WenmarOpen by Wenmar Pro

Service bulletins for the 2016 Chrysler 300

A bulletin is a manufacturer's communication to its dealers, as NHTSA indexes it. The summary is NHTSA's. The document is the manufacturer's: read it at NHTSA. A bulletin is not a recall, and listing a model year does not mean every vehicle of it is concerned.

305 on file from NHTSA, as of 2026-10-19.

About P2299 on the 2016 Chrysler 300: what the code means, and the bulletins and recalls about the same components.

By type

By component

By trouble code

Only bulletins with trouble code: P2299 are shown. Show all

Bulletins, newest first
18075172022-10-24. Service bulletin. BACK OVER PREVENTION; SEAT BELTS; ELECTRICAL SYSTEM; POWER TRAIN; AIR BAGS; EXTERIOR LIGHTING. Flash: Powertrain Diagnostic and System Improvements This bulletin involves reprogramming of the Powertrain Control Module (PCM) with the latest software. Customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find that the following DTCs: P000B - Bank 1 Camshaft 2 Position Slow Response. P0016 - Crankshaft/Camshaft Timing Misalignment - Bank 1 Sensor 1. P0335 - Crankshaft Position Sensor Circuit. P0339 - Crankshaft Position Sensor Intermittent. P0441 - EVAP Purge System Performance. P0455 - EVAP System Large Leak. P2610 - PCM Internal Engine Off Timer Performance. P0456 - EVAP System Small Leak. P2299 - Brake Pedal Position/Accelerator Pedal Position Incompatible. Customers may also notice the following condition(s): Brief engine idle fluctuation while in hot ambient temperatures. A slight hesitation during light pedal application after engine cold start. Driveline noises. Engine stumble/hesitation on a very hard pedal acceleration from a dead stop. Transmission enhancements during low-speed braking turning maneuvers. False detonation (spark knock) detected during a wide-open throttle (LA Challenger Sales Codes ESH with DEC only). In addition, the following software enhancements are available: Reduce bumps felt on light to medium decal braking and coming to a stop. Launch spark improvement change from 35 MPH to 10 MPH. Reverse lock out speed change from 10 MPH to 3 MPH (Sales Code DEC only). Torque security calibration changes to desensitize brake throttle override entry conditions. Calibration changes to address engine speed undershoot/overshoot during clutch disengagement when coming to a stop (Sales Code DEC only). Start fuel and transient fuel calibration change for improved drivability robustness. Purge calibration changes for a more robust purge volume result at altitude. Individual Cylinder Fuel Control (ICFC) calibration changes for improved fueling offset accuracy.
90034132022-09-15. Service bulletin. VEHICLE SPEED CONTROL:ACCELERATOR PEDAL. Accelerator Pedal Before replacing accelerator pedal, be sure to follow fault code diagnostic procedures in service manual. Make sure to check wiring and connectors. P2122 and P2127 will set if accelerator pedal connector is disconnected during diagnosis. Make sure codes are active before replacing pedal. DTC P2299 is usually caused by a two footed driver and accelerator pedal should not be replaced for this fault.
53034160A2019-05-20. Service bulletin. VEHICLE SPEED CONTROL; VEHICLE SPEED CONTROL:ACCELERATOR PEDAL. Part Description: Accelerator Pedal Issue Description: Vehicle has accelerator pedal fault code. Before replacing accelerator pedal, be sure to follow fault code diagnostic procedures in service manual. Make sure to check wiring and connectors. DTC P2299 is usually caused by a two footed driver and accelerator pedal should not be replaced for this fault.
18-020-162018-06-18. Service bulletin. ENGINE AND ENGINE COOLING; ELECTRICAL SYSTEM; POWER TRAIN. Flash: 6.4L Powertrain Diagnostic And System Improvements This bulletin involves reprogramming of the Powertrain Control Module (PCM) with the latest software. Customers may experience one or more of the following symptoms and/or a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find one or more of the following Diagnostic Trouble Codes (DTCs): · P0456 - EVAP System Small Leak. · P2299 - Brake Pedal Position/Accelerator Pedal Position Incompatible. Customers may also notice the following condition(s): · Brief engine idle fluctuation while in hot ambient temperatures. · A slight hesitation during light pedal application after engine cold start. · Driveline noises. · Engine stumble/hesitation on a very hard pedal acceleration from a dead stop. · Transmission enhancements during low speed braking turning maneuvers. · False detonation (spark knock) detected during a wide open throttle (LA) Challenger (Sales Codes ESH with DEC only). In addition, the following software enhancement is available: · Calibration Improvements for non-adaptive cruise control equipped vehicles.
90034132018-06-04. Service bulletin. VEHICLE SPEED CONTROL:ACCELERATOR PEDAL. Accelerator Pedal Before replacing accelerator pedal, be sure to follow fault code diagnostic procedures in service manual. Make sure to check wiring and connectors. P2122 and P2127 will set if accelerator pedal connector is disconnected during diagnosis. Make sure codes are active before replacing pedal. DTC P2299 is usually caused by a two footed driver and accelerator pedal should not be replaced for this fault.

The summaries are NHTSA's. Each bulletin's page links NHTSA's copy of the manufacturer's document.