WenmarOpen by Wenmar Pro

Service bulletins for the 2022 Ford Explorer

A bulletin is a manufacturer's communication to its dealers, as NHTSA indexes it. The summary is NHTSA's. The document is the manufacturer's: read it at NHTSA. A bulletin is not a recall, and listing a model year does not mean every vehicle of it is concerned.

262 on file from NHTSA, as of 2026-10-19.

By type

By component

By trouble code

Only bulletins with component: Engine are shown. Show all

Bulletins, newest first
TSB 22-23772022-10-31. Service bulletin. ENGINE AND ENGINE COOLING. Some 2020-2022 Explorer/Aviator vehicles equipped with a 3.0L EcoBoost engine may exhibit a ticking/tapping or rattle type noise from the top front cover area of the engine on initial start-up after a cold soak of 6 hours or more that may last for 2-5 seconds. This may be due to a worn variable cam timing (VCT) unit. To correct the condition, follow the Service Procedure to replace the VCT units.
TSB 22-23502022-09-23. Service bulletin. POWER TRAIN; ENGINE AND ENGINE COOLING. Some 2020-2022 Police Interceptor Utility vehicles equipped with a 3.3L Duratec (non-hybrid) engine may exhibit a delayed acceleration response at low vehicle speeds with no DTCs. This may be due to the software in the powertrain control module (PCM). To correct the condition, follow the Service Procedure to reprogram the PCM.
SSM 510742022-09-13. Service bulletin. ENGINE AND ENGINE COOLING. Some 2022 Explorer/Police Interceptor Utility and 2022-2023 Aviator vehicles built on or before 19-Aug-2022 and equipped with 3.0L Ecoboost engines may exhibit an engine coolant leak at the water pump output spigot to the transmission oil cooler inlet hose connection. This may be due to the connection at the water pump outlet to coolant hose. To correct this condition, replace the coolant hose assembly with service part number L1MZ-7G071-A.
SSM 510322022-08-22. Service bulletin. POWER TRAIN:AUTOMATIC TRANSMISSION; ENGINE AND ENGINE COOLING. Some 2020-2022 Explorer/Aviator vehicles may exhibit automatic transmission fluid (ATF) contamination in the engine cooling system due to the transmission cooler. If the cooling system becomes contaminated with ATF, the system must be flushed clear of the contamination after the source of the contamination has been repaired. It is generally not necessary to replace the following components due to ATF contamination in the cooling system: radiator, heater core, de-gas bottle, water pump, auxiliary water pump, coolant control valves, temperature sensors, thermostat, turbocharger, heat exchangers, tubes, gaskets/O-rings/seals (unless removed), or rubber coolant hoses (unless swollen).
SSM 510032022-08-15. Service bulletin. ENGINE AND ENGINE COOLING. Some 2020-2022 Explorer/Police Interceptor Utility vehicles equipped with a 3.3L Duratec engine may exhibit delayed acceleration response under heavy to wide open throttle input after an engine start. This concern occurs only during the first 30 seconds from key on with no diagnostic trouble codes (DTCs) stored in the powertrain control module (PCM). The customer may perceive this as a delayed throttle response or lack of power. This may be due to the software in the PCM. Engineering is releasing updated software to resolve this concern, which is expected to be released in August 2022. Monitor OASIS for updates and schedule service appointments for customers once the repair becomes available.
SSM 507482022-05-14. Service bulletin. ENGINE; ENGINE AND ENGINE COOLING. Some 2020-2022 Explorer/Aviator/Police Interceptor Utility vehicles may exhibit erratic shifting and/or a transmission fluid venting condition. If during the preliminary inspection the transmission fluid is found to be a foamy pink color this may indicate possible cross contamination of engine coolant and transmission fluid due to an internally leaking transmission fluid cooler assembly. When repairing or replacing the transmission assembly for an internally leaking transmission fluid cooler assembly, use causal part 7869 and applicable labor operations in Section 07 of the Service Labor Time Standards (SLTS) Manual.
TSB 22-21352022-04-26. Service bulletin. FUEL SYSTEM, GASOLINE; ENGINE AND ENGINE COOLING. Some 2022 Explorer/Aviator vehicles equipped with a 3.0L EcoBoost engine and built on 25-Jan-2022 and through 10-Mar-2022 may exhibit a buzz/vibration/rattle noise at engine idle or low revolutions per minute (RPM) underneath the vehicle near the left rear door. This may be due to the pressurized fuel delivery line contacting the body or the fuel tank creating a buzz/vibration/rattle noise. To correct the condition, follow the Service Procedure to install foam tape.
SSM 506702022-04-13. Service bulletin. ENGINE AND ENGINE COOLING; ELECTRICAL SYSTEM; POWER TRAIN. Some 2021-2022 Ranger/Bronco vehicles equipped with a 2.3L EcoBoost engine built on or after 14-Dec-2021 and 2022 Explorer vehicles equipped with a 2.3L EcoBoost engine and built on or after 14-Dec-2021, may exhibit a lack of power with an illuminated malfunction indicator lamp (MIL) with diagnostic trouble code (DTC) P25B4 stored in the powertrain control module (PCM). To correct the condition, clear the DTC and road test the vehicle under load until the vehicle reaches operating temperature. If the DTC repeats, the turbocharger will need to be replaced. For claiming use causal part 6K682 and applicable labor times found in Section 09 of the Service Labor Time Standards (SLTS) Manual. If the DTC does not repeat, release the vehicle to the customer.
SSM 506392022-03-29. Service bulletin. EQUIPMENT; ENGINE AND ENGINE COOLING. Some 2020-2022 Explorer/Aviator vehicles equipped with a 3.0L EcoBoost engine may appear to have a low engine oil level if the proper procedures are not followed. Refer to the Owner's Manual, Maintenance, Engine oil check section. When checking the engine oil level after shutting off the engine wait at least 15 minutes prior to checking in order to allow the oil to drain back to the oil pan. The engine oil level can be checked immediately if the engine has not been started. When changing the engine oil the engine needs to be at normal operating temperature and the oil filter removed before draining the oil. Allow the oil pan to drain completely for up to 5 minutes. Check oil level after filling by following the oil level check procedure.
SSM 504832022-02-16. Service bulletin. ENGINE AND ENGINE COOLING. Some 2021-2022 Explorer vehicles equipped with a 2.3L EcoBoost engine and built on 01-Aug-2021 and through 03-Jan-2022 may exhibit a lack of rear heat. This may be due to incorrectly routed coolant hoses in the engine bay. To correct the condition, inspect the 90 degree quick connect coolant hoses attached to the heater outlet hose on the driver's side of the engine. The 90 degree quick connect cooling hose with the shorter abrasion sleeve should be installed on the front port connection of the heater outlet hose, and the 90 degree quick connect cooling hose with the longer abrasion sleeve should be installed on the rear port connection of the heater outlet hose. If the coolant hoses are twisted or installed incorrectly on the heater outlet hose, remove and reinstall them correctly. Refer to Work Shop Manual (WSM), Section 303-03A.
TSB 21-24462022-01-01. Service bulletin. ENGINE AND ENGINE COOLING. Some 2020-2022 Explorer vehicles equipped with a 2.3L EcoBoost engine may exhibit an illuminated malfunction indicator lamp (MIL) with diagnostic trouble code (DTC) P04F0 and/or P144C stored in the powertrain control module (PCM). This may be due to loose or partially connected evaporative emissions (EVAP) vapor lines. To correct the condition, follow the Service Procedure to make sure the EVAP vapor lines are properly connected.
SSM 503062021-12-07. Service bulletin. ENGINE AND ENGINE COOLING. Some 2018-2021 EcoSport, Expedition, Navigator; 2019-2021 Ranger; 2020-2021 Escape, Corsair, Explorer, Transit; 2021 Bronco, Bronco Sport, Edge, Nautilus, F-150, Mustang; 2019-2022 Transit Connect; 2020-2022 Aviator, F-Super Duty; and 2022 Maverick vehicles may exhibit an illuminated malfunction indicator lamp (MIL) with diagnostic trouble codes (DTC) P0496, P0456, P0455, P04F0, and/or P0451. Ford has tested returned EVAP canister purge valves and found them to be fully functional. Prior to replacing the canister purge valve or other EVAP components, perform the following tests using the Ford Diagnosis and Repair System (FDRS) Scan Tool: Full System EVAP Leak Test - FDRS Location: TOOLBOX > PCM > PCM - Evap Emissions System Test and the EVAP Purge Valve Leak Test - FDRS Location: TOOLBOX > PCM > Evap Emission System Toolbox > CPV Check.

The summaries are NHTSA's. Each bulletin's page links NHTSA's copy of the manufacturer's document.