WenmarOpen by Wenmar Pro

Service bulletins for the 2022 Ford F-600

A bulletin is a manufacturer's communication to its dealers, as NHTSA indexes it. The summary is NHTSA's. The document is the manufacturer's: read it at NHTSA. A bulletin is not a recall, and listing a model year does not mean every vehicle of it is concerned.

51 on file from NHTSA, as of 2026-10-19.

By type

By component

By trouble code

Only bulletins with component: Transmission and driveline are shown. Show all

Bulletins, newest first
TSB 26-2375 v22026-10-13. Service bulletin. UNKNOWN OR OTHER; ELECTRICAL SYSTEM; POWER TRAIN. NOTE: This bulletin has been updated, refer to the change log at the bottom for details. Issue: Some of the vehicles listed in the Model statement above may exhibit all of the following conditions: • Poor shift quality • Illuminated powertrain malfunction (wrench) indicator with DTCs P2704 and P0771 stored in the PCM / TCM . This may be due to a calibration in the TCM and/or wear between the input shaft and the E clutch hub causing theinput shaft O-rings to become damaged resulting in an open E clutch circuit. Action: For vehicles that meet all of the criteria in the Issue and Model statements, follow the Service Procedure toreprogram the PCM / TCM and/or replace the E clutch hub and input shaft O-rings
25N102026-03-05. Other. POWER TRAIN; UNKNOWN OR OTHER. Certain 2017-2025 F-450 – F-600 Super Duty Chassis Cab Upfitted with an Aerial Bucket Frame Rail Crack
TSB 26-20502026-02-17. Service bulletin. POWER TRAIN. This article supersedes TSB 24-2142 to update the Parts List, Service Procedure (Steps 1-2), and increase the labor operation allowances to reprogram the PCM/TCM. Some of the vehicles listed in the Model statement above may exhibit all of the following conditions: Poor shift quality Illuminated powertrain malfunction (wrench) indicator with diagnostic trouble codes (DTC) P2704 and P0771 stored in the PCM/TCM. This may be due to a calibration in the TCM and/or wear between the input shaft and the E clutch hub causing the input shaft O-rings to become damaged resulting in an open E clutch circuit. Additional model information: 6.7L Diesel Engine 2022-2024 F-550 or F-600 F-Super Duty vehicles built on or before 15-May-2024 with over 5,000 miles (8,000km)
TSB 24-22492024-09-02. Service bulletin. POWER TRAIN. This article supersedes TSB 22-2087 to update the Part List. Some 2020-2022 F-Super Duty vehicles equipped with a 10R140 automatic transmission may exhibit harsh reverse to drive engagements without diagnostic trouble codes (DTCs). This may be due to sticking valves in the main control valve body or suspect input shaft seals (F9) and the output shaft seals (F10). To correct the condition, follow the Service Procedure steps to perform the transmission accelerated main control break-in routine for the E and F clutches and if necessary, replace the input shaft seals (F9) and the output shaft seals (F10).
TSB 24-21422024-06-12. Service bulletin. POWER TRAIN. This article supersedes TSB 23-2376 to update the Part List and the Service Procedure. Some 2022-2024 F-550 and F-600 F-Super Duty vehicles equipped with a 10R140 automatic transmission and 6.7L diesel engine may exhibit an illuminated powertrain malfunction (wrench) indicator with diagnostic trouble codes (DTCs) P2704 and P0771 stored in the transmission control module (TCM) with poor shift quality and over 5,000 miles (8,000 km) in service. This may be due to wear between the input shaft and the E clutch hub causing the input shaft O-rings to become damaged resulting in an open E clutch circuit. To correct this condition, follow the Service Procedure to replace the E clutch hub and input shaft O-rings.
SSM 525952024-06-10. Service bulletin. POWER TRAIN. When replacing the E clutch hub (7P211) on 2020-2024 F-Super Duty and 2024-2025 F-650/F-750 vehicles equipped with a 10R140 transmission, a new washer (7482) has been added and must be installed with the new updated E clutch hub. Refer to the Workshop Manual (WSM), Section 307-01B for proper installation of the washer. Refer to the parts catalog for the appropriate part numbers for the E clutch hub and the washer.
SSM 525482024-05-23. Service bulletin. POWER TRAIN. Various vehicles equiped with 10R80/10R80 MHT/10R100/10R140 transmissions may require replacement of the seal kits (7153) when internal repairs are being performed. These kits come with 4 wheel drive (4WD) seals and will no longer include the 2WD seals. When working on a 2WD vehicle, any 2WD seals must be ordered separately. Refer to the parts catalog for the proper 2WD seals required.
SSM 523892024-04-04. Service bulletin. POWER TRAIN:AUTOMATIC TRANSMISSION:CONTROL MODULE (TCM/PCM/TECM); POWER TRAIN:MANUAL TRANSMISSION:CONTROL MODULE (TCM/PCM/TECM). Some 2022-2024 F-Super Duty vehicles equipped with a 6.7L engine may exhibit an illuminated malfunction indicator lamp (MIL) with only diagnostic trouble code (DTC) U3012 stored in the PCM. If no drivability concerns or other DTCs are present, perform normal diagnostics per the Workshop Manual (WSM). If diagnostics lead to the powertrain control module (PCM) or body control module (BCM), the replacement of the PCM and/or the BCM will not resolve this concern. This illuminated MIL with DTC U3012 does not affect vehicle durability and no additional diagnosis or service is required for this condition at this time. Inform customers that they can continue to drive the vehicle and engineering is currently working on a solution for this condition. Monitor OASIS for additional information and schedule service appointments for customers once the repair becomes available.
SSM 523142024-03-20. Service bulletin. POWER TRAIN. During service and repair requiring removal and replacement of a crankshaft bolt and/or crankshaft damper, achieving proper torque of the crankshaft pulley bolt is critical. Incorrect torque may allow the bolt to loosen resulting in the timing gear breaking and engine damage. Replacement of the bolt is critical to the repair and accurately following the installation procedure in the Workshop Manual (WSM) Section, 303-01 is extremely important. The bolt torque procedure can be found in the crankshaft front seal removal and installation procedure or in the engine assembly procedure.
TSB 23-23762024-01-05. Service bulletin. POWER TRAIN:AUTOMATIC TRANSMISSION:CONTROL MODULE (TCM/PCM/TECM); POWER TRAIN. Some 2022 F-550 and F-600 F-Super Duty vehicles equipped with a 10R140 automatic transmission and 6.7L diesel engine may exhibit an illuminated powertrain malfunction (wrench) indicator with diagnostic trouble codes (DTCs) P2704 and P0771 stored in the transmission control module (TCM) with poor shift quality and over 5,000 miles (8,000 km) in service. This may be due to wear between the input shaft and the E clutch hub causing the input shaft O-rings to become damaged resulting in an open E clutch circuit. To correct this condition, follow the Service Procedure to replace the E clutch hub and input shaft O-rings.
SSM 517192023-06-21. Service bulletin. POWER TRAIN; ENGINE AND ENGINE COOLING. Some 2021-2023 F-Super Duty/E-Series vehicles equipped with a 6.2L, 6.8L or 7.3L gasoline engine may exhibit an illuminated malfunction indicator lamp (MIL) with diagnostic trouble code (DTC) P0457 and/or P0455 stored in the powertrain control module (PCM). This may be due to a improper fuel filler cap installation and/or outside contamination on the fuel cap sealing surface. The fuel filler cap requires multiple turns to seal properly and should be clean of any debris on sealing surface. Advise the customer to turn the fuel filler cap clockwise until there is at least one audible click to seal properly. If the DTCs return after the fuel filler cap is cleared of debris and properly seated, refer to Workshop Manual (WSM), Section 303-13 > pinpoint test HX.
SSM 516912023-06-16. Service bulletin. ENGINE AND ENGINE COOLING:EXHAUST SYSTEM; POWER TRAIN. 2011-2023 F-Super Duty and 2016-2024 F-650/F-750 vehicles equipped with a 6.7L engine may exhibit an elevated idle condition. During prolonged idle time, vehicles may experience this elevated idle to reduce unburned hydrocarbons from the SCR. The powertrain control module estimates hydrocarbon levels in the SCR and may increase idle speed to remove them. Idle speed will be increased to 1000 RPM for ambient temperatures near 26°C (80°F) and may increase to 1200 RPM at -40 °C (-40°F). Vehicles may exhibit exhaust smoke and diesel exhaust fluid smell during elevated idle condition. Exhaust smoke and smell condition will not affect reliability or durability of the engine. Power take-off (PTO) use and idle set point control will disable elevated speed. It is required that the operator monitor the vehicle and adhere to any Exhaust Filter warning messages.
SSM 516522023-05-31. Service bulletin. POWER TRAIN; BACK OVER PREVENTION:SOFTWARE. Some 2022 F-Super Duty vehicles equipped with a 6.7L engine, and built on 13-May-2022 and through 05-Aug-2022 at Kentucky Truck Plant or built on 13-Jun-2022 and through 09-Aug-2022 at Ohio Assembly Plant may exhibit an illuminated malfunction indicator lamp (MIL) with various diagnostic trouble codes (DTC) stored in the powertrain control module (PCM). While attempting to perform TSBs 23-2077, 23-2076, and/or 23-2082, vehicles that were produced without a particulate matter sensor will not show a PCM software update available in Ford Diagnosis and Repair System (FDRS). Refer to EFC10061 (MBG-2022-174N in Canada) and monitor OASIS for updates.
SSM 516482023-05-31. Service bulletin. POWER TRAIN; EQUIPMENT. Some 2020-2022 F-Super Duty vehicles equipped with a 6.7L engine may experience a lack of power due to snow packing of the engine air cleaner when operating in extremely snowy conditions. This may also be due to ice forming in the air intake while operating in temperatures below -22°F (-30°C). Diagnostic trouble code (DTC) P1548 may be present in the powertrain control module (PCM). To supplement heavy snow environment pre-filter service kit (service part LC3Z-9K635-AA), a front grill cover (service part NC3Z-19A413-A) is now available for service but is not a warrantable item. It is recommended that the front grill cover be removed at temperatures greater than 10°F (-12°C) and reinstall in subsequent winter seasons in order to maintain optimal vehicle performance.
SSM 516492023-05-23. Service bulletin. POWER TRAIN. Some 2021-2023 F-Super Duty vehicles equipped with a 10R140 transmission may exhibit harsh or delayed engagement/shift concerns. Most concerns may be addressed with the PCM/TCM Transmission Accelerated Main Control Break In Routine. Refer to Workshop Manual, Section 307-01, DTC Chart and/or Diagnosis By Symptom to identify the clutch(s) to be cycled. This routine cycles the shift solenoids and clutch control valves to remove contamination that may be sticking the valves and must be performed along with an adaptive learning drive cycle before attempting internal service. Although this routine was developed for low mileage vehicles, it has proven effective for resolving many shift and engagement symptoms across the life of the vehicle. For claiming, use causal part 7A100 and applicable labor operations in Section 7 of the Service Labor Time Standards Manual.
SSM 516292023-05-16. Service bulletin. EQUIPMENT:ELECTRICAL; POWER TRAIN. Some 2022 F-Super Duty vehicles equipped with a 6.7L engine, and built on 13-May-2022 and through 05-Aug-2022 at Kentucky Truck Plant or built on 13-Jun-2022 and through 09-Aug-2022 at Ohio Assembly Plant may exhibit an illuminated malfunction indicator lamp (MIL) with various diagnostic trouble codes (DTC) stored in the powertrain control module (PCM). While attempting to perform TSBs 23-2077, 23-2076, and/or 23-2082, vehicles that were produced without a particulate matter sensor will not show a PCM software update available in Ford Diagnosis and Repair System (FDRS). Refer to EFC10061 and monitor OASIS for updates.
SSM 507422022-05-14. Service bulletin. POWER TRAIN; ELECTRICAL SYSTEM. Some 2020-2022 F-Super Duty vehicles may exhibit an illuminated malfunction indicator lamp (MIL) with diagnostic trouble code (DTC) P0073 for the ambient air temperature sensor stored in the powertrain control (PCM). When performing pinpoint test BF in Workshop Manual (WSM), Section 413-01, the ambient air temperature sensor/outside air temperature display reset procedure has been added to the Ford Diagnostic Repair System (FDRS) diagnostic scan tool. Depending on how the vehicle is equipped, run the FCIM or HVAC. Reset the Outside Air Temperature Sensor Learned Values application. Clear DTCs and retest after performing the reset procedure.

The summaries are NHTSA's. Each bulletin's page links NHTSA's copy of the manufacturer's document.