WenmarOpen by Wenmar Pro

Service bulletins for the 2014 Dodge Journey

A bulletin is a manufacturer's communication to its dealers, as NHTSA indexes it. The summary is NHTSA's. The document is the manufacturer's: read it at NHTSA. A bulletin is not a recall, and listing a model year does not mean every vehicle of it is concerned.

214 on file from NHTSA, as of 2026-10-19.

By type

By component

By trouble code

Bulletins, newest first
90036942018-06-11. Service bulletin. ENGINE AND ENGINE COOLING. Oil Pump Assembly If error code P06DD present on any Pentastar V6 application, please inspect oil pump for relief valve failure. See photo attached. If valve is found out of place please call Bob Jackson (248) 944-0466 bob.jackson@fcagroup.com, or Joe Lovell (734) 309-6467 joe.lovell@fcagroup.com before proceeding. If unable to reach after 15 minutes record the following information and proceed with oil pump replacement and hold part for return to FCA via Fastrack system
90036812018-06-11. Service bulletin. SEAT BELTS. Restraints Information Sheet (I-Sheet) has been added to Star Parts. Print I-Sheet for technician use.
90036872018-06-11. Service bulletin. SEAT BELTS. Restraints Remove I-Sheet from packaging. Correct information sheet (I-Sheet) has been added to Star Parts. Print I-Sheet for technician use.
68277402A2018-06-11. Service bulletin. VEHICLE SPEED CONTROL:CRUISE CONTROL. Adaptive Cruise Control Sensor 1) If you are replacing this part due to the cluster displaying Clean Radar Sensor in Front of Vehicle or DTC C1266 ACC Sensor Blinded, please verify that there is no blockage in front of the sensor. Blockage can occur from mud, ice, snow, front end damage, bracket damage, the sensor not attached to the bracket properly or an aftermarket fascia installed. This fault can occur intermittently in muddy or icy/snowy conditions and is considered normal operation. Under some circumstances, a misaligned sensor can also cause the C1266 DTC, please complete an alignment procedure. No replacement is required.~ 2) If you are replacing this part due to the cluster displaying ?ACC/FCW Unavailable Service Required?, please check the DTC fault codes. This will indicate which module needs to be serviced (TCM, PCM, ESP/ABS, etc). This fault is not due to the ACC Sensor. No sensor replacement is required.~ 3) If you have fault code DTC C125E ACC Sensor Adjustment Required, please verify that the radar sensor is fully seated in the clips and there is no damage (if clips are damaged on a 2013 or earlier vehicle, order P/N 68085813A$, otherwise please replace the module), please verify there is no blockage to the sensor due to mud, ice, snow, front end damage, bracket damage or the sensor not attached to the bracket properly. Perform the Vertical Alignment and the Electronic Horizontal Alignments procedure as stated in the service manual. Please note, if the horizontal alignment procedure will not complete, check the vertical alignment and confirm that the sensor is seated properly. Rerun the horizontal alignment procedure. No sensor replacement is required. **Hints for running Horizontal Alignment procedure: A) Verify speed is between 45 and 75 mph, B) verify the road is relatively straight with signs, poles, guard rails, etc C) Do not tail a vehicle too closely this inhibits the learning procedure
68234120A2018-06-11. Service bulletin. EQUIPMENT:ELECTRICAL:RADIO/TAPE DECK/CD ETC.; ELECTRICAL SYSTEM:SOFTWARE. Panasonic 8.4" CTP/FCTP Radio, Update Failure Issue 1: Hand Free Module inoperative, can't pair phone: - Do not replace the radio for phone issues. The Radio does not control phone/Hands Free functionality, it is separate from the radio, test and diagnose the Hands Free Module accordingly.~ Issue 2; Radio inoperative, no power, display no power or screen is blank.~ Blank Screen with Audio: The ICS is a separate module from the radio. If attempting to replace the display (ICS), do not order a radio part number. Instead, order p/n Z5064993A$ for an exchange or 05064993A$ for a new part replacement.~ Issue 3.; If the radio ICS/touchscreen display appears to reset intermittently, it turns white then black and functionality returns....Please contact Leony Gonzalez at cell (248) 736-1267 or Dave Clemons at cell (248) 520-0419. Engineering is currently root causing this issue and your assistance is greatly appreciated. If unable to reach this person within 15 minutes, then proceed with the necessary repair. NOTE: USB cables should be replaced prior to the HFM or Radio.
68105583A2018-06-11. Service bulletin. ENGINE AND ENGINE COOLING. Pentastar Oil Filter Adapter: Before replacing this part, please call any one of the following people. Engineering is seeking information regarding this part.~ Dye must be used to determine where the leak is coming from before replacing. Also please check the recently updated Service Bulletin Number 09-008-15. ~ First: Nick Morand Cell (248) 410-8078 - Nick.morand@fcagroup.com Second: Bob Jackson Cell (248) 944-0466 - bob.jackson@fcagroup.com Third: Joe Lovell Cell (734 309-6467 - joe.lovell@fcagroup.com If a response is not received within 15 mins, then proceed with the necessary repair.~
18-023-14 REV. A2018-06-11. Service bulletin. POWER TRAIN. Flash: 2.4L, 3.6L Powertrain System Improvements/Enhancements This bulletin involves reprogramming the Powertrain Control Module (PCM) with the latest available software. The following powertrain system improvements/enhancements are included in this software release:Vehicles equipped with a 2.4L engine (sales code ED3 or ED7). Charging system duty cycle enhancement to improve starting performance in low ambient temperatures. P219A - Bank 1 Air-Fuel Ratio Imbalance. (applies to vehicles equipped with the 4 speed transmission (sales code DFF) only. Enhanced Automatic Oil Change Indicator(EAOCI) system enhancements that force the use of the severe duty cycle algorithm anytime the PCM is replaced. The vehicle duty cycle information used in the EAOCI calculation is stored in the PCM and cannot be recovered/transferred when the controller is replaced. As a result, the severe duty cycle is used in these scenarios to ensure the customer receives a timely oil change required message. Mode 6 data accuracy enhancement for generic scan tools.Vehicles equipped with a 3.6L engine (sales code ERB). Enhanced Automatic Oil Change Indicator(EAOCI) system enhancements that force the use of the severe duty cycle algorithm anytime the PCM is replaced. The vehicle duty cycle information used in the EAOCI calculation is stored in the PCM and cannot be recovered/transferred when the controller is replaced. As a result, the severe duty cycle is used in these scenarios to ensure the customer receives a timely oil change required message. Mode 6 data accuracy enhancement for generic scan tools.
18-059-142018-06-11. Service bulletin. POWER TRAIN. Flash: Improved High Altitude Performance This bulletin involves selectively erasing and reprogramming the Powertrain Control Module (PCM) with new software. The customer may complain of less then desired engine performance at high altitude.
18-054-142018-06-11. Service bulletin. ENGINE AND ENGINE COOLING. Intermittent Extended Crank, Long Crank Time. This bulletin involves inspecting the Bank 1 Camshaft Position Sensor serial number and if necessary, replacing the sensor. A small number of customers may experience an intermittent 1 to 5 second extended crank condition when starting their vehicle. No DTCs will be present when this occurs.
08-066-142018-06-11. Service bulletin. ELECTRICAL SYSTEM. Flash: RE9 Radio Enhancements This bulletin involves updating the radio and navigation software, if required. A customer may experience, one or more of the following conditions: Navigation screen locks up or display will be blank. Navigation feature lockout disable. Navigation system resets intermittently. Translation improvements/corrections. System consistency and operational improvements for menu selections, month/date formatting, and Garmin translation functions. Radio system improvements during remote start operation. Unable to adjust radio volume using steering wheel switch intermittently. Second screen is blank when using split screen function. Add China phone book search. Some functionality changes for China- keyboard, search, sort and jump. Unable to add contacts to the favorite list. Unable to dial the phone from the radio, while still able to dial from the phone. Unable to delete a cell phone number from the favorite list. More space available for phone book entries. BlackBerry support for playing songs. Reduce ticking noise during CD/USB pause and VR is silent between prompts. VR unable to transition from Non-navigation to navigation mode. iPod screen is displayed with navigation screen. Asian language translation added. Highlighted preset continues blinking. Takes more then one button press to select preset #10. Unable to adjust volume from steering wheel switches. Clock adjust pop up message displayed in English rather than current language. Can not connect to the phone after it has been disconnect. Teleprompter screen shows incomplete text. Some functionality for traffic & weather jump button. After changing a language and then selecting CDDA ?of? is displayed as a tracking number. In ?Set Date Year? only 3 digits are displayed. Split map view will not cancel. Map screen turns black when driving. Some pop up message characters is displayed with ?!#?. Traffic programming slow to start.
18-034-142018-06-11. Service bulletin. ENGINE AND ENGINE COOLING. P0520- Engine Oil Pressure Sensor Circuit This bulletin involves replacing the oil pressure sensor with a revised part. A small number of customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the Technician may find that the following Diagnostic Trouble Code (DTC) has been set: P0520 - Engine Oil Pressure Sensor Circuit
24-002-142018-06-11. Service bulletin. EQUIPMENT:ELECTRICAL. Driver And Passenger HVAC Blower Air Temperatures Are Not The Same When ?Sync? Setting Mode Is Selected And Headlamps Always Stay On. This bulletin involves selectively replacing the solar sensor. Customers may experience the following condition: When using the Automatic Temperature Control ?SYNC? mode, left and right outlet temperatures do not match regardless of the desired temperature setting is the same. Occupants will experience being cold (winter time), on either passenger or driver side, even though the temperature setting is the same. Headlamps are always staying on, when they are set to Auto mode.
18-023-142018-06-11. Service bulletin. ENGINE. Flash: Powertrain System Improvements/Enhancements This bulletin involves selectively erasing and reprogramming the Powertrain Control Module (PCM) with new software. The following powertrain system improvements/enhancements are included in this software release: ? Enhanced Automatic Oil Change Indicator(EAOCI) system enhancements that force the use of the severe duty cycle algorithm anytime the PCM is replaced. The vehicle duty cycle information used in the EAOCI calculation is stored in the PCM and cannot be recovered/transferred when the controller is replaced. As a result, the severe duty cycle is used in these scenarios to ensure the customer receives a timely oil change required message. ? Corrected a generic scan tool display issue regarding Mode 6 data accuracy. ? Improved Electronic Voltage Regulator control to more precisely maintain system voltage.
09-001-142018-05-21. Service bulletin. ENGINE AND ENGINE COOLING. Hard Contact Knocking Noise In Engine Compartment Primarily While Turning Left This bulletin involves replacing the rear engine mount bracket. Hard contact knocking noise in the engine compartment caused by contact between the Rear Engine Mount Bracket and the fastener on the Power Transfer Unit (PTU). Noise heard primarily while turning left.
90025192018-02-21. Service bulletin. EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL. 82212076, 82203694 - Fabric Cleaner This "fabric cleaner" is not intended for sale in California, the otc states (Connecticut, Delaware, Massachusetts, Maine, New Hampshire, New Jersey, New York, Pennsylvania, Virginia, and Washington dc), and some ladco states (Illinois, Michigan, and Ohio). Mopar offers an alternative product (82213192) which is a water based product approved for sale in the aforementioned states.~ ~ Please inform the customer & your prep dept that spraying excessive amounts of the fabric protector on load floors will result in the breaking down of the adhesive (glue) that is used to create the bond between the fabric (carpet) and the load floor. This will apply to any vehicles equipped with rear load floors such as WK, WD, PM, MK, KA, KK. The carpet will appear to be loose, wrinkly, or bunch up~
RL108213A$2017-11-03. Service bulletin. ENGINE AND ENGINE COOLING. NAG1 (5A580) Valve Body As per Warranty Bulletin D-13-22, please use R2108213A$ valve body for all Warranty (W), Mopar (M) and Mopar Vehicle Protection (F) claims.~ Assembly also includes Filter (52108325AA) and Gasket (52108332AA).~
08-055-17 REV. A2017-11-03. Service bulletin. ELECTRICAL SYSTEM:SOFTWARE. Flash: Hands Free Module Software Enhancements This bulletin involves reprogramming the Hands Free Module (HFM) with the latest available software. The customer may experience the following:HFM does not boot properly. "Hands-Free Module Loading" displayedon the head unit.TheHFM is inoperative and unresponsive to all user input.TheHFM is unresponsive and appears off the bus to wiTECH.Inaccurate foreign language translations.VoiceRecognition (VR) is sluggish after changing the language.IPhone®4 starts auto recording itself.Backgroundnoise from Automated Speech Recognition. When in Bluetooth® Streaming Audio (BTSA) mode, the display will show?Music paused connecting phone? while a song is beingplayed and without an incoming call. Wrong BTSA screen when deleting. Whenin Text To Speech (TTS), it will be a mix of the TTS and recording. IPod®touch, BTSA will not Audio Stream.Integratedcenter stack screen will display ?music paused? afterignition was cycled and BTSA was being used before the ignition wasturned off.AutomaticSound Recognition (ASR) Microphone picking up background noise.WithSales code RSQ, when the language is set for Italian and after theignition is cycled, the phone screens will change to English.No response from the VR button on the steering wheel.Notbeing able to enter into the phone screen on the radio.Technicians may find Diagnostic Trouble Code (DTC) U0197-00 Lost CommunicationWith Hands Free Phone Module, is set. Thecustomer may note when trying to select a non-supported language likeRussian or Portuguese, the Hands Free screen will default to English.The VR will default back to the last language (Italian, French, Spanish,German or Dutch) the customer was using.After the software update has been completed, both the hands free screen and VR will default back to the last language used.Enhancements now include all vehicles, not just internationalvehicles.The following software enhancement isincluded:VR Teleprompter
90033552017-11-03. Service bulletin. ENGINE AND ENGINE COOLING. 3.2L - 3.6L Cylinder Head Assy Multiple cylinder head replacement. If a cylinder head is replaced on a vehicle more than 1 time for any reason, please call any of the following people. First: Joe Lovell - Cell (734) 309-6467 joe.lovell@fcagroup.com Second: Kevin Refalo - Cell (248) 260-0738 Kevin.refalo@facgroup.com If no response in 15 minutes, proceed with repair.
18-086-162017-11-03. Service bulletin. ENGINE AND ENGINE COOLING; BACK OVER PREVENTION; STRUCTURE; EXTERIOR LIGHTING; ELECTRICAL SYSTEM. Flash: Powertrain Diagnostic and System ImprovementsThis bulletin involves selectively erasing and reprogramming the Powertrain Control Module (PCM) with new software. A small number of customers may experience the following symptom or conditions or a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find the following (DTCs):JC Vehicles equipped with a 2.4L engine (Sales Code ED3 or ED7):· **P0335 - Crankshaft Position Sensor Circuit. · P050B - Cold Start Ignition Timing Performance.· P2299 - Brake Pedal Position / Accelerator Pedal Position Incompatible.**· U0140 - Lost Communication With Body Control Module. Attempting to clear the DTC may be unsuccessful.· P0456 - Evap purge system small leak.· 2-1 downshift improvement.· Charging system duty cycle enhancement to improve starting performance in low ambient temperatures.· P219A - Bank 1 Air-Fuel Ratio Imbalance.· Enhanced Automatic Oil Change Indicator (EAOCI) system enhancements that forcethe use of the severe duty cycle algorithm anytime the PCM is replaced. The vehicleduty cycle information used in the EAOCI calculation is stored in the PCM and cannot be recovered/transferred when the controller is replaced. As a result, the severe duty cycle is used in these scenarios to ensure the customer receives a timely oil change required message.· Mode 6 data accuracy enhancement for generic scan tools. JC Vehicles equipped with a 3.6L engine (Sales Code ERB):· **P0335 - Crankshaft Position Sensor Circuit.· P2610 - PCM Internal Engine Off Timer Performance.**· U0140 - Lost Communication With Body Control Module. Attempting to clear theDTC may be unsuccessful.· Enhanced Automatic Oil Change Indicator (EAOCI) system enhancements that forcethe use of the severe duty cycle algorithm anytime the PCM is replaced. The vehicleduty cycle information used in the EAOCI calculation is stored in the PCM and cannot be recovered/transferred when the controll
68141352A$2017-11-03. Service bulletin. ENGINE AND ENGINE COOLING. 3.2L - 3.6L Cylinder Head Assy Multiple cylinder head replacement. If cylinder head is replaced on a vehicle more than 1 time for any reason, please call any of the following people.~ First: Ron Dallison ? Cell (248) 292-9510 Ron.dallison@fcagroup.com ~ Second: Joe Lovell - Cell (734) 309-6467 joe.lovell@fcagroup.com~ If a response is not received within 15 mins, then proceed with the necessary repair.
68234120A$2017-11-03. Service bulletin. EQUIPMENT; EQUIPMENT:ELECTRICAL; ELECTRICAL SYSTEM; EQUIPMENT:ELECTRICAL:RADIO/TAPE DECK/CD ETC.. Panasonic 8.4" CTP/FCTP Radio, Update Failure Issue 1: Hand Free Module inoperative, can't pair phone: - Do not replace the radio for phone issues. The Radio does not control phone/Hands Free functionality, it is separate from the radio, test and diagnose the Hands Free Module accordingly.~ Issue 2; Radio inoperative, no power, display no power or screen is blank.~ Blank Screen with Audio: The ICS is a separate module from the radio. If attempting to replace the display (ICS), do not order a radio part number. Instead, order p/n Z5064993A$ for an exchange or 05064993A$ for a new part replacement.~ Issue 3; If the radio ICS/touchscreen display appears to reset intermittently, it turns white then black and functionality returns....Please contact Leony Gonzalez at cell (248) 736-1267 or Dave Clemons at cell (248) 520-0419. Engineering is currently root causing this issue and your assistance is greatly appreciated. If unable to reach this person within 15 minutes, then proceed with the necessary repair. NOTE: USB cables should be replaced prior to the HFM or Radio.
R652017-10-21. Service bulletin. ELECTRICAL SYSTEM:SOFTWARE. Reprogram Radio Control Head The radio navigation system on about 30,300 of the above vehicles may experience a condition which permanently renders the navigation features not functional as a result of memory corruption. The radio navigation will be checked for functionality. If functional, the radio and navigation software levels must be checked. If software is found to be outdated, the radio control head will need to be reprogrammed with the latest radio and/or navigation software. If the navigation was found to not be functional, the radio will need to be replaced. Order the replacement radio through the audio and electronic products exchange center. Then return the vehicle to the customer and inform the customer that a return visit will need to be scheduled for radio replacement once the replacement radio arrives.
R61 (15V-675)2017-10-21. Service bulletin. SERVICE BRAKES; ELECTRICAL SYSTEM. Antilock Brake System Control Module Anti-Lock Brake System (ABS) control module on about 275,600 of the above vehicles may have a ground wire eyelet on the right front shock tower that allows water to wick through the ground wire case and into the ABS module. Moisture in the ABS module could disable the ABS and/or Electronic Stability Control (ESC) system(s). The lack of a functioning ABS and/or ESC system(s) could change the braking and/or handling characteristics of the vehicle and cause a crash without warning.
08-015-162017-10-13. Service bulletin. EQUIPMENT:ELECTRICAL:NAVIGATIONAL SYSTEM(GLOBAL POSITIONING SYSTEM). Poor GPS Signal Reception This bulletin involves the replacement of the GPS antenna with a roof mount antenna to improve navigation performance. The customer may experience off route conditions due to weak navigation satellite signal.
68105583A$2016-09-15. Service bulletin. EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL; ELECTRICAL SYSTEM. "PENTASTAR OIL FILTER ADAPTER BEFORE REPLACING THIS PART, PLEASE CALL ANY ONE OF THE FOLLOWING PEOPLE. ENGINEERING IS SEEKING INFORMATION REGARDING THIS PART.~ DYE MUST BE USED TO DETERMINE WHERE THE LEAK IS COMING FROM BEFORE REPLACING. ALSO PLEASE CHECK THE RECENTLY UPDATED SERVICE BULLETIN NUMBER 09-008-15. ~ FIRST: NICK MORAND CELL (248) 410-5078 - NICK.MORAND@FCAGROUP.COM SECOND: BOB JACKSON CELL (248) 944-0466 - BOB.JACKSON@FCAGROUP.COM THIRD: JOE LOVELL CELL (734 309-6467 - JOE.LOVELL@FCAGROUP.COM IF A RESPONSE IS NOT RECEIVED WITHIN 15 MINS, THEN PROCEED WITH THE NECESSARY REPAIR."

The summaries are NHTSA's. Each bulletin's page links NHTSA's copy of the manufacturer's document.