Service bulletins for the 2015 Dodge Challenger
A bulletin is a manufacturer's communication to its dealers, as NHTSA indexes it. The summary is NHTSA's. The document is the manufacturer's: read it at NHTSA. A bulletin is not a recall, and listing a model year does not mean every vehicle of it is concerned.
350 on file from NHTSA, as of 2026-10-19.
By type
By component
By trouble code
Only bulletins with component: Transmission and driveline are shown. Show all
| S2621000003 REV.A | 2026-03-18. Service bulletin. POWER TRAIN. The vehicle will exhibit a service transmission/check engine warning indicator for the following transmission models: 845RE, 8HP45, 850RE, 8HP50, 8HP70, 8HP75, 8HP75-PHEV, 8HP75-LCV, 8HP90, 8HP95. Transmissions may exhibit the following diagnostic codes: P07E4, P1DB2, P0716, P1B14, P0733, P1D90, P1DB7, P1B13. |
|---|---|
| 2103014 | 2023-01-17. Service bulletin. EQUIPMENT; POWER TRAIN. Transmission Quick Learn Procedure |
| W56 | 2023-01-09. Service bulletin. POWER TRAIN. Customer Satisfaction Notification W56 Reprogram Powertrain Control Module |
| 9003704 | 2023-01-09. Service bulletin. ENGINE AND ENGINE COOLING; POWER TRAIN. Transmission Oil Pan, Heater (TMU), Tube or O-ring Applies to vehicles equipped with 8 speed transmissions only; if you have a leak that appears to be at the pan the use of proper leak detection is recommended. The fluid in the 8 speeds can be detected with a black light and there are aftermarket spray on leak detection materials to help ensure that the leak is properly diagnosed and not from another location such as cooler lines, heater tubes, or case porosity. Please note that the transmission pan gasket is available for many of the 8 speed applications FCA offers. Please review the available quick connect and transfer tube parts, as replacement of the TMU may not be required. If a TOC line connection is found to be the source, the quick connect may need replacement. If the leak source is coming from the connection of the TMU to the transmission, the transfer tube may need replacement. When parts are returned to the QEC the retaining clips (snap ring) for the quick disconnect fittings are missing. (This leaves a question as to whether the clips were missing from the assembly plant, or the technician removed them in order to make line removal easier.) Please return the clips with the transmission heater and note if they were not there to begin with. For any questions regarding transmission heater, contact FCA Redacted Content. If no response in 15 minutes, proceed with repair. |
| 1801615 | 2023-01-09. Service bulletin. POWER TRAIN; SERVICE BRAKES, HYDRAULIC; ELECTRICAL SYSTEM; EXTERIOR LIGHTING. Flash: 6.2L Powertrain Diagnostic And System Enhancements This bulletin involves reprogramming the Powertrain Control Module (PCM) with the latest available software. A small number of customers may experience a Malfunction Indicator Lamp (MIL) Illumination. Upon further investigation, the technician may find one or more of the following Diagnostic Trouble Codes (DTCs) stored in the PCM memory. ? P0300 - Multiple Cylinder Misfire (manual transmission applications only). ? P1613 - Turbocharger/Supercharger Boost Pressure Sensor/Mass Air Flow Sensor Correlation. ? P2227 - Barometric Pressure Circuit Performance In addition, customers may also comment that, with the cluster set on metric units, they are unable to accurately increase or decrease the cruise control set speed using the resume or set buttons. Instead of changing vehicle speed by 1 KPH when pressing the buttons, the vehicle speed will increase approximately 1.6 KPH. |
| 1900115 | 2023-01-09. Service bulletin. STEERING; POWER TRAIN. Loss Of Power Steering Assist This bulletin involves inspecting the steering gear pinion cover retaining washer and if not present, replacing the steering gear. Pinion Shaft Cover Retaining Washer Missing. The customer may describe loss of power steering assist. |
| 2100915 | 2023-01-09. Service bulletin. ELECTRICAL SYSTEM; POWER TRAIN; EQUIPMENT; EXTERIOR LIGHTING. Flash: Transmission Shift And Drivability Enhancements This bulletin involves reprogramming the Transmission Control Module (TCM) with the latest available software. A small number of customers may experience one or more of the following concerns. These concerns are broken up per engine and transmission combination. 6.2L engine (sales code ESD) equipped with an 8HP90 transmission (sales code DFE) ? Transmission will not upshift during Wide Open Throttle (WOT) acceleration. ? Harsh or inconsistent coasting downshifts. ? Transmission will not shift into 7th gear during high speed driving. ? Inconsistent or busy shifts during stop and go traffic. ? Inconsistent gear shift patterns when driving on grades. ? Malfunction Indicator Lamp (MIL) Illumination during ABS activated stops with Diagnostic Trouble Code (DTC) P1DCD TCM Monitoring Processor Performance, Multiple Clutches Locked Up. 6.4L engine (sales code ESG) and equipped with an 8HP70 transmission (sales code DFK) ? Harsh or inconsistent 1-2 upshift. ? Harsh of inconsistent coasting 4-3 downshift. ? Harsh or inconsistent gear engagement when shifting to drive or reverse. ? Instrument Panel Cluster (IPC) shows the incorrect gear when in manual mode. ? Harsh of inconsistent shifts during tip-in acceleration from closed throttle. ? Inconsistent gear shift patterns when driving on grades. ? Inconsistent release of Hill Start Assist during tip-in acceleration. ? Transmission upshifts on sweeping curves under track driving conditions. |
| 2102016 | 2022-12-19. Service bulletin. EQUIPMENT; BACK OVER PREVENTION; POWER TRAIN. Manual Transmission Shifter Noise This bulletin involves greasing or replacing the manual transmission rear shifter bushing. Customers may experience a clunk, squeak, or similar noise heard from center console area while shifting. |
| V51 | 2022-12-19. Service bulletin. POWER TRAIN:AUTOMATIC TRANSMISSION:CONTROL MODULE (TCM/PCM/TECM); UNKNOWN OR OTHER. Customer Satisfaction Notification V51 Reprogram Powertrain Control Module |
| 9003704 | 2022-10-31. Service bulletin. POWER TRAIN; ENGINE AND ENGINE COOLING. Trans Oil Pan, Heater Tube or O-ring, Heater Applies to vehicles equipped with 8 speed transmissions only; If you have a leak that appears to be at the pan the use of proper leak detection is recommended. The fluid in the 8 speeds can be detected with a black light and there are aftermarket spray on leak detection materials to help ensure that the leak is properly diagnosed and not from another location such as cooler lines, heater tubes, or case porosity. If you have a leak concern please note that the transmission pan gasket is available for many of the 8 speed applications FCA offers. See your parts specialist for the proper gasket for the repair. |
| 1804716 | 2022-10-24. Service bulletin. POWER TRAIN. Powertrain Diagnostic And System Enhancements |
| 1804516 | 2022-10-24. Service bulletin. POWER TRAIN. 6.4L Diagnostic And System Improvements |
| 0809220 | 2022-10-17. Service bulletin. POWER TRAIN; STEERING. Improper Up Shift With Paddle Shift This bulletin involves replacing both steering wheel paddle shifter. Customers may experience the following:When trying to upshift using the paddle shifter on the steering, the transmission will downshift instead. |
| 1801615 | 2022-10-17. Service bulletin. POWER TRAIN. Flash: 6.2L Powertrain Diagnostic And System Enhancements This bulletin involves reprogramming the Powertrain Control Module (PCM) with the latest available software. A small number of customers may experience a Malfunction Indicator Lamp (MIL) Illumination. Upon further investigation, the technician may find one or more of the following Diagnostic Trouble Codes (DTCs) stored in the PCM memory. ? P0300 - Multiple Cylinder Misfire (manual transmission applications only). ? P1613 - Turbocharger/Supercharger Boost Pressure Sensor/Mass Air Flow Sensor Correlation. ? P2227 - Barometric Pressure Circuit Performance In addition, customers may also comment that, with the cluster set on metric units, they are unable to accurately increase or decrease the cruise control set speed using the resume or set buttons. Instead of changing vehicle speed by 1 KPH when pressing the buttons, the vehicle speed will increase approximately 1.6 KPH. |
| 2100915 | 2022-10-17. Service bulletin. POWER TRAIN:AUTOMATIC TRANSMISSION:CONTROL MODULE (TCM/PCM/TECM); POWER TRAIN. Flash: Transmission Shift And Drivability Enhancements This bulletin involves reprogramming the Transmission Control Module (TCM) with the latest available software. A small number of customers may experience one or more of the following concerns. These concerns are broken up per engine and transmission combination. 6.2L engine (sales code ESD) equipped with an 8HP90 transmission (sales code DFE) ? Transmission will not upshift during Wide Open Throttle (WOT) acceleration. ? Harsh or inconsistent coasting downshifts. ? Transmission will not shift into 7th gear during high speed driving. ? Inconsistent or busy shifts during stop and go traffic. ? Inconsistent gear shift patterns when driving on grades. ? Malfunction Indicator Lamp (MIL) Illumination during ABS activated stops with Diagnostic Trouble Code (DTC) P1DCD TCM Monitoring Processor Performance, Multiple Clutches Locked Up. 6.4L engine (sales code ESG) and equipped with an 8HP70 transmission (sales code DFK) ? Harsh or inconsistent 1-2 upshift. ? Harsh of inconsistent coasting 4-3 downshift. ? Harsh or inconsistent gear engagement when shifting to drive or reverse. ? Instrument Panel Cluster (IPC) shows the incorrect gear when in manual mode. ? Harsh of inconsistent shifts during tip-in acceleration from closed throttle. ? Inconsistent gear shift patterns when driving on grades. ? Inconsistent release of Hill Start Assist during tip-in acceleration. ? Transmission upshifts on sweeping curves under track driving conditions. |
| 1807320 | 2022-09-26. Service bulletin. ELECTRICAL SYSTEM; POWER TRAIN. Flash: Powertrain Control Module (PCM) Updates This bulletin involves reprogramming the Powertrain Control Module (PCM) with the latest software. Customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find one or more of the following Diagnostic Trouble Codes (DTCs):U1424-00 - Implausible Engine Torque Signal Received(2015 MY). P0456 - EVAP System Small Leak. P2610 - PCM Internal Engine Off Timer Performance. P2299 - Brake Pedal Position / Accelerator Pedal Position Incompatible. P0335 - Crankshaft Position Sensor Circuit(2014-2015 MY). U0140 - Lost Communication With Body Control Module(LC, LD and LX). P1621 - O2 Sensor Reference Voltage Circuit Low. P1622 - O2 Sensor Reference Voltage Circuit High. P0606 - Internal Control Processor. P0300 - Multiple Cylinder Misfire. P219A - Bank 1 Air-Fuel Ratio Imbalance. P219B - Bank 2 Air-Fuel Ratio Imbalance. P0307 - Cylinder 7 Misfire. P2096 - Downstream Fuel Trim System 1 Lean. P2097 - Downstream Fuel Trim System 1 Rich. The following software enhancements are also available(2015 MY):Reverse gear lock-out change from 16 kph (10 mph) to 4.8 kph (3 mph)(Sales Code EZC with DEC). Change to purge vapor control calibration(Sales Code EZH with DGJ). Improvements to vehicle overspeed control(Sales Code EZH with DGJ). Calibration update to the electronic voltage regulator voltage set point(Sales Code EZH with DGJ). Additional Symptoms:Customers with a Pursuit Dodge Charger (LD) may describe an unpleasant odor in the vehicle under certain extreme ambient conditions2013-2015 MY LD with (Sales Codes EZH with AHB or AHV only). Technicians may find that the original vehicle Frequency Operated Button Integrated Key (FOBIK) does not function properly following replacement of the Wireless Ignition Node (WIN/WCM). The Secret Key information stored in the PCM may be corrupt. This update will restore the PCM?s ability to store/transfer valid Secret Key information |
| W56 | 2022-09-26. Service bulletin. POWER TRAIN. Customer Satisfaction Notification W56 Reprogram Powertrain Control Module |
| 9003704 | 2022-09-26. Service bulletin. SEATS; FUEL SYSTEM, GASOLINE; AIR BAGS; POWER TRAIN; BACK OVER PREVENTION; ENGINE AND ENGINE COOLING. Transmission Oil Pan, Heater (TMU), Tube or O-ring Applies to vehicles equipped with 8 speed transmissions only; if you have a leak that appears to be at the pan the use of proper leak detection is recommended. The fluid in the 8 speeds can be detected with a black light and there are aftermarket spray on leak detection materials to help ensure that the leak is properly diagnosed and not from another location such as cooler lines, heater tubes, or case porosity. Please note that the transmission pan gasket is available for many of the 8 speed applications FCA offers. Please review the available quick connect and transfer tube parts, as replacement of the TMU may not be required. If a TOC line connection is found to be the source, the quick connect may need replacement. If the leak source is coming from the connection of the TMU to the transmission, the transfer tube may need replacement. When parts are returned to the QEC the retaining clips (snap ring) for the quick disconnect fittings are missing. (This leaves a question as to whether the clips were missing from the assembly plant, or the technician removed them in order to make line removal easier.) Please return the clips with the transmission heater and note if they were not there to begin with. For any questions regarding transmission heater, contact FCA Redacted Content. If no response in 15 minutes, proceed with repair. |
| 18-016-15 | 2022-09-26. Service bulletin. EXTERIOR LIGHTING; ELECTRICAL SYSTEM; POWER TRAIN. Flash: 6.2L Powertrain Diagnostic And System Enhancements This bulletin involves reprogramming the Powertrain Control Module (PCM) with the latest available software. A small number of customers may experience a Malfunction Indicator Lamp (MIL) Illumination. Upon further investigation, the technician may find one or more of the following Diagnostic Trouble Codes (DTCs) stored in the PCM memory. ? P0300 - Multiple Cylinder Misfire (manual transmission applications only). ? P1613 - Turbocharger/Supercharger Boost Pressure Sensor/Mass Air Flow Sensor Correlation. ? P2227 - Barometric Pressure Circuit Performance In addition, customers may also comment that, with the cluster set on metric units, they are unable to accurately increase or decrease the cruise control set speed using the resume or set buttons. Instead of changing vehicle speed by 1 KPH when pressing the buttons, the vehicle speed will increase approximately 1.6 KPH. |
| 19-001-15 | 2022-09-26. Service bulletin. STEERING; POWER TRAIN. Loss Of Power Steering Assist This bulletin involves inspecting the steering gear pinion cover retaining washer and if not present, replacing the steering gear. Pinion Shaft Cover Retaining Washer Missing. The customer may describe loss of power steering assist. |
| 21-009-15 | 2022-09-26. Service bulletin. EXTERIOR LIGHTING; POWER TRAIN; ELECTRICAL SYSTEM; EQUIPMENT. Flash: Transmission Shift And Drivability Enhancements This bulletin involves reprogramming the Transmission Control Module (TCM) with the latest available software. A small number of customers may experience one or more of the following concerns. These concerns are broken up per engine and transmission combination. 6.2L engine (sales code ESD) equipped with an 8HP90 transmission (sales code DFE) ? Transmission will not upshift during Wide Open Throttle (WOT) acceleration. ? Harsh or inconsistent coasting downshifts. ? Transmission will not shift into 7th gear during high speed driving. ? Inconsistent or busy shifts during stop and go traffic. ? Inconsistent gear shift patterns when driving on grades. ? Malfunction Indicator Lamp (MIL) Illumination during ABS activated stops with Diagnostic Trouble Code (DTC) P1DCD TCM Monitoring Processor Performance, Multiple Clutches Locked Up. 6.4L engine (sales code ESG) and equipped with an 8HP70 transmission (sales code DFK) ? Harsh or inconsistent 1-2 upshift. ? Harsh of inconsistent coasting 4-3 downshift. ? Harsh or inconsistent gear engagement when shifting to drive or reverse. ? Instrument Panel Cluster (IPC) shows the incorrect gear when in manual mode. ? Harsh of inconsistent shifts during tip-in acceleration from closed throttle. ? Inconsistent gear shift patterns when driving on grades. ? Inconsistent release of Hill Start Assist during tip-in acceleration. ? Transmission upshifts on sweeping curves under track driving conditions. |
| S1821000001 | 2022-09-26. Service bulletin. POWER TRAIN. Gear Ratio DTC?s, Transmission Shift Concerns, Does Not Shift At Times, Shudders |
| 9004009 | 2022-09-26. Service bulletin. POWER TRAIN. Transmission Kit with Torque Converter 1. All Promaster (VF) 3.6L/62TE equipped vehicles. If the transmission bracket to the transmission case fasteners are removed during servicing, the fasteners (Part Number 06511385A$) are one-time usage. Vehicles built prior to 10/23/2015 requires Service Kit PN 68461214AA; includes Transmission Isolator PN 68264483AA, and Adaptation Bracket 68264479AA and Fastener Service Kit PN 68329056AA Vehicles built after on or after 10/23/2015 will require only the Fastener Service Kit PN 68329056AA. 2. All 3.6L/62TE equipped vehicles. If the vehicle you are repairing has a crack in the flex plate or failed pump bushing inspect and confirm that both (2) dowel pins are present in the engine block, which align the transmission center line to the crank shaft centerline and visually inspect the dowel alignment holes in the transmission case. If the holes are damaged or elongated the transmission should be replaced to prevent further damage to the transmission/flexplate or pump bushing due to the inability to properly align the engine to the transmission during the repair. 3. All 62TE equipped vehicles. If pump bushing is scored or damaged and the dowel pin alignment holes are ok, replace the pump assembly as opposed to complete transmission. 4. All 62TE equipped vehicles. If vehicle is jerking/slipping with MIL code(s) P0740 or P2764, check TCC Solenoid operation. If TCC Solenoid is ok, the codes are indicative of a torque converter failure. Replace the torque converter. |
| 2103014 | 2022-09-26. Service bulletin. POWER TRAIN. 845RE Transmission Quick Learn Procedure This bulletin provides information on how to perform the new scan tool based transmission Quick Learn procedure. This procedure is required after certain transmission repairs or to remedy a customer?s concern of poor shift quality. Customers may indicate that their transmission shift quality does not meet their expectations. |
| 2101214 | 2022-09-26. Service bulletin. POWER TRAIN. 8 Speed Transmission Shift Adaptation, Drive Learn Procedure This bulletin involves performing a Transmission Adaptation Learn procedure based on a subjective shift quality rating evaluation.The adaptation drive learn procedure must be performed on all 8-speed transmissions when the transmission is repaired/replaced and/or the Valve Body/TCU assembly (mechatronic) is replaced, or when the adaptation memory cells are cleared with the wiTECH diagnostic scan tool. Customers may indicate that their transmission shift quality does not meet their expectations. |
The summaries are NHTSA's. Each bulletin's page links NHTSA's copy of the manufacturer's document.