WenmarOpen by Wenmar Pro

Service bulletins for the 2022 Dodge Durango

A bulletin is a manufacturer's communication to its dealers, as NHTSA indexes it. The summary is NHTSA's. The document is the manufacturer's: read it at NHTSA. A bulletin is not a recall, and listing a model year does not mean every vehicle of it is concerned.

418 on file from NHTSA, as of 2026-10-19.

By type

By component

By trouble code

Only bulletins with component: Engine are shown. Show all

Bulletins, newest first
09005232024-01-02. Service bulletin. ENGINE AND ENGINE COOLING; FUEL SYSTEM, GASOLINE:FUEL INJECTION SYSTEM:THROTTLEBODY/MANIFOLD. Loose Air Duct Connection at Throttle Body Customer may experience the following: ? Poor engine performance. ? Drone noise from the engine area. This bulletin involves inspecting and if necessary tightening the clamp on the air duct assembly to the throttle Body
9003357A2024-01-02. Service bulletin. ENGINE AND ENGINE COOLING. ADAPTER, Engine Oil Filter (Pentastar V6) For all 2014MY replace the Oil Filter Adapter (OFA). For any other MY review and follow instructions from the latest STAR Online S1809000007 available on Dealer Connect. Also, consider the following: 1) Remove OFA 2) Replace only the oil inlet O-ring and gaskets (seals kit in SOL above). 3) Re-install the OFA. For 2023MY and beyond use black O-ring. For 2022MY and prior use red O-ring. Note: When replacing OFA, it may be necessary to transfer the Oil Temp/Pressure Sensor from the old OFA to the new OFA.
91002122023-10-30. Service bulletin. ELECTRICAL SYSTEM; ENGINE AND ENGINE COOLING; ENGINE AND ENGINE COOLING:COOLING SYSTEM:PUMP. PUMP Water For 2016-2024MY 3.6L Pentastar Upgrade with suspected coolant leak. PRIOR TO PERFORMING ANY WATER PUMP REPLACEMENT, PROCEED WITH INSPECTION INSTRUCTIONS FROM THE LATEST VERSION OF STAR ONLINE PUBLICATION S2307000002. Please submit pictures of the leak area thru the DIDI process outlined in the STAR Online document. NOTE: Some coolant residue may be found at the water pump weep hole plug area which may be normal, but coolant should not be dripping from this location. If unsure about, use the Pressurized Coolant System Inspection process as found in the Dealer Connect Cooling Diagnosis and Testing Procedures.
S23070000022023-10-02. Service bulletin. ENGINE AND ENGINE COOLING. Suspected engine coolant leak.
S23230000212023-07-31. Service bulletin. ENGINE AND ENGINE COOLING. Clunk Noise From Front End Driving Between 15 And 35 MPH And When Decelerating. C0604- Active Air Dam Control Performance
0900923b2023-07-31. Service bulletin. ENGINE AND ENGINE COOLING. Engine makes an abnormal ticking noise. There may be Diagnostic Trouble Codes (DTCs) present.
0900923a2023-07-31. Service bulletin. ENGINE AND ENGINE COOLING. Engine makes an abnormal ticking noise. There may be Diagnostic Trouble Codes (DTC)s present.
07007232023-07-31. Service bulletin. ENGINE AND ENGINE COOLING. Water Quality When Mixed With Engine Coolant
09009232023-07-31. Service bulletin. ENGINE AND ENGINE COOLING. Engine Ticking Noise Engine makes an abnormal ticking noise. There may be Diagnostic Trouble Codes (DTC)s present. This bulletin involves inspecting and if needed, replacing the intake HLAs. NOTE: **ALL VEHICLES ON THE RSU VIN LIST REQUIRE ALL 12 INTAKE HYDRAULIC LASH ADJUSTERS TO BE REPLACED**.
91001432023-07-31. Service bulletin. ENGINE AND ENGINE COOLING:ENGINE:CRANK/CAMSHAFT POSITION SENSOR. PSU right intake camshaft Case 1) If you are to flash the PSU (Pentastar Upgrade Engine) PCM due to P0300 code presence, only AB or previous LEVEL PSU right intake camshaft PN 05047913AA or AB (old version) should be replaced. If the engine is equipped with the AC/AD LEVEL PSU right intake camshaft PN 05047913AC or AD (new version), camshaft should NOT be replaced. Case 2) If the intake camshaft or intake rocker arm has excessive wear on the high lift profile (Rocker arm: slider, Camshaft: central lobe), replace the intake camshaft (1) in that cylinder head and all intake rocker arms (6).
09009232023-05-30. Service bulletin. ENGINE AND ENGINE COOLING. Engine Ticking Noise Engine makes an abnormal ticking noise. There may be Diagnostic Trouble Codes (DTC)s present. This bulletin involves inspecting and if needed, replacing the intake HLAs.
18048232023-05-30. Service bulletin. EQUIPMENT; ENGINE AND ENGINE COOLING. wiTECH Small Leak Verification Test (SLVT) - P0456-EVAP SYSTEM SMALL LEAK
09005232023-04-17. Service bulletin. ENGINE AND ENGINE COOLING. Loose Air Duct Connection at Throttle Body Customer may experience the following: ? Poor engine performance. ? Drone noise from the engine area. This bulletin involves inspecting and if necessary tightening the clamp on the air duct assembly to the throttle Body
9003357a2023-04-17. Service bulletin. ENGINE AND ENGINE COOLING. ADAPTER, Engine Oil Filter (Pentastar V6) For all 2014MY replace the Oil Filter Adapter (OFA). For any other MY review and follow instructions from the latest STAR Online S1809000007 available on Dealer Connect. Also, consider the following: 1) Remove OFA 2) Replace only the oil inlet O-ring and gaskets (seals kit in SOL above). 3) Re-install the OFA. For 2023MY and beyond use black O-ring. For 2022MY and prior use red O-ring. Note: When replacing OFA, it may be necessary to transfer the Oil Temp/Pressure Sensor from the old OFA to the new OFA.
90033572023-04-17. Service bulletin. ENGINE AND ENGINE COOLING. ADAPTER, Engine Oil Filter (Pentastar V6) For all 2014MY replace the Oil Filter Adapter (OFA). For any other MY (with mileage above 30,000) review and follow instructions from STAR Online S1809000007 REV. C available on Dealer Connect. Also, consider the following: 1) Remove OFA 2) Replace only the oil inlet O-ring and gaskets (seals kit in SOL above). 3) Re-install the OFA. For 2023MY and beyond use black O-ring. For 2022MY and prior use red O-ring. Note: When replacing OFA, it may be necessary to transfer the Oil Temp/Pressure Sensor from the old OFA to the new OFA.
91001322023-04-17. Service bulletin. ENGINE AND ENGINE COOLING. ENGINE ASSY - 3.6L AUTO TRANS Before replacing the engine due to an abnormal ticking noise, please check that the INTAKE Hydraulic Lash Adjusters are not "collapsed". If a collapsed INTAKE HLA is found, replace all INTAKE HLAs on the suspect cylinder head. The noise can occur at low or high RPMs, and at low or high temperatures. There are no Diagnostic Trouble Codes (DTC)s present. CAUSE: INTAKE Hydraulic Lash Adjuster may have a manufacturing issue that can cause the plunger to stick, generating valvetrain noise.
91001032023-01-17. Service bulletin. ENGINE AND ENGINE COOLING. Engine Oil - 0W20,Fluid - ATF+4,Engine Oil - 10W30,Engine Oil - 5W20,Engine Oil - 5W30
S21090000042023-01-17. Service bulletin. ENGINE AND ENGINE COOLING. Issue involves overheating, running hot, coolant leaks and related symptoms after a Mopar replacement engine has been installed in the vehicle.
07-005-222023-01-17. Service bulletin. FUEL SYSTEM, GASOLINE; ENGINE AND ENGINE COOLING. 6.4L Rubbed Through Coolant Hose This bulletin involves inspecting the oil cooler coolant hose and possibly replacing it. Customers may experience the following: An engine coolant leak under the hood. This coolant leak is caused from the oil coolercoolant hose contacting the engine serpentine belt resulting in a rub through condition on the oil cooler hose.
S22080000732023-01-09. Service bulletin. ENGINE AND ENGINE COOLING:ENGINE:ENGINE CONTROL MODULE (ECU/ECM). No Start, After Flash And Or PCM Replace, DTC P0513 Invalid Skim Key Setting
S22090000022023-01-09. Service bulletin. ENGINE. Customer complaints may include abnormal engine noise, rough idle, lack of power, misfire. When performing diagnosis, an internal engine concern may be suspected.
90044872023-01-09. Service bulletin. STRUCTURE; ENGINE AND ENGINE COOLING; AIR BAGS; POWER TRAIN. Transmission Oil Pan and Gasket Assembly For Transmission oil leaks, need to identify exactly where the leak is coming from, please check the transmission case at the Trans Oil Heater (TOH) connection on the Grand Cherokee's. Also check the Trans Valve Body at the TCM harness connection. A black light can be used to identify trans fluid vs. other fluids. Contact FCA Redacted Content prior to replacing these components. If no response in 15 minutes, proceed with repair. Please email pictures of leak locations to FCA Redacted Content
S22090000042022-12-19. Service bulletin. EQUIPMENT; ENGINE AND ENGINE COOLING. If a Mopar oil filter is not available, use a filter that meets or exceeds USCAR36 specification and is compatible with semi and full synthetic oils.
91000822022-11-07. Service bulletin. POWER TRAIN; ELECTRICAL SYSTEM; WHEELS; EQUIPMENT; ENGINE AND ENGINE COOLING; ELECTRICAL SYSTEM:STARTER ASSEMBLY:SOLENOID. STARTER, Engine Prior to starter removal: 1. Inspect and check all connections to the starter motor solenoid a. Unplug and plug-in the T50 1-way connector as needed to verify the connection is good & tight and check for any bent pin in the connection. b. Inspect the T30 connection (i.e. B+ M8 threaded stud & nut) for tightness to assure cable ring terminal connection is secured and tight (use torque spec per service manual). 2. Check/verify all grounds in the cranking circuit a. Check tightness of mounting bolts that secure starter to the engine block b. Check main ground from engine to chassis c. Check battery ground cable connections are clean and tight d.Potentially, loosen both starter motor bolts, without removing, and re-tighten to torque specifications in the service manual e. After all steps above are complete, attempt to crank the engine to verify if improvement has been made (i.e. the steps fixed the customer complaint) 3. Conduct the voltage drop test (starter feed circuit) per the service manual before removing the starter motor 4. Starter Removal: conduct the removal if above steps do not fix the complaint a. Conduct bench test by applying 12 volts to motor T30 and T50 connections (i.e. conduct simple free speed test) b. Free speed test should result in starter motor pinion travel to pinion stop and rotation with normal rotational noise (i.e. no grinding, scrapping, etc.) c. If any abnormal noise is present, replace the starter motor 5. During starter removal, also remove and replace the two starter mounting bolts. Return the bolts with starter motor for analysis at QEC and the supplier warranty analysis lab.
S22090000022022-10-17. Service bulletin. ENGINE. Customer complaints may include abnormal engine noise, rough idle, lack of power, misfire. When performing diagnosis, an internal engine concern may be suspected.

The summaries are NHTSA's. Each bulletin's page links NHTSA's copy of the manufacturer's document.