WenmarOpen by Wenmar Pro

Service bulletins for the 2015 Ford Edge

A bulletin is a manufacturer's communication to its dealers, as NHTSA indexes it. The summary is NHTSA's. The document is the manufacturer's: read it at NHTSA. A bulletin is not a recall, and listing a model year does not mean every vehicle of it is concerned.

182 on file from NHTSA, as of 2026-10-19.

By type

By component

By trouble code

By topic

Only bulletins with component: Engine are shown. Show all

Bulletins, newest first
TSB 18-22552018-09-24. Service bulletin. ENGINE. Some 2013-2018 Escape vehicles equipped with 1.5L/1.6L/2.0L EcoBoost, 2013-2018 Fusion vehicles equipped with 2.0L/2.7L EcoBoost, 2013-2018 MKZ vehicles equipped with 2.0L EcoBoost, 2017-18 MKZ vehicles equipped with 3.0L EcoBoost, 2015-2018 MKC vehicles equipped with 2.0L/2.3L EcoBoost, 2015-2018 Edge vehicles equipped with 2.0L/2.7L EcoBoost, 2016-2018 MKX vehicles equipped with 2.0L and 2.7L EcoBoost, 2016-2018 Explorer vehicles equipped with 2.3L EcoBoost, 2017-2018 Continental vehicles equipped with 2.7L/3.0L EcoBoost and 2016-2018 Focus RS equipped with 2.3L EcoBoost may exhibit a dark black fluid leak from the right side transfer case intermediate shaft seal. Follow the Service Procedure to correct the condition.
SSM 473982018-09-10. Service bulletin. POWER TRAIN; ENGINE; EQUIPMENT. Some 2015-2018 Edge vehicles equipped with a 2.0L EcoBoost and 6F35 transmission may exhibit a rattle noise from the transmission bellhousing area while running. This may be the result of a cracked engine flexplate. When replacing the flexplate, lubricate the torque converter pilot hub with Multi-Purpose Grease XL-5-A (ESB-M1C93-B) before reassembling. Make sure the transmission locator dowel pins are correctly installed. If the dowel pins were pulled out of the engine block, new dowel pins will need to be installed in the engine block. Failure to do so could result in a repeat repair. Refer to Workshop Manual (WSM), Section 307-01A. Engineering is investigating, monitor OASIS for updates. To assist with the investigation use the Report a Vehicle Concern link at the bottom of the OASIS report and fill out the form.
SSM 470002018-06-11. Service bulletin. ENGINE; POWER TRAIN:TRANSFER CASE (4-WHEEL DRIVE). Some 2013-2018 Escape/Fusion/MKZ vehicles equipped with 2.5L or 1.5L/2.0L/3.0L Ecoboost engine, 2015-2018 MKC/Edge/Explorer vehicles equipped with 2.0L/2.3L/2.7L EcoBoost engine, 2016-2018 MKX vehicles equipped with 2.7L Ecoboost engine, 2017-2018 Continental vehicles equipped with 2.7L/3.0L EcoBoost, and AWD may exhibit a fluid leak from the PTU intermediate shaft seal. Replacement of the intermediate shaft seal seal does not require removal of the PTU and does not require the use of the cover seal and bolt kit (CV6Z-7275-K) to perform the repair. Refer to the Workshop Manual (WSM), Section 308-07.
SSM 470002018-05-29. Service bulletin. ENGINE AND ENGINE COOLING. Some 2013-2018 Escape/Fusion/MKZ vehicles equipped with 2.5L or 1.5L/2.0L/3.0L Ecoboost engine, 2015-2018 MKC/Edge/Explorer vehicles equipped with 2.0L/2.3L/2.7L EcoBoost engine, 2016-2018 MKX vehicles equipped with 2.7L Ecoboost engine, 2017-2018 Continental vehicles equipped with 2.7L/3.0L EcoBoost, and AWD may exhibit a fluid leak from the PTU intermediate shaft seal. Replacement of the intermediate shaft seal seal does not require removal of the PTU and does not require the use of the cover seal and bolt kit (CV6Z-7275-K) to perform the repair. Refer to the Workshop Manual (WSM), Section 308-07.
SSM 472652018-05-21. Service bulletin. ENGINE AND ENGINE COOLING. Some Ford and Lincoln vehicles equipped with a 2.7L or 3.0L EcoBoost engines may exhibit an oil leak from the engine oil pan RTV seal. Replace the oil pan by performing the published Workshop Manual (WSM) service procedures. After removing the oil pan, it is suggested to allow the crankcase to drain overnight to minimize the chance of residual oil contaminating the crankcase sealing rail. Remove all traces of old RTV, clean the engine sealing surface with only Motorcraftù Metal Brake Parts Cleaner then wipe with Motorcraftù Metal Surface Prep Wipes, and allow to air dry as directed in WSM, Section 303-00, RTV Sealing Surface Cleaning and Preparation. If possible, after the new oil pan is installed, allow the new RTV sealant to cure for 4 hours before refilling the engine with oil. Ford is investigating this concern. Monitor OASIS for future updates.
SSM 472302018-05-21. Service bulletin. EQUIPMENT; ENGINE AND ENGINE COOLING. Some 2007-2016 Edge/MKX/Flex/MKT/MKZ/MKS/Taurus/Police Interceptor Sedan/Explorer/Police Interceptor Utility vehicles equipped with AWD and built on or before 30-Jun-2016 may exhibit a propane or natural gas odor during idle or low speed driving. This may be due to break down of the power transfer unit (PTU) fluid caused by excessive heat. If the source of the odor is identified as originating from the PTU, an idler bearing repair kit is available to repair the PTU. Refer to the Workshop Manual (WSM), Section 308-07. If the PTU is determined to be repairable, utilize kit GB5Z-7P258-A and the included instruction sheet. For claiming use causal part 7P258 and applicable labor operations in section 07 of the Service Labor Time Standards (SLTS) Manual.
SSM 472042018-05-21. Service bulletin. ENGINE AND ENGINE COOLING. Some 2015-2018 Fusion/MKZ/MKC/Escape/Edge vehicles equipped with a 2.0L EcoBoost engine may exhibit a runs rough condition with DTCs P0300, P0301, P0302, P0303, P0304 and/or P0316. This may be due to coolant intrusion due to corrosion on the engine block. To diagnose this concern, with the engine at normal operating temperature, pressurize the cooling system to 138 kPa (20 psi) and hold for 5 hours. If the coolant pressure drops 27.57 kPa (4psi), remove the spark plugs and inspect for coolant in the cylinders. If coolant is found in any of the cylinders, replace the engine long block assembly. Follow normal prior approval process for your Dealership. However, follow the diagnostic repair procedure in this article to determine correct repair. For claiming, use causal part 6006 and applicable labor operations in Section 6 of the SLTS Manual.
TSB18-20572018-05-14. Service bulletin. ENGINE AND ENGINE COOLING:EXHAUST SYSTEM. Some 2015-2018 Edge and 2016-2018 MKX vehicles may exhibit an exhaust odor in the vehicle while the climate control system is in auto or recirculation mode. Customers may indicate the odor smells like sulfur or exhaust odors are entering the vehicle cabin. This concern may be more pronounced after hard acceleration, driving in hilly conditions and/or towing a trailer. Whether and to what extent any occupant of these vehicles experiences the exhaust odor will be affected by driving habits, weather, and individual sensitivities. Follow the Service Procedure steps to correct the condition.
SSM 469062018-01-29. Service bulletin. ENGINE AND ENGINE COOLING; ELECTRICAL SYSTEM. Some 2015-2018 F150/Edge, 2016-2018 MKX and 2017-2018 Fusion, Continental vehicles equipped with a 2.7L engine may experience a malfunction indicator lamp (MIL) and/or wrench lamp with Diagnostic Trouble Codes (DTCs): P0116, P0117, P0118, P0119, P0217, P0330, P1026, and/or P130D. This may be due to a engine coolant temperature (ECT) sensor connector which is not fully seated or damaged wiring between connectors C1064 and C1047 for F150 and C1016 and C1168 for Edge/MKX/Fusion/Continental vehicles. ECT sensors should not be replaced if damaged wiring is found at or near these connectors. If an issue with the wiring is found use causal part 12A699.
SSM 460852017-08-01. Service bulletin. ENGINE AND ENGINE COOLING:EXHAUST SYSTEM:EMISSION CONTROL; ENGINE AND ENGINE COOLING:EXHAUST SYSTEM:MANIFOLD/HEADER/MUFFLER/TAIL PIPE; ENGINE AND ENGINE COOLING:EXHAUST SYSTEM:EMISSION CONTROL:CATALYTIC CONVERTOR; ENGINE AND ENGINE COOLING:EXHAUST SYSTEM:EMISSION CONTROL:GAS RECIRCULATION VALVE (EGR VALVE); ENGINE AND ENGINE COOLING:ENGINE:OTHER FUEL TYPES:TURBO/SUPERCHARGER; ENGINE AND ENGINE COOLING:COOLING SYSTEM:HOSES/LINES/PIPING/FITTINGS; ENGINE AND ENGINE COOLING; ENGINE AND ENGINE COOLING:COOLING SYSTEM:RADIATOR ASSEMBLY; ENGINE; ENGINE AND ENGINE COOLING:EXHAUST SYSTEM:EMISSION CONTROL:CRANKCASE (PCV); ENGINE AND ENGINE COOLING:COOLING SYSTEM; ENGINE AND ENGINE COOLING:ENGINE:GASOLINE:TURBO/SUPERCHARGER; ENGINE AND ENGINE COOLING:ENGINE:DIESEL; ENGINE AND ENGINE COOLING:EXHAUST SYSTEM; ENGINE AND ENGINE COOLING:ENGINE:GASOLINE; ENGINE AND ENGINE COOLING:ENGINE:GASOLINE:BELTS AND ASSOCIATED PULLEYS; ENGINE AND ENGINE COOLING:ENGINE; ENGINE AND ENGINE COOLING:COOLING SYSTEM:FAN. The Powertrain Control/Emissions Diagnosis (PC/ED) manual has been revised for diagnosing electronic throttle bodies (ETBs). The ETC_ACT and ETC_DSD PIDs should not used to diagnose possible ETB concerns. The IDS has a limited refresh rate when reading these PIDs and cannot display quickly enough to validate a concern. The PCM automatically monitors these inputs more accurately and will set diagnostic trouble codes (DTCs) when appropriate. Using these PIDs for diagnostics will lead to inaccurate results and improper ETB replacements. If a concern is intermittent and no DTCs are present, refer to historical DTCs and the PC/ED, Section 3 No DTCs Present Index chart for further information.
TSB 16-01282017-08-01. Service bulletin. ENGINE. Some 2015 Edge vehicles equipped with a 2.0L GTDI engine may exhibit an illuminated MIL with diagnostic trouble codes (DTCs) P0054, P0137 and/or P0141 stored in the powertrain control module (PCM) memory. Follow the Service Procedure steps to correct the condition.
SSM 465222017-08-01. Service bulletin. ENGINE AND ENGINE COOLING; EQUIPMENT. 2013-2017 Edge/MKX/Flex/MKT/MKZ/MKS/Taurus/Taurus Police/Explorer/Explorer Police/Continental vehicles equipped with a 3.5L or 3.7L engine, all wheel drive (AWD) and a power transfer unit (PTU) that is being repaired or replaced for an internal failure must also have the vent hose replaced due to contamination in the hose.
TSB 17-00352017-05-15. Service bulletin. ENGINE AND ENGINE COOLING:EXHAUST SYSTEM. SOME 2015-2017 EDGE AND 2016-2017 MKX VEHICLES MAY EXHIBIT AN EXHAUST ODOR IN THE VEHICLE WHILE THE CLIMATE CONTROL SYSTEM IS IN AUTO OR RECIRCULATION MODE. CUSTOMERS MAY INDICATE THE ODOR SMELLS LIKE SULFUR, THE EXHAUST ODORS ARE ENTERING THE VEHICLE CABIN. THIS CONCERN MAY BE MORE PRONOUNCED AFTER HARD ACCELERATION, DRIVING IN HILLY CONDITIONS AND/OR TOWING A TRAILER. WHETHER AND TO WHAT EXTENT ANY OCCUPANT OF THESE VEHICLES EXPERIENCES THE EXHAUST ODOR WILL BE AFFECTED BY DRIVING HABITS, WEATHER, AND INDIVIDUAL SENSITIVITIES. FOLLOW THE SERVICE PROCEDURE STEPS TO CORRECT THE CONDITION.
SSM 461722017-03-20. Service bulletin. ENGINE. SOME 2015-2017 F-150, 2016 MKX, 2015 EDGE, 2017 FUSION, MKZ AND CONTINENTAL VEHICLES EQUIPPED WITH A 2.7L/3.0L ENGINE MAY APPEAR TO HAVE LOW ENGINE OIL LEVEL IF THE PROPER PROCEDURES ARE NOT FOLLOWED. REFER TO THE OWNERS GUIDE, MAINTENANCE, ENGINE OIL CHECK SECTION. WHEN CHECKING THE ENGINE OIL LEVEL AFTER SHUTTING OFF THE ENGINE WAIT AT LEAST 15 MINUTES PRIOR TO CHECKING IN ORDER TO ALLOW THE OIL TO DRAIN BACK TO THE OIL PAN. THE ENGINE OIL LEVEL CAN BE CHECKED IMMEDIATELY IF THE ENGINE HAS NOT BEEN STARTED. WHEN CHANGING THE ENGINE OIL THE ENGINE NEEDS TO BE AT NORMAL OPERATING TEMPERATURE AND THE OIL FILTER REMOVED BEFORE DRAINING THE OIL. ALLOW THE OIL PAN TO DRAIN COMPLETELY FOR UP TO 5 MINUTES. CHECK OIL LEVEL AFTER FILLING BY FOLLOWING THE OIL LEVEL CHECK PROCEDURE.
SSM 463412017-03-15. Service bulletin. ENGINE. WHEN SERVICING A 2.7L OR 3.0L ECOBOOST ENGINE, IF THE CRANKSHAFT PULLEY IS REMOVED, CORRECT REASSEMBLY IS CRITICAL TO PREVENT POTENTIAL ENGINE FAILURE. THIS INCLUDES INSTALLING A NEW CRANKSHAFT PULLEY BOLT AND ACCURATELY PERFORMING EACH STAGE OF THE CRANKSHAFT PULLEY BOLT TORQUE SEQUENCE. CRANKSHAFT PULLEY RELATED WORKSHOP MANUAL (WSM) PROCEDURE AND RECOMMENDED TOOL (OTC 4754 OR EQUIVALENT) INFORMATION HAVE BEEN UPDATED. REFER TO THE APPLICABLE WSM, SECTION 303-01, FOR ADDITIONAL INFORMATION.
SSM 462812017-03-11. Service bulletin. ENGINE. SOME 2015-2017 EDGE/MKX, ESCAPE/MKC, FUSION/MKZ AND EXPLORER VEHICLES EQUIPPED WITH A 2.0L OR 2.3L MAY EXHIBIT DAMAGE TO THE ENGINE APPEARANCE COVER, VALVE COVER AND/OR INTAKE MANIFOLD WHEN ATTEMPTING TO REMOVE THE APPEARANCE COVER. TO REDUCE THE POSSIBILITY OF DAMAGE, CAREFULLY PULL STRAIGHT UPWARD ON THE UNDERSIDE OF THE COVER AT EACH FASTENER LOCATION TO REMOVE. DO NOT PULL THE COVER FORWARD OR TO THE SIDE. BEFORE INSTALLING THE ENGINE APPEARANCE COVER, APPLY MOTORCRAFT SILICONE BRAKE CALIPER GREASE AND DIELECTRIC COMPOUND (XG-3-A) TO THE COVER FASTENER GROMMETS. WORKSHOP MANUAL (WSM) INFORMATION IS IN THE PROCESS OF BEING UPDATED
SSM 462532017-03-10. Service bulletin. ENGINE. SOME 2015-2016 EDGE WITH 2.0L GASOLINE TURBOCHARGED DIRECT INJECTION (GTDI), 2015-2016 MUSTANG AND F-150 WITH 5.0L ENGINE AND 2016 EXPLORER EQUIPPED WITH 2.3L GTDI ENGINE MAY EXHIBIT OIL LEAK AT ENGINE OIL PRESSURE (EOP) SENSOR THREADS. IT IS NOT REQUIRED TO REPLACE THE SENSOR IF IT IS LEAKING FROM THE THREADS. REMOVE AND RESEAL THE EOP SENSOR, REFER TO WORKSHOP MANUAL (WSM), SECTIONS 303-14. CHECK THE OIL LEVEL AND TOP OFF AS NECESSARY. REFER TO WSM, SECTION 303-01. USE CAUSAL PART 9278 AND APPLICABLE LABOR OPERATIONS IN SECTION 09 OF THE SERVICE LABOR TIME STANDARDS (SLTS) MANUAL
SSM 459362017-02-13. Service bulletin. ELECTRICAL SYSTEM; ENGINE AND ENGINE COOLING. SOME 2015-2016 EDGE AND 2016 MKX VEHICLES BUILT ON OR BEFORE 6/11/2016 MAY EXHIBIT A NOISE FROM THE ELECTRIC COOLING FANS, MOST NOTICEABLE RIGHT AFTER THE ENGINE IS TURNED OFF AS THEY SPIN DOWN TO A STOP. IF THE NOISE CAN BE PINPOINTED TO THE COOLING FAN MOTOR, INSTALL A NEW COOLING FAN MOTOR AND SHROUD F2GZ-8C607-E WHICH WAS RELEASED FOR SERVICE TO RESOLVE THIS CONCERN.
TSB16-00942017-02-10. Service bulletin. FUEL/PROPULSION SYSTEM; ENGINE. SOME 2015-2016 EDGE AND 2016 MKX VEHICLES EQUIPPED WITH A 2.7L ECOBOOST ENGINE AND BUILT ON 10/29/2015 AND THROUGH 4/1/2016 MAY EXHIBIT A KNOCKING/TAPPING NOISE THAT CAN BE HEARD IN THE FUEL FEED TUBE THAT ATTACHES TO THE HIGH PRESSURE FUEL PUMP ON THE ENGINE. THIS MAY BE DUE TO A LOOSE CHECK VALVE LOCATED IN THE FUEL FEED TUBE. FOLLOW THE TSB SERVICE PROCEDURE STEPS TO CORRECT THE CONDITION.
TSB 16-01392017-02-04. Service bulletin. ENGINE. SOME 2015-2016 F-150, C-MAX, EDGE, MKS, TAURUS, AND FLEX AND 2016 EXPEDITION, EXPLORER, ESCAPE, FUSION, MUSTANG, MKZ, MKX, NAVIGATOR, TRANSIT AND TRANSIT CONNECT VEHICLES EQUIPPED WITH A 2.0L, 2.5L, 3.5L OR 3.7L GASOLINE ENGINE AND BUILT ON OR BEFORE 31-MAY-2016 MAY EXHIBIT AN INTERMITTENT LOSS OF POWER AND/OR AN ILLUMINATED POWERTRAIN MALFUNCTION (WRENCH) LAMP WITH DIAGNOSTIC TROUBLE CODES (DTCS) P2111, P2112 AND/OR P2119 STORED IN POWERTRAIN CONTROL MODULE (PCM) MEMORY. FOLLOW THE SERVICE PROCEDURE STEPS TO CORRECT THE CONDITION.
TSB-15-01232016-06-22. Service bulletin. ENGINE; POWER TRAIN:AUTOMATIC TRANSMISSION:CONTROL MODULE (TCM/PCM/TECM). SUMMARY TO BE PROVIDED ON A FUTURE DATE.
ASI-452242015-10-21. Service bulletin. ENGINE. FORD/LINCOLN: SOME VEHICLES WILL EXPERIENCE, BETWEEN INTAKE VALVE AND THROTTLE BODY, AND AIR LEAK IN ENGINE. MODEL 2015 F-150, EDGE, MKX. *PE

The summaries are NHTSA's. Each bulletin's page links NHTSA's copy of the manufacturer's document.