WenmarOpen by Wenmar Pro

Service bulletins for the 2018 Ford Focus

A bulletin is a manufacturer's communication to its dealers, as NHTSA indexes it. The summary is NHTSA's. The document is the manufacturer's: read it at NHTSA. A bulletin is not a recall, and listing a model year does not mean every vehicle of it is concerned.

107 on file from NHTSA, as of 2026-10-19.

By type

By component

By trouble code

By topic

Only bulletins with component: Electrical system are shown. Show all

Bulletins, newest first
SSM 480532019-07-08. Service bulletin. ELECTRICAL SYSTEM. Some 2016-2019 Ford and Lincoln vehicles equipped with SYNC 3 not at the latest software level may exhibit Various Performance Related concerns such as Display Operation, Navigation, Voice Recognition, Phone Pairing, Applink, Travel Link, Slow System Response, etc. Check for SYNC software update under the OASIS Tab SYNC selection. If an update is available refer to WSM,Section 415-00 and update the APIM software. After Installation, complete pop-up appears, remove USB flash drive and install into IDS tool to update Ford database. Perform a complete ignition cycle by turning the key off for 5 minutes which is critical for a successful installation. If no updates are available or a blue or black screen is present after an update refer to WSM, Section 415-00 for diagnosis or SYNC 3 intermittent blank screen GSB for tips. For claiming, use causal part 14G371 and applicable labor operations in section 10 of the SLTS manual. Section
SSM 479272019-05-07. Service bulletin. ELECTRICAL SYSTEM; EQUIPMENT:ELECTRICAL:RADIO/TAPE DECK/CD ETC.. SSM 47927 - 2017 F-Super Duty, 2016-2017 Expedition/Navigator, 2016-2018 Focus/Fiesta - Radio Reverting To AM Or FM After Vehicle Shut Down and Start Up Some 2017 F-Super Duty, 2016-2017 Expedition/Navigator and 2016-2018 Focus/Fiesta vehicles may exhibit a concern where the radio reverts to an AM or FM station after shutting the vehicle off, leaving it off for at least 20 minutes, and then starting it back up. Do not perform any repairs for this concern. If a vehicle exhibits this concern, please use the Report a Vehicle Concern link at the bottom of the OASIS tab and submit a report. Engineering is investigating. Monitor OASIS for updates.
SSM 478502019-05-07. Service bulletin. ELECTRICAL SYSTEM; EQUIPMENT:APPLIANCE:AIR CONDITIONER. Some 2013-2019 vehicles equipped with a EVDC air conditioning (A/C) compressor may exhibit poor A/C performance/improper climate function and/or a diagnostic trouble code (DTC) P06A0 in the powertrain control module (PCM). To support the proper diagnosis of this compressor, the EVDC control valve tester has been developed and is available from Rotunda (339-EVDC100). A tester has been provided to each U.S. dealership free of charge with shipments completed 19-Apr-2019 (reference EFC07013 on FMCDealer.com). This tester will help reduce the potential for misdiagnosis and unnecessary compressor replacement. Make sure that this tester is used for warranty repairs and document the test results in the Technician Comments field. Refer to the Rotunda catalog for a video and user manual which provide detailed operating instructions.
SSM 478242019-04-08. Service bulletin. ELECTRICAL SYSTEM. Some 2015-2017 vehicles may experience a no crank concern due to a security access key table error. When attempting to program keys or perform a parameter reset, the procedure may fail and the Integrated Diagnostic System (IDS) scan tool may display an error 232: Key Table Not Allocated. If this error message is encountered, the Body Control Module (BCM) is internally faulted and requires replacement. For claiming, use causal part 15604 and applicable labor operations in section 10 of the Service Labor Times Standards (SLTS) manual.
SSM 478752019-04-03. Service bulletin. ELECTRICAL SYSTEM. Some 2014-2019 Escape, 2014-2018 C-MAX, Focus, and Transit Connect vehicles not equipped with an auto start/stop system may exhibit an inability to program and/or no electrical power after installation of a service part body control module (BCM). Inspect the BCM for the presence of fuse F88. If fuse 88 is missing, install a 25 amp fuse and then re-evaluate the concern. If fuse 88 is installed in a vehicle with an auto start/stop system, the vehicle may exhibit concerns where the radio is turning off during an auto start/stop event and the instrument panel cluster (IPC) back lighting slowly goes dim during auto start/stop events.
SSM 478242019-04-01. Service bulletin. ELECTRICAL SYSTEM. Some 2015-2017 vehicles may experience a no crank concern due to a security access key table error. When attempting to program keys or perform a parameter reset, the procedure may fail and the Integrated Diagnostic System (IDS) scan tool may display an error 232: Key Table Not Allocated. If this error message is encountered, the Body Control Module (BCM) is internally faulted and requires replacement. For claiming, use causal part 15604 and applicable labor operations in section 10 of the Service Labor Times Standards (SLTS) manual.
SSM 477482019-03-04. Service bulletin. ELECTRICAL SYSTEM. Some 2016-2019 Escape and 2016-2018 Focus/C-Max vehicles may exhibit a customer perceived concern of a FDIM screen flicker during transitions between day/night mode and/or during auto headlamp on/off. The FDIM utilizes a ramp up and ramp down strategy of controlling the back lighting when the display setting is in auto dimming mode. This is a normal condition that does not affect the function or durability of the FDIM. Auto dimming mode can be turned off to minimize the ramp up and ramp down lighting strategy. To turn off the auto dimming mode feature in the FDIM display: select> FDIM settings> Display settings> Auto Dim selection. Do not confuse the auto dimming mode selection with the selection for auto day/night operation. Turning off auto dimming mode only effects the back lighting strategy and does not affect any other function or FDIM reliability.
SSM 477112019-03-04. Service bulletin. ELECTRICAL SYSTEM. Some 2016-2019 Ford and Lincoln vehicles equipped with SYNC 3 and a 6, 8 or 10 inch screen may show a pop-up message every key cycle that states 'SYNC can check for updates when connected to a WiFi network'. To remove the inconvenience of the pop-up the customer can either connect to a trusted WiFi network to complete the setup process or turn off WiFi in the WiFi settings located under the Settings menu. Adjusting the setting for the customer is not a warrantable defect.
SSM 477032019-03-04. Service bulletin. ELECTRICAL SYSTEM; EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL. Some 2014-2019 Escape, 2014-2018 C-MAX,Focus, and Transit Connect vehicles may exhibit a concern of not able to program and/or no electrical power after installation of a service part Body Control Module(BCM). Inspect the BCM for the presence of fuse F88. If the fuse is missing, install the correct size replacement fuse as outlined in the Wiring Manual and then re-evaluate the concern.
TSB 18-23732019-03-04. Service bulletin. ELECTRICAL SYSTEM. Some 2012-2018 Focus Electric, 2013-2017 C-Max Energi, and 2013-2019 Fusion Energi plug-in hybrid electric vehicles (PHEV) may exhibit the high voltage (HV) battery failing to charge while connected to the second Generation 120-volt electric vehicle service equipment (EVSE) charge cord. Follow the Service Procedure steps to correct the condition.
SSM 475382018-12-03. Service bulletin. ELECTRICAL SYSTEM. Some 2016-2018 Ford and Lincoln vehicles equipped with SYNC 3 may exhibit the Android Auto Preference menu selection is not present after an update to version 3.0 software. In prior versions of SYNC 3 software this menu was present, however in version 3.0 software the Android Auto Preference menu will only show up once an Android Phone has been initially connected to SYNC. This an operating characteristic of the Android Auto application after the SYNC 3.0 update and no repairs should be attempted.
SSM 475282018-12-03. Service bulletin. ELECTRICAL SYSTEM. Some 2012-2018 Focus BEV vehicles may exhibit DTC U0130 in the battery electric control module (BECM) after replacement of the high voltage (HV) battery pack. In order to correct the condition, perform a programmable module installation (PMI) using the appropriate Ford scan tool. This action will initiate a coordinated flash of powertrain control module (PCM) and transmission control module (TCM) for HV battery compatibility. The use of a previous session may also cause DTC U1030 to be present in the BECM. For additional information refer to 2015 or newer Workshop Manual (WSM), Section 414-03A
SSM 474442018-09-24. Service bulletin. ELECTRICAL SYSTEM. Some 2016-2018 Ford and Lincoln vehicles equipped with SYNC 3 not at the latest software level may exhibit Various Performance Related concerns such as Display Operation, Navigation, Voice Recognition, Phone Pairing, Applink, Travel Link, Slow System Response, etc. Check for SYNC software update under the OASIS Tab SYNC selection. If an update is available refer to WSM, Section 415-00 and update the APIM software. After Installation, complete pop-up appears, remove USB flash drive and install into IDS tool to update Ford database. Perform a complete ignition cycle by turning the key off for 5 minutes which is critical for a successful installation. If no updates are available or a blue or black screen is present after an update refer to WSM, Section 415-00 for diagnosis or SYNC 3 intermittent blank screen GSB for tips. For claiming, use causal part 14G371 and applicable labor operations in section 10 of the SLTS manual.
SSM 473972018-09-10. Service bulletin. ENGINE; ELECTRICAL SYSTEM. Some 2016-2018 Escape/Focus/Transit Connect vehicles equipped with a remote start system may exhibit an immediate engine shut off with or without diagnostic trouble code (DTC) P1594 stored in the BCM after using the remote start function to start the engine. If using FordPass, the app will indicate that the vehicle started successfully, but the engine may not have started or may start and then immediately shut off. Reprogram the BCM using the appropriate Ford scan tool or equivalent release 110.02 or higher. Make sure you are connected to the internet when entering module programming to obtain the latest updates. For claiming, use causal part 14A068 and applicable labor operations in Section 10 of the Service Labor Time Standards (SLTS) Manual.
SSM 473802018-07-23. Service bulletin. EQUIPMENT; EQUIPMENT ADAPTIVE/MOBILITY; ELECTRICAL SYSTEM. Some 2016-2018 Ford and Lincoln vehicles with SYNC 3 may exhibit an intermittent blue or black screen. Check for SYNC software update under the OASIS Tab SYNC selection. If update is available refer to WSM, Section 415-00 and update APIM software. After Installation Complete pop-up appears, remove USB flash drive and install into IDS tool to update Ford database. Perform a complete ignition cycle by turning the key off for 5 minutes which is critical for a successful installation. If no updates are available or a blue or black screen is present after an update refer to WSM, Section 415-00 for diagnosis or SYNC 3 intermittent blank screen GSB for tips. For claiming, use causal part 14G371 and applicable labor operations in section 10 of the SLTS manual.
SSM 473792018-07-23. Service bulletin. ELECTRICAL SYSTEM; EQUIPMENT. Various 2016-2018 vehicles with SYNC 3 may experience a touch screen that does not respond to any input. Using the Professional Technician Society (PTS) website > OASIS tab > SYNC version, verify the vehicle SYNC software version. If the vehicle is at version 2.2 please update the module to the latest software level. After the software is updated make sure you shut the vehicle off, open the door for 2 minutes, then turn the key back on before testing the touch screen. If the software is at a later version than 2.2, proceed with normal diagnostics in Workshop Manual (WSM), Section 415-00. For claiming, use causal part 14G371 and applicable labor operations in section 10 of the Service Labor Times Standards (SLTS) manual.
SSM 470072018-06-11. Service bulletin. WHEELS; ELECTRICAL SYSTEM:12V/24V/48V BATTERY; TIRES. The EV Range after fully charging a Focus Electric, C-MAX/Fusion Energi may vary after each charge event. The window sticker indicates 0-20 mile range for C-MAX Energi, 0-21 mile range for Fusion Energi. Variation of EV range may not indicate a battery or charging concern. EV range is similar to the DTE display on gasoline vehicles, EV range will vary with driving/operating conditions. Conditions include: extreme outside temperatures, terrain, driving style, city or highway driving, tire pressure, and use of accessories. If the customer replaces the low roll resistance tires with a more aggressive tread the range will suffer. Using the cabin heater and A/C, which are electric, will also decrease EV range. To temporarily remove the impact of driving/climate history , reset the Driving History/Lifetime Summary by using the Settings menu on the left side of the instrument cluster, under Display
SSM 470042018-06-11. Service bulletin. ELECTRICAL SYSTEM: INSTRUMENT CLUSTER/PANEL; EQUIPMENT:APPLIANCE:AIR CONDITIONER. Some 2016-2018 Model Year Focus RS may exhibit inaccurate Outside Air Temperature(OAT) readings with intermittent Air Conditioning(A/C) function. Instrument cluster will display 0 degrees F(-18 degrees C) until the vehicle is driven above 20-30 mph for minimum of 1 minute. Concern can occur when engine is running(Key On Engine Running-KOER) and ignition is cycled Off and On again within 1 second. Do not replace Powertrain Control Module(PCM) or ambient air temperature sensor for concern. Sensor is contained within the right hand outside mirror, and is not serviceable separately . Engineering is currently investigating. To assist with the investigation use Report A Vehicle Concern link at the bottom of the Oasis report and submit a Global Concern Report (GCR). Continue to monitor OASIS for future updates.
SSM 470072018-05-29. Service bulletin. ELECTRICAL SYSTEM. The EV Range after fully charging a Focus Electric, C-MAX/Fusion Energi may vary after each charge event. The window sticker indicates 0-20 mile range for C-MAX Energi, 0-21 mile range for Fusion Energi. Variation of EV range may not indicate a battery or charging concern. EV range is similar to the DTE display on gasoline vehicles, EV range will vary with driving/operating conditions. Conditions include: extreme outside temperatures, terrain, driving style, city or highway driving, tire pressure, and use of accessories. If the customer replaces the low roll resistance tires with a more aggressive tread the range will suffer. Using the cabin heater and A/C, which are electric, will also decrease EV range. To temporarily remove the impact of driving/climate history , reset the Driving History/Lifetime Summary by using the Settings menu on the left side of the instrument cluster, under Display
SSM 471302018-05-21. Service bulletin. ELECTRICAL SYSTEM: INSTRUMENT CLUSTER/PANEL. Some 2012-2018 Focus Electric, 2013-2017 C-Max Energi, and 2013-2018 Fusion Energi plug-in hybrid electric vehicles (PHEV) may exhibit the high voltage (HV) battery failing to charge while connected to the Delphi 120 volt electric vehicle service equipment (EVSE) charge cord. To identify a Delphi EVSE the coupler on the EVSE that connects to the vehicle charge port is solid black. For information on the Delphi EVSE indicator status used for diagnostics, reference High Voltage Battery > Charging the High Voltage Battery in the Owners Guide for a 2018 Fusion Energi. Reference the Convenience Cord Light Emitting Diode (LED) Indicators chart. The Workshop Manual (WSM) is scheduled to be revised at a later date.
SSM 469072018-01-29. Service bulletin. ELECTRICAL SYSTEM; ENGINE AND ENGINE COOLING. Some 2015-2018 Focus ST vehicles may exhibit MIL On with DTC's P0300 and/or P0316 store in Powertrain Control Module(PCM) memory. Vehicle may also exhibit perceived misfire after cold start until Engine Coolant Temperature(ECT) reaches 49 degrees C (120 degrees F) Install (4) new CYFS-12-YEC spark plugs and set plug gap to 1.0mm(0.040). Use ROTUNDA RTTP tool KDT165 or equivalent to gap and adjust the plugs before installing. For Drivability concerns Refer to Powertrain Control/Emissions Diagnosis (PC/ED) manual. Engineering is currently investigating this concern. To assist with the investigation use the Report A Vehicle Concern link at the bottom of the Oasis report and submit a Global Concern Report (GCR). Continue to monitor OASIS for updates.
SSM 469002018-01-29. Service bulletin. POWER TRAIN:AUTOMATIC TRANSMISSION:CONTROL MODULE (TCM/PCM/TECM); ELECTRICAL SYSTEM. Some vehicles may exhibit a no start condition with an illuminated malfunction indicator lamp (MIL) and a DTC P161A after PCM replacement. This may be due to the parameter reset procedure not being properly completed. To clear this DTC, use the Ford Integrated Diagnostic System (IDS) service tool or Ford J2534 Diagnostic Software, select - Toolbox - Body - Security - PATS Functions - Parameter Reset. Follow the on-screen instructions to complete the procedure. This procedure will transfer the existing Key ID information between the modules without the need of having 2 programmed PATS keys present. There is no need to program keys when the PCM is going to be replaced. Additional information can be found in the Workshop Manual (WSM), Section 419-01. Missing or lost keys are not warrantable.

The summaries are NHTSA's. Each bulletin's page links NHTSA's copy of the manufacturer's document.