WenmarOpen by Wenmar Pro

Service bulletins for the 2008 Dodge Caliber

A bulletin is a manufacturer's communication to its dealers, as NHTSA indexes it. The summary is NHTSA's. The document is the manufacturer's: read it at NHTSA. A bulletin is not a recall, and listing a model year does not mean every vehicle of it is concerned.

51 on file from NHTSA, as of 2026-10-19.

By type

By component

By trouble code

Only bulletins with component: Transmission and driveline are shown. Show all

Bulletins, newest first
90042662022-10-17. Service bulletin. POWER TRAIN. TRANSMISSION, 5 Speed On replacing OE transmission 05106567A$/68042567A$ with reman transmission R8142074A$ replace with new Hydraulic Clutch Tube 05273429A$ to avoid interference with shift lever
90040092022-09-26. Service bulletin. POWER TRAIN. Transmission Kit with Torque Converter 1. All Promaster (VF) 3.6L/62TE equipped vehicles. If the transmission bracket to the transmission case fasteners are removed during servicing, the fasteners (Part Number 06511385A$) are one-time usage. Vehicles built prior to 10/23/2015 requires Service Kit PN 68461214AA; includes Transmission Isolator PN 68264483AA, and Adaptation Bracket 68264479AA and Fastener Service Kit PN 68329056AA Vehicles built after on or after 10/23/2015 will require only the Fastener Service Kit PN 68329056AA. 2. All 3.6L/62TE equipped vehicles. If the vehicle you are repairing has a crack in the flex plate or failed pump bushing inspect and confirm that both (2) dowel pins are present in the engine block, which align the transmission center line to the crank shaft centerline and visually inspect the dowel alignment holes in the transmission case. If the holes are damaged or elongated the transmission should be replaced to prevent further damage to the transmission/flexplate or pump bushing due to the inability to properly align the engine to the transmission during the repair. 3. All 62TE equipped vehicles. If pump bushing is scored or damaged and the dowel pin alignment holes are ok, replace the pump assembly as opposed to complete transmission. 4. All 62TE equipped vehicles. If vehicle is jerking/slipping with MIL code(s) P0740 or P2764, check TCC Solenoid operation. If TCC Solenoid is ok, the codes are indicative of a torque converter failure. Replace the torque converter.
90042662020-07-27. Service bulletin. POWER TRAIN. TRANSMISSION, 5 Speed On replacing OE transmission 05106567A$/68042567A$ with reman transmission R8142074A$ replace with new Hydraulic Clutch Tube 05273429A$ to avoid interference with shift lever
H-322008-12-15. Service bulletin. POWER TRAIN:AUTOMATIC TRANSMISSION:CONTROL MODULE (TCM/PCM/TECM); ENGINE AND ENGINE COOLING:EXHAUST SYSTEM:EMISSION CONTROL. CHRYSLER DODGE SERVICE CAMPAIGN: SEE DOCUMENT SEARCH BUTTON FOR OWNER LETTER. VEHICLES MAY HAVE BEEN INADVERTENTLY PROGRAMMED WITH SOFTWARE THAT DISABLED THREE ENGINE DIAGNOSTIC MONITORS. WITHOUT MONITORS, AN IMPROPERLY OPERATING COMPONENT MAY GO UNDETECTED AND RESULT IN EXCESSIVE EXHAUST EMISSIONS. *PE CSC LETTER WAS RECEIVED. 1/23/09. *PE
1801108 REVB2008-08-06. Service bulletin. POWER TRAIN:AUTOMATIC TRANSMISSION:CONTROL MODULE (TCM/PCM/TECM). FLASH: MIL ILLUMINATION WITH DTC P0139 OR 02270. THIS BULLETIN INVOLVES SELECTIVELY ERASING AND REPROGRAMMING THE POWERTRAIN CONTROL MODULE (PCM). *PE
21-014-082008-06-17. Service bulletin. POWER TRAIN:AUTOMATIC TRANSMISSION:CONTROL MODULE (TCM/PCM/TECM). FLASH: INCORRECT REPORTING OF DTC P0730 FOR DTC P0717. *NJ
18-019-082008-06-03. Service bulletin. POWER TRAIN:AUTOMATIC TRANSMISSION:CONTROL MODULE (TCM/PCM/TECM). FLASH: MIL ILLUMINATION WITH DTC P2173. *NJ
18-017-082008-06-03. Service bulletin. POWER TRAIN:AUTOMATIC TRANSMISSION:CONTROL MODULE (TCM/PCM/TECM). FLASH: IDLE VIBRATION FROM A STOP WITH CLOSED THROTTLE. *NJ
18-016-082008-06-03. Service bulletin. POWER TRAIN:AUTOMATIC TRANSMISSION:CONTROL MODULE (TCM/PCM/TECM). FLASH: MIL ILLUMINATION WITH DTC P0171. *NJ
18-022-082008-06-03. Service bulletin. POWER TRAIN:AUTOMATIC TRANSMISSION:CONTROL MODULE (TCM/PCM/TECM). FLASH: IDLE OSCILLATION AFTER FUEL FILL WITH OR WITHOUT CLICKING SOUND FROM ENGINE COMPARTMENT. *NJ
18-020-082008-05-30. Service bulletin. POWER TRAIN:AUTOMATIC TRANSMISSION:CONTROL MODULE (TCM/PCM/TECM). FLASH: MIL ILLUMINATION WITH DTC P0300 AND/OR P0301 AND/OR P0302 AND/OR P0303 AND/OR P0304 SET. *NJ
18-011-082008-05-02. Service bulletin. POWER TRAIN:AUTOMATIC TRANSMISSION:CONTROL MODULE (TCM/PCM/TECM). FLASH: MILL ILLUMINATION WITH DTC P0139 OR P2270. *NJ
21-011-082008-05-02. Service bulletin. POWER TRAIN:MANUAL TRANSMISSION. GEAR CLASH/DIFFICULT TO SHIFT - THIS BULLETIN INVOLVES REPLACING THE 3RD/4TH/5TH & REVERSE GEAR SYNCHRONIZER (BLOCKER) RINGS TOGETHER AS A SET IF A DE-BONDING CONDITION IS FOUND. *NJ
18-014-082008-04-29. Service bulletin. POWER TRAIN:AUTOMATIC TRANSMISSION:CONTROL MODULE (TCM/PCM/TECM). FLASH: MIL ILLUMINATION WITH DTC P0234 AND/OR P0128. EQUIPPED WITH A 2.4L TURBO ENGINE BUILT PRIOR TO MARCH 4, 2008. *NJ

The summaries are NHTSA's. Each bulletin's page links NHTSA's copy of the manufacturer's document.