAUST SYSTEM. Some 2018-2022 Mustang vehicles (non-Shelby GT-350) may exhibit various concerns with the active exhaust system. These may include Drive Mode Not Available or Exhaust Mode Not Available messages, and/or illuminated malfunction indicator lamp (MIL) with diagnostics trouble codes (DTCs) P26C5, P26C6, P26FE, P2BF9, P2BFB, P26C7, P2BF5, P2BF8, P2BFD and/or P2BFA. This may be due to an improperly seated exhaust system. To correct the condition, follow the Service Procedure to diagnose the tailpipe actuator .
TSB 22-21402022-04-26. Service bulletin. ENGINE AND ENGINE COOLING; EQUIPMENT; EQUIPMENT ADAPTIVE/MOBILITY. Some 2015-2020 Mustang Shelby GT350/GT350R vehicles may exhibit a hesitation or surge in the vehicle with no diagnostic trouble codes (DTCs) present. This may be accompanied by an inoperative cruise control system. This may be due to a transmission output shaft flange nut that has come loose, allowing the output shaft tone ring to move in relation to the output shaft causing an erroneous signal. To resolve the condition, follow the Service Procedure steps to replace the output shaft flange nut.
SSM 505782022-03-15. Service bulletin. EQUIPMENT; ENGINE AND ENGINE COOLING; EQUIPMENT ADAPTIVE/MOBILITY. Some 2020-2021 Mustang GT500 vehicles may exhibit a lack of power and/or an illuminated malfunction indicator lamp (MIL) with diagnostic trouble code (DTC) P1228. This may be due to the one-way clutch on the supercharger drive assembly. With the supercharger belt removed, a failed one-way clutch within the pulley rotates freely in both directions. The supercharger drive assembly KR3Z-6J022-B is now available as a lower level service part, separate from the supercharger assembly. Refer to the parts catalog and Workshop Manual (WSM), Section 303-12D for installation.
TSB 21-23902021-12-02. Service bulletin. POWER TRAIN; ENGINE AND ENGINE COOLING. Some 2020-2021 Mustang GT500 vehicles built on or before 30-June-2021 may exhibit a no crank/no start with no powertrain control module (PCM) communication condition if the oil level is approximately 1 or more quarts low and the oil life is at or less than 20%. This may be due to various parameters within the PCM. To correct the condition, follow the Service Procedure to reset and reprogram the PCM.
SSM 501032021-09-28. Service bulletin. POWER TRAIN:AUTOMATIC TRANSMISSION:CONTROL MODULE (TCM/PCM/TECM); ENGINE AND ENGINE COOLING. Some 2020 Mustang vehicles equipped with a 5.0L engine built on 01-Sep-2020 and through 01-Dec-2020 may experience an illuminated malfunction indicator lamp (MIL) with diagnostic trouble code (DTC) P0369 in the powertrain control module (PCM). This may be due to a flatness concern on the mega cap on the right hand cylinder head. To correct the condition, replace the right-hand cylinder head. Refer to Workshop Manual (WSM), Section 303-01B > Removal and installation > Cylinder Head RH. For claiming, use causal part 6049 and applicable labor times in Section 06 of the Service Labor Time Standards (SLTS) Manual.
SSM 500892021-09-28. Service bulletin. ENGINE AND ENGINE COOLING; FUEL SYSTEM, GASOLINE. Some 2017-2021 Ford and Lincoln vehicles equipped with 3.3L, 3.5L EcoBoost, or 5.0L engines may exhibit stalling, lack of power, low fuel rail pressure and/or DTCs P0087 or P008A after a repair was made that required the removal of the fuel line that connects the high-pressure fuel pump to the port injection rail, such as injector replacements or base engine repairs. This line must be installed in the correct orientation as it has an internal one-way check valve. To determine if the fuel line has been installed improperly, look at the position of the Oetiker clamp (stainless band clamped around the black fuel line). The clamp holds the one-way check valve in place and should be located closest to the end connected to the port injection rail. If the clamp is not closest to the port injection rail, remove and reinstall the line in the proper orientation.
21B26-S12021-07-01. Service bulletin. ENGINE AND ENGINE COOLING. In some of the affected vehicles, the engine's secondary timing chain tensioner may not have been properly activated during assembly, which could result in a timing loss. Timing loss could lead to internal engine damage, a rough running engine , and engine misfires.
21B262021-06-03. Service bulletin. ENGINE AND ENGINE COOLING. Certain 2020 Model Year Mustang GT500/GT350 Equipped with a 5.2L Engine Secondary Timing Chain Tensioner
SSM 498212021-06-01. Service bulletin. POWER TRAIN:AUTOMATIC TRANSMISSION; ENGINE AND ENGINE COOLING. Some 2015-2021 Ford and Lincoln vehicles may exhibit an illuminated MIL with diagnostic trouble codes (DTC) P0011, P0012, P0014, P0015, P0016, P0017, P0018, P0019, P0021, P0022, P0024 and/or P0025. This may be due to small debris causing the VCT solenoid to stick. Before attempting any component diagnosis or replacement of the VCT solenoid, refer to Powertrain Control and Emissions Diagnosis (PC/ED) pinpoint test HK11 to cycle the affected VCT solenoid 10 times to attempt to clear the debris. For claiming, use causal part 6M280 and applicable labor operations in Section 10 of the Service Labor Time Standards (SLTS) Manual.
21B262021-05-04. Service bulletin. ENGINE AND ENGINE COOLING. Certain 2020 Model Year Mustang GT500/GT350 Equipped with a 5.2L Engine Secondary Timing Chain Tensioner In some of the affected vehicles, the engines secondary timing chain tensioner may not have been properly activated during assembly, which could result in a timing loss. Timing loss could lead to internal engine damage, a rough running engine, and engine misfires.
SSM 497612021-05-03. Service bulletin. ENGINE AND ENGINE COOLING. Some 2011-2021 Mustang and F-150 vehicles equipped with a 5.0L engine may exhibit a ticking noise at idle after an engine oil change. It is often referred to as typewriter noise because of its similarity to the sound of a mechanical typewriter. The noise in question may be heard on some engines when engine temperatures reach 150F (65Å’C) or higher and engine speed is at idle up to approximately 1700 RPMs. It can typically be heard at the front wheel well and is often isolated to the transmission bell housing or oil pan area. The typewriter noise is not detrimental to the engine function or durability and has no short or long term effects on the engine. This an operating characteristic of the 5.0L engine and no repairs should be attempted.
SSM 492102020-10-06. Service bulletin. ENGINE AND ENGINE COOLING. Some 2009-2020 Ford and Lincoln vehicles equipped with turbochargers may exhibit an oil leak from the turbocharger oil supply or return tubes, O-rings or 6.7L pedestal gasket. Although oil may collect on the turbocharger, it is very rare for a turbocharger to leak oil. To isolate the source of the leak, refer to Workshop Manual (WSM), Section 303-00 General Information > Diagnosis and Testing > Engine > Engine Oil Leaks - Fluorescent Oil Additive Method procedure. When an oil leak is present at a turbocharger oil supply or drain tube, remove the affected oil tube and inspect for damage, and replace the O-ring seals, pedestal gasket or oil tube as required. Refer to WSM, Section 303-04. For claiming, use the affected oil tube or pedestal gasket as the causal part and applicable labor operations in Sections 6 and 9 of the Service Labor Time Standards (SLTS) Manual.
SSM 490852020-09-04. Service bulletin. ELECTRICAL SYSTEM; EQUIPMENT; ENGINE. Some 2020 Ford and Lincoln vehicles equipped with a TCU may exhibit incomplete user authorization, no authorization pop-up on the SYNC infotainment system, vehicle connectivity concerns, vehicle location disabled message and/or various FordPass/LincolnWay App command/control concerns. To correct these conditions, ensure that customer connectivity settings (CCS) are turned on in the SYNC system. If the concerns persist after CCS is turned on, turn CCS OFF, perform an ignition cycle, and turn CCS settings back on. After any CCS changes, force-close and relaunch the FordPass/ LincolnWay app on the customers phone. Once CCS is turned on, program the TCU to the latest IDS/FDRS version level. If the concern is still present, follow normal diagnostics in Workshop Manual (WSM), Section 415-00. Refer to PTS OASIS home page for TCU version identification. For claiming, use causal part 14G229.
SSM 490442020-09-04. Service bulletin. ENGINE AND ENGINE COOLING. Some 2020 Mustang vehicles may exhibit a concern of being unable to crank the engine. This will be accompanied by a B1026 DTC and a message in the instrument cluster indicating a steering lock module fault. This may be due to a fault with the body control module (BCM) software. Reprogram the BCM to correct this condition. Refer to Workshop Manual (WSM), Section 419-10. For claiming, use causal part 15604 and any applicable labor operations in Section 10 of the Service Labor Time Standards (SLTS) Manual.
SSM 491322020-09-02. Service bulletin. EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL; ENGINE AND ENGINE COOLING:EXHAUST SYSTEM:MANIFOLD/HEADER/MUFFLER/TAIL PIPE. Some 2020 Mustang GT500 vehicles may exhibit various concerns with the exhaust tailpipe actuators. Workshop Manual (WSM) diagnostics have recently been updated to assist in better diagnosis of these concerns. Refer to WSM, Section 303-14D.
SSM 486512020-04-02. Service bulletin. ELECTRICAL SYSTEM; ENGINE AND ENGINE COOLING. SSM 48651 - 2020 Mustang - No Start With Steering Lock Malfunction Message And Body Control Module (BCM) DTC B1026 Some 2020 Mustang vehicles may exhibit a no start with a Steering Lock Malfunction message on the Instrument Panel Cluster (IPC) and diagnostic trouble code (DTC) B1026 in the BCM. Prior to following workshop manual (WSM) diagnostics, disconnect the negative battery cable per WSM section 414-01, wait 10 seconds and reconnect. After battery reconnect, cycle the ignition key 3 times and retest for no start, steering lock malfunction message and DTC B1026 in the BCM. If the concern is resolved without DTC returning, no further repairs are necessary and engineering is currently investigating this condition. Continue to monitor OASIS for further details. If concern and/or DTC return, refer to WSM section 211-05 for normal diagnostics.

The summaries are NHTSA's. Each bulletin's page links NHTSA's copy of the manufacturer's document.