WenmarOpen by Wenmar Pro

Service bulletins for the 2014 Chrysler 300

A bulletin is a manufacturer's communication to its dealers, as NHTSA indexes it. The summary is NHTSA's. The document is the manufacturer's: read it at NHTSA. A bulletin is not a recall, and listing a model year does not mean every vehicle of it is concerned.

323 on file from NHTSA, as of 2026-10-19.

By type

By component

By trouble code

Only bulletins with component: Engine are shown. Show all

Bulletins, newest first
S1709000010 Rev.2022-07-18. Service bulletin. ENGINE AND ENGINE COOLING:ENGINE:CRANK/CAMSHAFT POSITION SENSOR. Customer complaints may include abnormal engine noise, rough idle, lack of power, misfire. Upon investigation, it may be found that there is excessive camshaft lobe wear/lifter wear (roller failure) on one or more cam lobes and that camshaft/lifter replacement is necessary.
S1709000010 RevB2022-05-31. Service bulletin. ENGINE AND ENGINE COOLING; ENGINE. Customer complaints may include abnormal engine noise, rough idle, lack of power, misfire. Upon investigation, it may be found that there is excessive camshaft lobe wear/lifter wear (roller failure) on one or more cam lobes and that camshaft/lifter replacement is necessary.
D-16-032022-04-04. Service bulletin. ENGINE. Can/Am Warranty coverage
68143886A$2022-04-04. Service bulletin. ENGINE AND ENGINE COOLING:COOLING SYSTEM:RADIATOR ASSEMBLY. RADIATOR, Engine Cooling
S1809000007 Rev.2021-06-28. Service bulletin. ENGINE AND ENGINE COOLING. Customer Complaint May Include Engine Oil Leak Or Consumption
S1809000007 Rev.2021-04-26. Service bulletin. ENGINE AND ENGINE COOLING. Customer complaint may include engine oil leak/consumption.
90033572021-04-26. Service bulletin. ENGINE AND ENGINE COOLING. ADAPTER, Engine Oil Filter (Pentastar V6) All vehicles equipped with a 3.2L or 3.6L except for model year 2014 vehicles with leak concern: 1) Ensure the Oil Filter Adapter (OFA) Cap O-ring is seated in the proper groove in the cap and not damaged or cut. 2) If replacing the (OFA) due to a leak detected between (OFA) and block. Ensure the torque on the 5 bolts are torqued to 12nm. If not record the actual values, torque to 12nm and contact the FCA employees listed below. 3) Remove the (OFA) and replace the O-ring and gaskets only (Kit #68191356A$), NOT THE OFA. 4) If oil was drained, add oil dye to ensure the leak is repaired. For model year 2014 vehicles replace the Oil Filter Adaptor. 5) When replacing PN's 68310865A$ & 68308741A$, it may be necessary to transfer the Oil Temp/Pressure Sensor from the old OFA to the new OFA.
S1709000010 Rev.2021-02-16. Service bulletin. ENGINE AND ENGINE COOLING. Customer complaints may include abnormal engine noise, rough idle, lack of power, misfire. Upon investigation, it may be found that there is excessive camshaft lobe wear/lifter wear (roller failure) on one or more cam lobes and that camshaft/lifter replacement is necessary.
18-073-202020-09-28. Service bulletin. ENGINE; POWER TRAIN:AUTOMATIC TRANSMISSION:CONTROL MODULE:SOFTWARE; ELECTRICAL SYSTEM. Flash: Powertrain Control Module (PCM) Updates This bulletin involves reprogramming the Powertrain Control Module (PCM) with the latest software. Customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find one or more of the following Diagnostic Trouble Codes (DTCs):U1424-00 - Implausible Engine Torque Signal Received(2015 MY). P0456 - EVAP System Small Leak. P2610 - PCM Internal Engine Off Timer Performance. P2299 - Brake Pedal Position / Accelerator Pedal Position Incompatible. P0335 - Crankshaft Position Sensor Circuit(2014-2015 MY). U0140 - Lost Communication With Body Control Module(LC, LD and LX). P1621 - O2 Sensor Reference Voltage Circuit Low. P1622 - O2 Sensor Reference Voltage Circuit High. P0606 - Internal Control Processor. P0300 - Multiple Cylinder Misfire. P219A - Bank 1 Air-Fuel Ratio Imbalance. P219B - Bank 2 Air-Fuel Ratio Imbalance. P0307 - Cylinder 7 Misfire. P2096 - Downstream Fuel Trim System 1 Lean. P2097 - Downstream Fuel Trim System 1 Rich. The following software enhancements are also available(2015 MY):Reverse gear lock-out change from 16 kph (10 mph) to 4.8 kph (3 mph)(Sales Code EZC with DEC). Change to purge vapor control calibration(Sales Code EZH with DGJ). Improvements to vehicle overspeed control(Sales Code EZH with DGJ). Calibration update to the electronic voltage regulator voltage set point(Sales Code EZH with DGJ). Additional Symptoms:Customers with a Pursuit Dodge Charger (LD) may describe an unpleasant odor in the vehicle under certain extreme ambient conditions2013-2015 MY LD with (Sales Codes EZH with AHB or AHV only). Technicians may find that the original vehicle Frequency Operated Button Integrated Key (FOBIK) does not function properly following replacement of the Wireless Ignition Node (WIN/WCM). The Secret Key information stored in the PCM may be corrupt. This update will restore the PCM?s ability to store/transfer valid Secret Key information
S20080001132020-09-28. Service bulletin. ENGINE; ELECTRICAL SYSTEM. No Start Intermittently, Vehicle Requires Multiple Keyless Push To Start Attempts To Start Vehicle
UB4 Rev. 62020-05-26. Service bulletin. FUEL/PROPULSION SYSTEM; ENGINE. Emissions Recall UB4 Evaporative Emissions Canister
UB4 Rev. 52020-05-26. Service bulletin. ENGINE AND ENGINE COOLING. Revised Emissions Recall UB4 Evaporative Emissions Canister
UB4 Rev. 52020-05-18. Service bulletin. ENGINE AND ENGINE COOLING. Revised Emissions Recall UB4 Evaporative Emissions Canister
UB4 Rev. 52020-04-27. Service bulletin. FUEL/PROPULSION SYSTEM; ENGINE. Revised Emissions Recall UB4 Evaporative Emissions Canister
UB4 Rev. 42020-04-06. Service bulletin. ENGINE. Revised Emissions Recall UB4 Evaporative Emissions Canister
18-039-15 REV-A2018-12-17. Service bulletin. ENGINE; POWER TRAIN. Flash: 6.4L Powertrain Diagnostic And System Enhancements This bulletin involves reprogramming the Powertrain Control Module with the latest available software. A small number of customers may experience one or more of the following conditions: ? With the cluster set on metric units, they are unable to accurately increase or decrease the cruise control set speed using the resume or set buttons. Instead of changing vehicle speed by 1 KPH when pressing the buttons, the vehicle speed will increase approximately 1.6 KPH. ? Potential gear hunting during cruise operation at lower vehicle speeds (25-40 mph). In addition, a small number of customers with manual transmission equipped vehicles may experience certain symptoms/conditions or a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the Technician may find that the following Diagnostic Trouble Code has been set: ? P2096 - Downstream Fuel Trim System 1 Lean. (LC vehicles with Sales Code ESH with a manual transmission (Sales Code DEC). ? P2097 - Downstream Fuel Trim System 1 Rich. (LC vehicles with Sales Code ESH with a manual transmission (Sales Code DEC). ? P2098 - Downstream Fuel Trim System 2 Lean. (LC vehicles with Sales Code ESH with a manual transmission (Sales Code DEC). ? P2099 - Downstream Fuel Trim System 2 Rich. (LC vehicles with Sales Code ESH with a manual transmission (Sales Code DEC). ? P0300 - Multiple Cylinder Misfire (set during engine warm-up) (LC vehicles with Sales Code ESH with a manual transmission [Sales Code DEC]).
18-052-152018-12-03. Service bulletin. ENGINE AND ENGINE COOLING. Flash: 5.7L Powertrain Diagnostic And System Enhancements This bulletin involves reprogramming the Powertrain Control Module (PCM) with the latest available software. A small number of customers may experience one or more of the following symptoms or a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find one or more Dagnostic Trouble Codes (DTCs). ? DTC: U0140 - Lost Communication With Body Control Module (TIPM) stored in the Engine Control Module (ECM) memory (applies only to LC vehicles). ? DTC: P1621 - O2 Sensor Reference Voltage Circuit Low ? DTC: P1622 - O2 Sensor Reference Voltage Circuit High ? DTC: P0606 - Internal Control Processor ? DTC: P219A - Air-Fuel Ratio Cylinder Imbalance Bank 1 ? P0300 - Multiple Cylinder Misfire (applies only to vehicles using a block heater in ambient temperatures greater than -20°F (-29°C)) ? Technicians may find that the original vehicle Frequency Operated Button Integrated Key (FOBIK) does not function properly following replacement of the Wireless Ignition Node (WIN/WCM). The Secret Key information stored in the PCM may be corrupt. This update will restore the PCM?s ability to store/transfer valid Secret Key information (applies only to LC vehicles). ? Accuracy improvements for the Automatic Oil Change Indicator (AOCI) system.
09-008-152018-11-26. Service bulletin. ENGINE. 3.6L Oil Loss Diagnostic Aid This bulletin involves additional information on oil loss.
21-004-152018-11-19. Service bulletin. POWER TRAIN; ENGINE; ELECTRICAL SYSTEM. Flash: 845RE Transmission Shift Enhancements This bulletin involves reprogramming the Transmission Control Module (TCM) with the latest available software. The following TCM calibration improvements are available for vehicles equipped an 845RE Automatic Transmission (Sales Code DFL). These updates are listed by vehicle and engine. LD and LX vehicles equipped with a 3.6L engine (Sales Code ERB) ? Software to correct a harsh bump feel during a 2-1 downshift. ? Software to enable the scan tool based transmission ?Quick Learn.? ? Software to address customer concerns of Malfunction Indicator Lamp (MIL) illumination and Diagnostic Trouble Code (DTC) P215C Output Shaft Speed, Wheel Speed Correlation setting on AWD equipped vehicles. LX and WK vehicles equipped with a 3.0L engine (Sales Code EHD) ? Software to correct a harsh bump feel during a 2-1 downshift. WK vehicles equipped with a 3.6L engine (Sales Code ERB) ? ECO mode will not retain settings. If ECO mode is turned off, it will turn back on after the ignition is cycled. ? Software to correct a harsh bump feel during a 2-1 downshift. DS vehicles equipped with 3.6L engine (Sales Code ERB) ? Software to correct a harsh bump feel during a 2-1 downshift. ? Software to address a customer?s concern of less than desired shift quality in Four Wheel Drive (4wd) Low mode during medium to heavy acceleration. ? Software to address customer concerns of Malfunction Indicator Lamp (MIL) illumination and Diagnostic Trouble Code (DTC) P215C Output Shaft Speed, Wheel Speed Correlation setting on AWD equipped vehicles. ? Software improvements to powertrain braking in Tow/Haul mode. ? Software to improve downshift response from a medium to heavy pedal acceleration. ? Driveability improvements at higher altitudes. ? Software to improve acceleration during cruise control operation ? Software to correct a condition where DTC U11C3 - ESM Lost Communication With TCM On D-Pt CAN may have been displayed inste
07-002-152018-11-19. Service bulletin. ENGINE. Idler Pulley Noise During Cold Start This bulletin involves replacing the idler pulley. The customer may describe a loud high frequency noise that happens within 20 seconds of engine startup and lasts about 90 seconds intermittently during a cold engine start, approximately 0 degrees C (32 degrees F) and below.
07-002-15 REV. A2018-09-24. Service bulletin. ENGINE. Idler Pulley Noise During Cold Start This bulletin involves replacing the idler pulley. The customer may describe a loud high frequency noise that happens within 20 seconds of engine startup and lasts about 90 seconds intermittently during a cold engine start, approximately 0 degrees C (32 degrees F) and below.
18-034-14 REV. A2018-06-18. Service bulletin. ENGINE. P0520- Engine Oil Pressure Sensor Circuit This bulletin involves replacing the oil pressure sensor with a revised part. A small number of customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the Technician may find that the following Diagnostic Trouble Code (DTC) has been set: P0520 - Engine Oil Pressure Sensor Circuit
90036942018-06-11. Service bulletin. ENGINE AND ENGINE COOLING. Oil Pump Assembly If error code P06DD present on any Pentastar V6 application, please inspect oil pump for relief valve failure. See photo attached. If valve is found out of place please call Bob Jackson (248) 944-0466 bob.jackson@fcagroup.com, or Joe Lovell (734) 309-6467 joe.lovell@fcagroup.com before proceeding. If unable to reach after 15 minutes record the following information and proceed with oil pump replacement and hold part for return to FCA via Fastrack system
68105583A2018-06-11. Service bulletin. ENGINE AND ENGINE COOLING. Pentastar Oil Filter Adapter: Before replacing this part, please call any one of the following people. Engineering is seeking information regarding this part.~ Dye must be used to determine where the leak is coming from before replacing. Also please check the recently updated Service Bulletin Number 09-008-15. ~ First: Nick Morand Cell (248) 410-8078 - Nick.morand@fcagroup.com Second: Bob Jackson Cell (248) 944-0466 - bob.jackson@fcagroup.com Third: Joe Lovell Cell (734 309-6467 - joe.lovell@fcagroup.com If a response is not received within 15 mins, then proceed with the necessary repair.~
18-054-142018-06-11. Service bulletin. ENGINE AND ENGINE COOLING. Intermittent Extended Crank, Long Crank Time. This bulletin involves inspecting the Bank 1 Camshaft Position Sensor serial number and if necessary, replacing the sensor. A small number of customers may experience an intermittent 1 to 5 second extended crank condition when starting their vehicle. No DTCs will be present when this occurs.

The summaries are NHTSA's. Each bulletin's page links NHTSA's copy of the manufacturer's document.