WenmarOpen by Wenmar Pro

Service bulletins for the 2017 Ford Fusion

A bulletin is a manufacturer's communication to its dealers, as NHTSA indexes it. The summary is NHTSA's. The document is the manufacturer's: read it at NHTSA. A bulletin is not a recall, and listing a model year does not mean every vehicle of it is concerned.

272 on file from NHTSA, as of 2026-10-19.

By type

By component

By trouble code

By topic

Only bulletins with component: Electrical system are shown. Show all

Bulletins, newest first
SSM 474242018-09-10. Service bulletin. ELECTRICAL SYSTEM. Some 2017-2018 Continental, MKC, MKX, MKZ, and Fusion vehicles with an instrument panel center mounted speaker and 2017-2018 Escape vehicles with Sony audio systems may exhibit an inoperative speed compensated volume feature. This may be due to the calibration in the audio control module (ACM). To correct the concern, reprogram the ACM to the latest calibration using the appropriate Ford scan tool release 110.03 or higher. Make sure you are connected to the internet when entering module programming to obtain the latest updates. For claiming, use causal part 18C869 and applicable labor operations in Section 10 of the Service Labor Time Standards (SLTS) Manual.
tsb18-22162018-09-10. Service bulletin. ELECTRICAL SYSTEM:12V/24V/48V BATTERY; EQUIPMENT. Some 2012-2018 Focus Electric, 2013-2017 C-Max Energi, and 2013-2018 Fusion Energi plug-in hybrid electric vehicles (PHEV) may exhibit the high voltage (HV) battery failing to charge while connected to the second Generation 120-volt electric vehicle service equipment (EVSE) charge cord. Follow the Service Procedure steps to correct the condition.
SSM 473802018-07-23. Service bulletin. EQUIPMENT; EQUIPMENT ADAPTIVE/MOBILITY; ELECTRICAL SYSTEM. Some 2016-2018 Ford and Lincoln vehicles with SYNC 3 may exhibit an intermittent blue or black screen. Check for SYNC software update under the OASIS Tab SYNC selection. If update is available refer to WSM, Section 415-00 and update APIM software. After Installation Complete pop-up appears, remove USB flash drive and install into IDS tool to update Ford database. Perform a complete ignition cycle by turning the key off for 5 minutes which is critical for a successful installation. If no updates are available or a blue or black screen is present after an update refer to WSM, Section 415-00 for diagnosis or SYNC 3 intermittent blank screen GSB for tips. For claiming, use causal part 14G371 and applicable labor operations in section 10 of the SLTS manual.
SSM 473792018-07-23. Service bulletin. ELECTRICAL SYSTEM; EQUIPMENT. Various 2016-2018 vehicles with SYNC 3 may experience a touch screen that does not respond to any input. Using the Professional Technician Society (PTS) website > OASIS tab > SYNC version, verify the vehicle SYNC software version. If the vehicle is at version 2.2 please update the module to the latest software level. After the software is updated make sure you shut the vehicle off, open the door for 2 minutes, then turn the key back on before testing the touch screen. If the software is at a later version than 2.2, proceed with normal diagnostics in Workshop Manual (WSM), Section 415-00. For claiming, use causal part 14G371 and applicable labor operations in section 10 of the Service Labor Times Standards (SLTS) manual.
SSM 470412018-06-11. Service bulletin. EQUIPMENT; ELECTRICAL SYSTEM:SOFTWARE; EQUIPMENT:ELECTRICAL; ELECTRICAL SYSTEM. Various 2016-2017 vehicles with SYNC 3 may experience a touch screen that does not respond to any input. Using the Professional Technician Society (PTS) website > OASIS tab > SYNC version, verify the vehicle SYNC software version. If the vehicle is at version 2.2 please update the module to the latest software level. After the software is updated make sure you shut the vehicle off, open the door for 2 minutes, then turn the key back on before testing the touch screen. If the software is at a later version than 2.2, proceed with normal diagnostics in Workshop Manual (WSM), Section 415-00. For claiming, use causal part 14G371 and applicable labor operations in section 10 of the Service Labor Times Standards (SLTS) manual.
SSM 470072018-06-11. Service bulletin. WHEELS; ELECTRICAL SYSTEM:12V/24V/48V BATTERY; TIRES. The EV Range after fully charging a Focus Electric, C-MAX/Fusion Energi may vary after each charge event. The window sticker indicates 0-20 mile range for C-MAX Energi, 0-21 mile range for Fusion Energi. Variation of EV range may not indicate a battery or charging concern. EV range is similar to the DTE display on gasoline vehicles, EV range will vary with driving/operating conditions. Conditions include: extreme outside temperatures, terrain, driving style, city or highway driving, tire pressure, and use of accessories. If the customer replaces the low roll resistance tires with a more aggressive tread the range will suffer. Using the cabin heater and A/C, which are electric, will also decrease EV range. To temporarily remove the impact of driving/climate history , reset the Driving History/Lifetime Summary by using the Settings menu on the left side of the instrument cluster, under Display
SSM 470072018-05-29. Service bulletin. ELECTRICAL SYSTEM. The EV Range after fully charging a Focus Electric, C-MAX/Fusion Energi may vary after each charge event. The window sticker indicates 0-20 mile range for C-MAX Energi, 0-21 mile range for Fusion Energi. Variation of EV range may not indicate a battery or charging concern. EV range is similar to the DTE display on gasoline vehicles, EV range will vary with driving/operating conditions. Conditions include: extreme outside temperatures, terrain, driving style, city or highway driving, tire pressure, and use of accessories. If the customer replaces the low roll resistance tires with a more aggressive tread the range will suffer. Using the cabin heater and A/C, which are electric, will also decrease EV range. To temporarily remove the impact of driving/climate history , reset the Driving History/Lifetime Summary by using the Settings menu on the left side of the instrument cluster, under Display
SSM 471982018-05-21. Service bulletin. ELECTRICAL SYSTEM. Some 2013-2017 Fusion Energi, 2012-2017 Focus Electric and 2013-2017 C-MAX Energi vehicles equipped with a TCU built on or before 11-Oct-2017 may exhibit a discharged battery, inoperative remote features via MyFord Mobile app, incomplete user authorization and/or accessory protocol interface module (APIM) DTC U0198 with no modem electronic serial number (ESN) displayed. To correct this condition, perform any open TCU field service actions (FSAs). If U0198 DTC still remains, remove the TCU fuse for 5 minutes then reinstall. Reprogram the TCU using IDS or Ford J2534 Diagnostic Software (FJDS) release 108.05 or higher. An internet connection is required. Calibration files may also be obtained at www.motorcraftservice.com. For claiming, use causal part 14G229 and applicable labor operations in section 10 of the SLTS manual
SSM 471672018-05-21. Service bulletin. ELECTRICAL SYSTEM. Various 2016-2017 vehicles with SYNC 3 may experience a touch screen that does not respond to any input. Using the Professional Technician Society (PTS) website > OASIS tab > SYNC version, verify the vehicle SYNC software version. If the vehicle is at version 2.2 please update the module to the latest software level. After the software is updated make sure you shut the vehicle off, open the door for 2 minutes, then turn the key back on before testing the touch screen. If the software is at a later version than 2.2, proceed with normal diagnostics in Workshop Manual (WSM), Section 415-00. For claiming, use causal part 14G371 and applicable labor operations in section 10 of the Service Labor Times Standards (SLTS) manual.
SSM 471302018-05-21. Service bulletin. ELECTRICAL SYSTEM: INSTRUMENT CLUSTER/PANEL. Some 2012-2018 Focus Electric, 2013-2017 C-Max Energi, and 2013-2018 Fusion Energi plug-in hybrid electric vehicles (PHEV) may exhibit the high voltage (HV) battery failing to charge while connected to the Delphi 120 volt electric vehicle service equipment (EVSE) charge cord. To identify a Delphi EVSE the coupler on the EVSE that connects to the vehicle charge port is solid black. For information on the Delphi EVSE indicator status used for diagnostics, reference High Voltage Battery > Charging the High Voltage Battery in the Owners Guide for a 2018 Fusion Energi. Reference the Convenience Cord Light Emitting Diode (LED) Indicators chart. The Workshop Manual (WSM) is scheduled to be revised at a later date.
SSM 471292018-05-21. Service bulletin. ELECTRICAL SYSTEM. Some 2013-2017 C-MAX Energi, 2013-2018 Fusion Energi, 2013-2018 C-MAX/Fusion Hybrid/MKZ Hybrid may exhibit a no start with battery energy control module (BECM) diagnostic trouble code (DTC) P0AE5. For 2015-2017 C-MAX Energi refer to the 2014 MY C-MAX Workshop Manual (WSM), Section 414-03A for normal diagnostics. For all vehicles, if WSM pinpoint testing for BECM DTC P0AE5 finds the DC/DC converter control module (14B227), cabin coolant heater (18K463) or A/C compressor (19703) has low high voltage circuit internal resistance, only replace the component found with low internal resistance. It is not necessary to replace the high voltage battery junction (10C666) along with the low resistance high voltage component. The WSM is currently under revision.
SSM 470702018-05-14. Service bulletin. ELECTRICAL SYSTEM:12V/24V/48V BATTERY. When connecting the Vehicle Communication Module (VCM) and Integrated Diagnostic System (IDS) or Ford Diagnosis and Repair System (FDRS) to the DLC located on the driver side under the steering column at the GWM, make sure that the ignition is off before connecting the VCM. If the ignition is on or the engine is running during the connection, it can result in various warning lights being illuminated with diagnostic trouble codes (DTCs), no start or no crank conditions or the IPC inoperative. For Lincoln vehicles, this information is now listed in the Technical Inspection and Post Road Test Sections of ePDI on the PTS website. If a vehicle displays these issues, disconnect the equipment from the DLC and disconnect the vehicle battery. Wait 10 minutes and reinstall with the ignition off. Clear any DTCs present and retest.
SSM 469472018-01-29. Service bulletin. EQUIPMENT; BACK OVER PREVENTION; ELECTRICAL SYSTEM; LANE DEPARTURE. Some 2016-2017 Ford and Lincoln vehicles with SYNC 3 may intermittently display an overhead image of a vehicle in the center of the SYNC touchscreen with no obstacle detection grids or warning chimes. SYNC may appear unresponsive when the overhead vehicle image is displayed. The vehicle image may intermittently display after shifting out of reverse or turning the vehicle off when in reverse. SYNC software updates are now available under the OASIS Tab SYNC selection. If an update is available, refer to WSM Section 415-00 and update the APIM software. For claiming, use causal part 14G371 and applicable labor operations in section 10 of the SLTS manual.
SSM 469062018-01-29. Service bulletin. ENGINE AND ENGINE COOLING; ELECTRICAL SYSTEM. Some 2015-2018 F150/Edge, 2016-2018 MKX and 2017-2018 Fusion, Continental vehicles equipped with a 2.7L engine may experience a malfunction indicator lamp (MIL) and/or wrench lamp with Diagnostic Trouble Codes (DTCs): P0116, P0117, P0118, P0119, P0217, P0330, P1026, and/or P130D. This may be due to a engine coolant temperature (ECT) sensor connector which is not fully seated or damaged wiring between connectors C1064 and C1047 for F150 and C1016 and C1168 for Edge/MKX/Fusion/Continental vehicles. ECT sensors should not be replaced if damaged wiring is found at or near these connectors. If an issue with the wiring is found use causal part 12A699.
SSM 469012018-01-29. Service bulletin. ELECTRICAL SYSTEM; AIR BAGS. Some 2017-2018 Fusion/MKZ vehicles built on or before 27-Oct-2017 may exhibit an illuminated airbag lamp and/or SYNC 911 assist not operational message being displayed. Connect the IDS and check the RCM and APIM for DTCs. If any of the following RCM DTCs U3000, U2100, U2101, U2300, U0455, B0080, B141B, B141C, B0054, B140C, B140D, B0057, B140E, B140F and/or APIM DTC U0452 is stored, then reprogram the RCM to the latest level using IDS or FJDS 107.04 or higher. After reprograming, perform an as-built configuration of the RCM. Make sure you are connected to the internet when entering module programming to obtain the latest updates. For claiming, use causal part 14B321 and applicable labor operations in section 10 of the service labor time standards (SLTS) manual. Calibration files may also be obtained at www.motorcraftservice.com
SSM 469002018-01-29. Service bulletin. POWER TRAIN:AUTOMATIC TRANSMISSION:CONTROL MODULE (TCM/PCM/TECM); ELECTRICAL SYSTEM. Some vehicles may exhibit a no start condition with an illuminated malfunction indicator lamp (MIL) and a DTC P161A after PCM replacement. This may be due to the parameter reset procedure not being properly completed. To clear this DTC, use the Ford Integrated Diagnostic System (IDS) service tool or Ford J2534 Diagnostic Software, select - Toolbox - Body - Security - PATS Functions - Parameter Reset. Follow the on-screen instructions to complete the procedure. This procedure will transfer the existing Key ID information between the modules without the need of having 2 programmed PATS keys present. There is no need to program keys when the PCM is going to be replaced. Additional information can be found in the Workshop Manual (WSM), Section 419-01. Missing or lost keys are not warrantable.
17-22202018-01-29. Service bulletin. ELECTRICAL SYSTEM. Some 2017-2018 Fusion and MKZ vehicles equipped with a 2.0L Gasoline Turbocharged Direct Injection (GTDI) engine and built on or before 29-Sep-2017 may exhibit an illuminated MIL with DTC P04DB (crankcase ventilation system disconnected) in the powertrain control module (PCM) memory. Reprogram the powertrain control module (PCM) using Integrated Diagnostic System (IDS) or Ford J2534 Diagnostic Software (FJDS) release 107.04 or higher. Make sure you are connected to the internet when entering module programming to obtain the latest updates. Calibration files may also be obtained at www.motorcraftservice.com.
SSM 468702017-12-14. Service bulletin. STEERING; ELECTRICAL SYSTEM: INSTRUMENT CLUSTER/PANEL. Some 2017-2018 Fusion SE fleet vehicles equipped with SYNC may have a right side instrument cluster display which is blank and does not respond to inputs from the steering wheel controls. This is a normal condition. For fleet vehicles, equipped with this build combination, the instrument cluster is not configurable and will not respond to inputs from the steering wheel controls. Do not attempt to make repairs for this condition.
tsb17-21922017-12-14. Service bulletin. ELECTRICAL SYSTEM; POWER TRAIN. Some 2017 and 2018 Fusion vehicles equipped with the 2.5L engine and built on or before 18-Aug-2017 without active grille shutters may exhibit a concern of a discharged battery. Battery drain may be a result of key-off load conditions resulting from the powertrain control module (PCM) remaining powered after stop/start button cycling. PCM battery drain may not be reproducible under some circumstances, especially after a battery has been discharged or if the battery has been disconnected. Follow the Service Procedure steps to correct the condition.
SSM 468342017-10-21. Service bulletin. ELECTRICAL SYSTEM:SOFTWARE. Some 2016-2017 Ford and Lincoln vehicles with SYNC 3 may exhibit an intermittent blue or black screen. Check for SYNC software update under the OASIS Tab SYNC selection. If update is available refer to WSM, Section 415-00 and update APIM software. After Installation Complete pop-up appears, remove USB flash drive and install into IDS tool to update Ford database. Perform a complete ignition cycle by turning the key off for 5 minutes which is critical for a successful installation. If no updates are available or a blue or black screen is present after an update refer to WSM, Section 415-00 for diagnosis or SYNC 3 intermittent blank screen GSB for tips. For claiming, use causal part 14G371 and applicable labor operations in section 10 of the SLTS manual.
SSM 467022017-08-25. Service bulletin. ELECTRICAL SYSTEM:SOFTWARE. Some 2016-2017 Ford/Lincoln vehicles SYNC 3 may exhibit an intermittent blank screen. Check for SYNC software update under the OASIS Tab SYNC selection. If update is available refer to WSM, Section 415-00 and update APIM software. During the update process the SYNC status bar shows Updating System Software for approximately 30 minutes. After Installation Complete pop-up appears, remove USB flash drive and install into IDS tool to update Ford database. Perform a complete ignition cycle by turning the key off for 5 minutes which is critical for a successful installation. If no updates are available or blank screen is present after an update refer to WSM, Section 415-00 for diagnosis or SYNC 3 intermittent blank screen GSB for tips. For claiming, use causal part 14G371 and applicable labor operations in section 10 of the SLTS manual.
SSM 466882017-08-25. Service bulletin. ELECTRICAL SYSTEM:12V/24V/48V BATTERY; ELECTRICAL SYSTEM. Some 2017 MKZ and Fusion vehicles equipped with memory seats and built on or before 3-Jun-2016 may exhibit a discharged battery or a battery drain condition. Before performing normal diagnostics, reprogram the driver door module (DDM) to the latest calibration using the Integrated Diagnostic System (IDS) version 106.01 or higher. Make sure you are connected to the internet when entering module programming to obtain the latest updates. Calibration files may also be obtained at www.motorcraftservice.com. Use causal part 14B291 and applicable labor operations from Section 10 of the service labor time standards (SLTS)manual.
SSM 466862017-08-25. Service bulletin. ELECTRICAL SYSTEM; STRUCTURE:BODY:DOOR. Some 2017 Fusion and MKZ vehicles built on or before 18-Feb-2017 and Continental vehicles may exhibit front windows that fail to open or close completely, bounce back, and/or have a complete loss of the one-touch feature. Reprogram the driver door module (DDM) and/or the passenger door module (PDM) to the latest calibration using IDS version 106.02 or higher. Make sure you are connected to the internet when entering module programming to obtain the latest updates. Calibration files may also be obtained at www.motorcraftservice.com. After programming perform the IDS power window initialization procedure. Access to this IDS learn procedure is available under Toolbox/Body/Power Window Initialization. For claiming, use causal part 14B291 and applicable labor operations in section 10 of the service labor time standards (SLTS) manual.
16B35-S12017-08-01. Service bulletin. POWER TRAIN:AUTOMATIC TRANSMISSION:CONTROL MODULE (TCM/PCM/TECM); ELECTRICAL SYSTEM:SOFTWARE. Certain 2016-2017 Model Year C-MAX and Fusion Energi Vehicles - Reprogram Powertrain Control Module
SSM 460732017-08-01. Service bulletin. EQUIPMENT:ELECTRICAL; ELECTRICAL SYSTEM. Some 2016-2017 Escape, MKC, Fiesta, F150, Expedition, Navigator, Mustang, Transit, Focus, C-Max, MKX, Taurus, MKS, Flex, MKT, and Edge and 2017 Explorer, Fusion, MKZ, Super Duty, Transit Connect and Continental vehicles equipped with SYNC 3 might exhibit a blank screen or other various SYNC symptoms only when the vehicle is in Transport mode. Engineering is aware of this possibility and it is considered normal due to the power saving features enabled while in transportation mode. It is beneficial to extended battery life to keep the vehicle in Transport Mode until the vehicle is prepped for sale. If the vehicle should exhibit a blank screen or other SYNC symptoms after it has been taken out of Transport mode, refer to Workshop Manual, Section 415-00 for normal diagnosis. The SYNC version can be confirmed via OASIS.

The summaries are NHTSA's. Each bulletin's page links NHTSA's copy of the manufacturer's document.