WenmarOpen by Wenmar Pro

Service bulletins for the 2025 Chrysler Pacifica

A bulletin is a manufacturer's communication to its dealers, as NHTSA indexes it. The summary is NHTSA's. The document is the manufacturer's: read it at NHTSA. A bulletin is not a recall, and listing a model year does not mean every vehicle of it is concerned.

219 on file from NHTSA, as of 2026-10-19.

By type

By component

By trouble code

Bulletins, newest first
S258A0000042025-02-06. Service bulletin. ELECTRICAL SYSTEM. DVD Or Blu-Ray INOP, Rear Screens Or Monitors INOP, VRM Audio INOP, Mirroring INOP
otherdoc_ 1302025-01-25. Other. STRUCTURE:BODY; SUSPENSION. PDI Updates
S25230000032025-01-16. Service bulletin. STRUCTURE:BODY. Door Latch, Handle And Ajar Additional Service Information.
91004682024-12-20. Service bulletin. UNKNOWN OR OTHER. FUEL VAPOR CANISTER FILTER EVAP Fuel Filters are to be checked for restriction / blockage on a regular schedule as indicated in the Owner s Manual. If the Filter is restricted or blocked then replace the part. For customers that drive light duty trucks in extreme dusty and dirty road conditions, please reference information only TSB 25-009-24 for an available MOPAR Dual EVAP Filter kit that is customer paid.
91004452024-12-12. Service bulletin. ELECTRICAL SYSTEM. Power Transfer Unit If considering PTU Assembly replacement related to DTCs C14A7-97 or C1494-92, please be aware of updated diagnostic procedures in the service library which may indicate the smart actuator replacement (PN 68369691AD) is the proper repair.
S2208000045 REV.B2024-12-11. Service bulletin. BACK OVER PREVENTION: REARVIEW SYSTEM BRAKING. Backup Camera Poor Image Quality Inspection
S2223000036 REV.A2024-11-22. Service bulletin. ELECTRICAL SYSTEM. Reverse View Camera Inoperative After Recent Repair
91004472024-11-20. Service bulletin. ELECTRICAL SYSTEM. SWITCH Multifunction Before replacing the steering column control module (SCCM) due to DTC U0212 active, please follow these steps: 1.- Refer to service library procedure and follow diagnosis steps at BCM. 2.- If failure still present, make sure all the switches' and airbag's harness are properly connected and there is no corrosion or pinching, disconnect the switches & reconnect them, and reverify the issue. 3.- Verify if failure is still present, review if there is lack of communication between SCCM and BCM. For example, activate turn signals or wipers. 4.- Read at the BCM diagnosis session if BCM is receiving information from SCCM. Through diagnosis review if activation from wipers is requested, if turn signal, blindspot and lane assistant work. 5.- Do a hard reset to BCM and evaluate if any DTC is set. Retest if failure still present. If there are no DTC's, physical defects, wipers inop, nor turn signal inop, then SCCM does not need to be replaced Before replacing the steering column control module (SCCM) due to DTC U0212 active, please follow these steps: 1.- Refer to service library procedure and follow diagnosis steps at BCM. 2.- If failure still present, make sure all the switches' and airbag's harness are properly connected and there is no corrosion or pinching, disconnect the switches & reconnect them, and reverify the issue. 3.- Verify if failure is still present, review if there is lack of communication between SCCM and BCM. For example, activate turn signals or wipers. 4.- Read at the BCM diagnosis session if BCM is receiving information from SCCM. Through diagnosis review if activation from wipers is requested, if turn signal, blindspot and lane assistant work. 5.- Do a hard reset to BCM and evaluate if any DTC is set. Retest if failure still present. If there are no DTC's, physical defects, wipers inop, nor turn signal inop, then SCCM does not need to be replaced.
S2422000001 REV.C2024-11-13. Service bulletin. WHEELS; ELECTRICAL SYSTEM. Tire Pressure Monitor (TPM) Service Information. TPM Lamp On.
18-082-242024-11-07. Service bulletin. POWER TRAIN. "Flash: Powertrain Control Module (PCM) Updates Customers may experience the following: ● Vehicle may enter “Auto Park Mode” during an Engine Stop Start (ESS) event. The driver will be notified that the vehicle is entering “Auto Park Mode” by the blinking D on the shifter for three blinks and then automatically shifting into Park. To shift out of Park, the driver will have to press down on the brake pedal and cycle the ignition back to START, and move the shifter into the desired position This bulletin involves reprogramming the PCM with the latest available software."
1007702024-11-01. Service bulletin. STRUCTURE:BODY; ELECTRICAL SYSTEM. SWITCH AND BEZEL - FRONT DOOR
999652024-11-01. Service bulletin. UNKNOWN OR OTHER. MODULE - INVERTER
91004382024-10-31. Service bulletin. AIR BAGS. MODULE Air Bag Control For vehicles with B2208, B00B5 or U0151 conditions, before replacing the ORC Module, check the circuit wiring and connector first for any Open or Shorted conditions and check vehicle for low-voltage conditions.
1004962024-10-02. Service bulletin. SUSPENSION. ISOLATOR - SPRING
1002092024-09-05. Warranty extension. UNKNOWN OR OTHER. Warranty Newsletter Volume 10 Issue 8_ID
S24080000982024-09-05. Service bulletin. ELECTRICAL SYSTEM; FORWARD COLLISION AVOIDANCE: WARNINGS; FORWARD COLLISION AVOIDANCE: ADAPTIVE CRUISE CONTROL. ACC Sensor Blinded, “ACC Unavailable Service Required” “FCW Unavailable Service Required”, Adaptive Cruise Control (ACC) system disabled, Loss of Advanced Driver Assist System (ADAS) Features Messages Displayed on the Instrument Panel Cluster (IPC)
91003892024-07-24. Service bulletin. ELECTRICAL SYSTEM. CAN Star Block Connector Customer finds MIL light on and technician finds DTC for loss of communication on one or more modules. In repair procedure the dealerships are replacing the CAN star block connector during their root cause process with returned parts showing no trouble found. Here is a list of steps the dealers can follow to determine if they have a defective CAN star block connector using a multimeter: Step 1: Visually review CAN star block for damage and ensure back cover has all locking tabs engaged. If a bent pin, cracked or damaged housing or locking tab is not engaged is observed then replacement is required. Step 2: Identify Connector #1 as the 3 Pin Connector cavity Step 3: Measure resistance between Pin#1 and Pin#2 in Connector #1. Acceptable values are 120.4 Ohms to 139.8 Ohms. If resistance is outside of this range then replacement is required. Step 4: Measure the continuity between Pin#1 in Connector #1 to Pin#1 in each of the other 2 Pin connector cavities. If continuity is not found then a replacement is required. Step 5: Measure the continuity between Pin#2 in Connector #1 to Pin#2 in each of the other 2 Pin connector cavities. If continuity is not found then a replacement is required.
S24080000762024-07-18. Service bulletin. ELECTRICAL SYSTEM. Malfunction Indicator Lamp on, Diagnostic Trouble Code (DTC) P0EDD-00 – Hybrid/EV battery Pack B Deterioration
979622024-07-02. Other. UNKNOWN OR OTHER. MOTOR - BLOWER WITH WHEEL

The summaries are NHTSA's. Each bulletin's page links NHTSA's copy of the manufacturer's document.