WenmarOpen by Wenmar Pro

Service bulletins for the 2020 Ford Edge

A bulletin is a manufacturer's communication to its dealers, as NHTSA indexes it. The summary is NHTSA's. The document is the manufacturer's: read it at NHTSA. A bulletin is not a recall, and listing a model year does not mean every vehicle of it is concerned.

162 on file from NHTSA, as of 2026-10-19.

By type

By component

By trouble code

Only bulletins with component: Engine are shown. Show all

Bulletins, newest first
TSB 26-21712026-04-22. Service bulletin. ENGINE. This article updates TSB 25-2154. Reasons for update: *Parts List *Service Procedure to replace the output planetary carrier assembly *Added 2023-2024 model year vehicles Some of the vehicles listed in the Model statement above may exhibit all of the following conditions: Shudder condition, most noticeable at speeds below 60 mph (100 km/h) No relevant diagnostic trouble codes (DTC) present Traceable shudder event with IDS/FDRS reading *(Figure 1)* This condition may be perceived/felt as an engine misfire. This may be due to a concern with the output planetary assembly.
SSM 542622025-10-07. Service bulletin. ENGINE. Some 2019-2020 Edge/Nautilus vehicles equipped with a 2.7L EcoBoost, 2020 Aviator vehicles equipped with a 3.0L EcoBoost or 3.0L plug-in hybrid electric vehicle (PHEV) engine, 2020 Explorer vehicles equipped with a 3.0L EcoBoost, and 2020 F-150 vehicles equipped with a 2.7L EcoBoost engine may exhibit a ticking/tapping or rattle type noise from the top front cover area of the engine. This noise may occur on initial start-up after a cold soak of 6 hours or more that may last for 2-5 seconds. This may be due to an internal component of the variable cam timing (VCT) unit. If diagnostics lead to the VCTs as the source of the noise, refer to the 2024 F-150 Workshop Manual (WSM), Section 303-00 > Diagnosis and Testing > Engine > Pinpoint Test F. Pinpoint test F has been updated to include additional steps along with a video on how to identify the single affected VCT unit that requires replacement.
SSM 537642025-05-21. Service bulletin. POWER TRAIN; ENGINE. Some 2020 Continental, 2020-2024 Edge/Nautilus, 2020-2025 Explorer/Aviator/Escape/Corsair/F-150/F-Super Duty/Ranger/Transit/E-Series, 2021-2025 Bronco, and 2022-2025 Maverick vehicles may require an engine cooling system flush to be performed for various concerns. Workshop Manual (WSM), Section 303-03 has been updated to eliminate the need to remove and install the radiator assembly to perform a radiator flush.
SSM 523352024-03-20. Service bulletin. ENGINE AND ENGINE COOLING. For 2015-2024 Ford and Lincoln vehicles equipped with turbocharged engines and customer concern of an engine oil leak, refer to Workshop Manual (WSM), Section 303-00 for oil leak inspection and testing methods. Ford has evaluated turbochargers replaced for oil leak symptoms and although oil may collect on the external surface of a turbocharger, it is extremely rare for a turbocharger assembly to be the root cause of the oil leak. Careful inspection of the turbocharger oil feed and drain tubes should be performed along with the recommended WSM procedures as needed. Warranty claims for turbocharger replacement going forward will be assessed.
TSB 23-23562024-03-07. Service bulletin. ENGINE AND ENGINE COOLING. This TSB supersedes TSB 23-2049 to update the parts list. Some 2019-2023 Edge/Nautilus vehicles equipped with a 2.7L EcoBoost engine may exhibit a ticking/tapping or rattle type noise from the top front cover area of the engine on initial start-up after a cold soak of 6 hours or more that may last for 2-5 seconds. This may be due to stuck internal components of the variable cam timing (VCT) unit. To correct the condition, follow the Service Procedure to replace the VCT units.
SSM 516652023-05-29. Service bulletin. ENGINE AND ENGINE COOLING. Some 2021-2023 Ford and Lincoln vehicles equipped with a 2.7L or 3.0L engine may exhibit an upper engine thump/knock noise coming from the left cylinder head. This condition is most noticeable at idle and may lessen at higher engine speed or while driving. This condition does not affect vehicle durability and will not get worse over time. Use a stethoscope or chassis ears and listen just behind the left cylinder head intake VCT solenoid on the cam cover to determine if the thump/knock noise is coming from the cylinder head/camshaft. The left cylinder head and the camshaft roller followers are available as service parts.
TSB 23-20492023-04-04. Service bulletin. ENGINE AND ENGINE COOLING. Some 2019-2023 Edge/Nautilus vehicles equipped with a 2.7L EcoBoost engine may exhibit a ticking/tapping or rattle type noise from the top front cover area of the engine on initial start-up after a cold soak of 6 hours or more that may last for 2-5 seconds. This may be due to stuck internal components of the variable cam timing (VCT) unit. To correct the condition, follow the Service Procedure to replace the VCT units.
SSM 513852023-03-04. Service bulletin. ENGINE AND ENGINE COOLING. Some 2019-2023 Edge/Nautilus vehicles equipped with a 2.0L engine may exhibit a repeat block heater failure. This may be caused by air in the engine cooling system. The WSM replacement procedure has been updated to include the Engine Cooling System Draining, Vacuum Filling and Bleeding procedure found in Section 303-03A Engine Cooling - 2.0L EcoBoost (184kW/250PS) MI4, General Procedures as the final step. The block heater should not be tested unless all the air has been removed from the engine cooling system following this procedure.
TSB 22-23762022-10-31. Service bulletin. ENGINE AND ENGINE COOLING. Some 2019-2022 Edge/Nautilus vehicles equipped with a 2.7L EcoBoost engine may exhibit a ticking/tapping or rattle type noise from the top front cover area of the engine on initial start-up after a cold soak of 6 hours or more that may last for 2-5 seconds. This may be due to stuck internal components of the variable cam timing (VCT) unit. To correct the condition, follow the Service Procedure to replace the VCT units.
SSM 504852022-02-16. Service bulletin. ELECTRICAL SYSTEM; ENGINE AND ENGINE COOLING. Some 2019-2022 Edge/Nautilus, 2020-2022 Escape/Corsair, and 2021-2022 Bronco Sport vehicles equipped with a 2.0L EcoBoost or 2.3L EcoBoost may exhibit a lack of power with an illuminated malfunction indicator lamp (MIL) with diagnostic trouble codes (DTC) P02AB, P0243, P0299, P25B3, P25B4, P2AB7, P2AB8 and/or P2AB9. This may be due to an inoperative wastegate actuator, missing wastegate actuator e-clip or non-visible damage to the actuator rod. If the diagnostic procedures lead to replacement of the turbocharger assembly, note that a lower level service component has been released K2GZ-9G488-B for Edge/Nautilus/Escape/Corsair/Bronco Sport for service to replace the actuator, actuator rod and both e-clips instead of a complete turbocharger assembly. When replacing the wastegate actuator, it is required to replace all parts included in the service kit.
SSM 502302021-11-02. Service bulletin. ELECTRICAL SYSTEM; ENGINE AND ENGINE COOLING. Some 2019-2020 Edge/Nautilus vehicles equipped with 2.0L EcoBoost engine and built on or before 14-Oct-2020 may exhibit an illuminated malfunction indicator lamp (MIL) with diagnostic trouble codes (DTCs) P0137, P0141 and/or P2096. This may be due to an exhaust gas oxygen sensor seal. To correct the condition, install an updated oxygen sensor, part number K2GZ-9G444-D. Refer to Workshop Manual (WSM), Section 303-14A. For claiming, use casual part 9G444 and the applicable labor operations of Section 10 of the Service Labor Time Standards (SLTS) Manual.
SSM 501712021-10-29. Service bulletin. ENGINE AND ENGINE COOLING; ENGINE AND ENGINE COOLING:ENGINE:HARD PARTS INTERNAL/MECHANICAL. Some 2019-2021 Edge/Nautilus/Ranger, 2020-2021 Escape/Corsair/Explorer, and 2021 Bronco Sport vehicles equipped with a 2.0L/2.3L EcoBoost may exhibit a lack of power with an illuminated malfunction indicator lamp (MIL) with diagnostic trouble codes (DTC) P02AB, P0243, P0299, P1464, P25B3, P25B4, P2AB7, P2AB8 and/or P2AB9. This may be due to an inoperative wastegate actuator, missing wastegate actuator e-clip or non-visible damage to the actuator rod. A lower level service component has been released, K2GZ-9G488-B for Edge/Nautilus/Escape/Corsair/Bronco Sport vehicles and LB5Z-9G488-B for Explorer/Ranger vehicles, for service to replace the actuator, actuator rod and both e-clips. When replacing the wastegate actuator, it is important to replace all parts in the service kit. Turbocharger replacement is not necessary to correct the condition.
SSM 499242021-08-02. Service bulletin. ENGINE AND ENGINE COOLING; FUEL SYSTEM, GASOLINE:DELIVERY:FUEL PUMP. Some 2019 MKC, 2019-2021 Edge/Nautilus/Escape/Ranger/Explorer, 2020-2021 Corsair, and 2021 Bronco Sport vehicles equipped with 2.0L and 2.3L EcoBoost engines may exhibit a light to moderate ticking type noise at idle (600-700 RPM). The noise is usually more prominent in the area of the high-pressure fuel pump, located on the top of the engine just behind the number 4 ignition coil. This noise is not detrimental to engine function and has no short or long-term effects on engine durability. This an operating characteristic of these engines and no repairs should be attempted.
SSM 498212021-06-01. Service bulletin. POWER TRAIN:AUTOMATIC TRANSMISSION; ENGINE AND ENGINE COOLING. Some 2015-2021 Ford and Lincoln vehicles may exhibit an illuminated MIL with diagnostic trouble codes (DTC) P0011, P0012, P0014, P0015, P0016, P0017, P0018, P0019, P0021, P0022, P0024 and/or P0025. This may be due to small debris causing the VCT solenoid to stick. Before attempting any component diagnosis or replacement of the VCT solenoid, refer to Powertrain Control and Emissions Diagnosis (PC/ED) pinpoint test HK11 to cycle the affected VCT solenoid 10 times to attempt to clear the debris. For claiming, use causal part 6M280 and applicable labor operations in Section 10 of the Service Labor Time Standards (SLTS) Manual.
SSM 493282020-12-04. Service bulletin. ENGINE AND ENGINE COOLING; FUEL SYSTEM, OTHER:DELIVERY:FUEL PUMP; EQUIPMENT. Some 2019 MKC, 2019-2020 Edge/Nautilus/Escape/Ranger, 2020 Corsair, 2019-2021 Explorer vehicles equipped with 2.0L and 2.3L EcoBoost engines may exhibit a light to moderate ticking type noise at idle (600-700 RPM). The noise is usually more prominent in the area of the high-pressure fuel pump, located on the top of the engine just behind the number 4 ignition coil. This noise is not detrimental to engine function and has no short or long-term effects on engine durability. This an operating characteristic of these engines and no repairs should be attempted.
SSM 492102020-10-06. Service bulletin. ENGINE AND ENGINE COOLING. Some 2009-2020 Ford and Lincoln vehicles equipped with turbochargers may exhibit an oil leak from the turbocharger oil supply or return tubes, O-rings or 6.7L pedestal gasket. Although oil may collect on the turbocharger, it is very rare for a turbocharger to leak oil. To isolate the source of the leak, refer to Workshop Manual (WSM), Section 303-00 General Information > Diagnosis and Testing > Engine > Engine Oil Leaks - Fluorescent Oil Additive Method procedure. When an oil leak is present at a turbocharger oil supply or drain tube, remove the affected oil tube and inspect for damage, and replace the O-ring seals, pedestal gasket or oil tube as required. Refer to WSM, Section 303-04. For claiming, use the affected oil tube or pedestal gasket as the causal part and applicable labor operations in Sections 6 and 9 of the Service Labor Time Standards (SLTS) Manual.
SSM 490852020-09-04. Service bulletin. ELECTRICAL SYSTEM; EQUIPMENT; ENGINE. Some 2020 Ford and Lincoln vehicles equipped with a TCU may exhibit incomplete user authorization, no authorization pop-up on the SYNC infotainment system, vehicle connectivity concerns, vehicle location disabled message and/or various FordPass/LincolnWay App command/control concerns. To correct these conditions, ensure that customer connectivity settings (CCS) are turned on in the SYNC system. If the concerns persist after CCS is turned on, turn CCS OFF, perform an ignition cycle, and turn CCS settings back on. After any CCS changes, force-close and relaunch the FordPass/ LincolnWay app on the customers phone. Once CCS is turned on, program the TCU to the latest IDS/FDRS version level. If the concern is still present, follow normal diagnostics in Workshop Manual (WSM), Section 415-00. Refer to PTS OASIS home page for TCU version identification. For claiming, use causal part 14G229.
SSM 491222020-09-02. Service bulletin. ENGINE AND ENGINE COOLING:ENGINE:OIL/LUBRICATION; EQUIPMENT. Some 2015-2020 F-150, 2016-2018 MKX, 2019-2020 Nautilus, 2015-2020 Edge, 2017-2019 Fusion, 2017-2020 MKZ And 2017-2020 Continental vehicles equipped with a 2.7L/3.0L EcoBoost engine may appear to have a low engine oil level if the proper procedures are not followed. Refer to the Owner's Manual > Maintenance > Engine oil check section. When checking the engine oil level after shutting off the engine wait at least 15 minutes prior to checking in order to allow the oil to drain back to the oil pan. The engine oil level can be checked immediately if the engine has not been started. When changing the engine oil the engine needs to be at normal operating temperature and the oil filter removed before draining the oil. Allow the oil pan to drain completely for up to 5 minutes. Check oil level after filling by following the oil level check procedure.
TSB 20-22342020-08-06. Service bulletin. ENGINE AND ENGINE COOLING. Some 2019-2020 Edge/Nautilus vehicles equipped with a 2.0L EcoBoost engine may exhibit an illuminated malfunction indicator lamp (MIL) with diagnostic trouble codes (DTCs) P0128, P0217, P044C, P1026, P1285, P1299, P139A and/or P2457 stored in the powertrain control module (PCM). The vehicle may also exhibit low coolant level, white smoke from the tailpipe, an over temperature warning in the instrument panel cluster (IPC), and/or an external coolant leak. This may be due to the exhaust gas recirculation (EGR) cooler and/or settings in the PCM software. To resolve the condition, inspect the EGR cooler and/or update the PCM software.
SSM 489912020-08-04. Service bulletin. ENGINE AND ENGINE COOLING. Some 2015-2020 F150/Edge/Fusion, 2016-2018 MKX, 2019-2020 Nautilus, and 2017-2020 Continental vehicles equipped with 2.7L EcoBoost engines may exhibit an illuminated malfunction indicator lamp (MIL) and/or Engine Coolant Over Temperature warning with diagnostic trouble codes (DTCs) P0116, P0117, P0118, P0119, P0128, P0217, P0330, P1026, P1299, and/or P130D. This may be due to the engine coolant temperature (ECT) sensor or knock sensor wiring harness. To correct the condition, replace the 12A648 ECT sensor and 12A699 knock sensor. Do not disconnect the ECT sensor from the knock sensor harness in case parts are called back for analysis. For claiming, use causal part 12A699 and applicable labor operations in Section 10 of the Service Labor Time Standards (SLTS) Manual.
SSM 483452019-12-05. Service bulletin. ENGINE AND ENGINE COOLING. Some 2019-2020 Edge/Escape/Nautilus/Corsair vehicles equipped with 2.0L EcoBoost engines may exhibit low coolant, white smoke from the tailpipe, an over temperature warning in the instrument panel cluster (IPC), external coolant leaking, and/or illuminated MIL with DTCs P0217, P0401, P1026, P1285, P1299, P2196 or P2467 stored in the PCM. This may be due to an EGR Cooler that is leaking coolant into the engine intake and exhaust system. The EGR cooler should be inspected first to detect the presence of any internal leaks by a visual inspection and a pressure test as defined in the Workshop Manual (WSM). If any coolant is found leaking from the coolant chamber into the exhaust chamber, replace the EGR cooler. If no issues are detected with the EGR cooler, continue repair diagnosis using standard diagnostic procedures as defined in the WSM.

The summaries are NHTSA's. Each bulletin's page links NHTSA's copy of the manufacturer's document.